心电地图仪中工频干扰的一种滤除方法

在心电地图仪中记录到的体表心电信号往往由于电磁的影响而引进工频干扰．基于体表心电信号中工频干扰的特点，作者提出了一种滤除工频干扰的方法，即就单独—胸导联信号通过提高频谱的分辨率来估计工频干扰的频率；基于最小均方误差准则来估计各导联信号中工频干扰的幅度和相位。文中还给出了该算法的流程图和滤波性能分析。模拟结果表明了该算法的有效性。应用该算法对心电地图仪中的工频干扰进行对消，取得了满意的结果。     

用于提高国产氩离子激光器相干长度的相干扩展器

本文报导了最近研制成功的用于提高国产氩离子激光器相干长度的相干扩展器。利用这种基于F-P理论的相干扩展器可以使国产氩离子激光器的相干长度由不足5cm一下提高到m的量级,功率损耗在25%～40%之间,有着很好的应用前景。     

MEMS移相器及其在微型通信系统中的应用

从传统移相器的构造和原理出发，进一步分析了MEMS移相器的结构、特性。结果表明，MEMS移相器具有传统移相器所无法比拟的体积小、损耗小、成本低、频带宽、易于集成等突出优点。随着高阻硅衬底在微波领域应用的扩展，MEMS移相器介质损耗大幅度降低，将能与信号处理电路一同集成于硅衬底上，便于相控阵雷达等通信系统实现微小型化。     

Improvement of RCA transistor using RTA annealing after theformation of interfacial oxide

A polysilicon emitter RCA transistor (an ultra-thin interfacial oxide layer exists between polysilicon and silicon emitter) is presented which can operate at 77 K for the first time. An ultra-thin (1.5 nm) interfacial oxide layer is grown deliberately between polysilicon and silicon emitter using RCA oxidation and excellent device stability is obtained after rapid thermal annealing (RTA) treatment in nitrogen atmosphere. The RCA transistor exhibits good electrical performance at very low temperature for an emitter area of 3 × 8 μm². The maximum toggle frequency of a 1:2 static divider is 1.2 GHz and 732 MHz at 300 K and 77 K, respectively     

减压渣油与FCC油浆共炭化的化学组成变化

考察了齐鲁石化胜利炼油厂催化油浆（FCC）和胜利减压渣油（VR）在490℃，0.8MPa下不同混合比的原料和不同反应时间的中间产物的HS、TS、PS、P及其1h中间产物的HS和TS的^1H-NMR。数据结果反映了体系的反应速度。掺入FCC油浆抑制了VR的反应活性，降低了体系的反应速度，增加了基质的溶解度；1h中间产物的组成结构更接近于原料及反应体系的反应性和基质的溶解度；1h中间产物的芳香度越高，取代基越少，侧链越短，基质对VR中的活性反应组分在炭化早期生成的高度缩合物质的溶解度越大。     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

Preparation and photochromism of nanocomposite thin film based on polyoxometalate and polyethyleneglycol

A photochromic nanocomposite based on Keggin structure phosphomolybdic acid (PMoA) well dispersed in polyethyleneglycol (PEG) was fabricated. TEM image showed that PMoA nanoparticles with narrow size distribution were finely dispersed in polymer matrix. FT-IR results showed that the Keggin geometry of polyoxometalates was still preserved inside the composites and strong coulombic interaction was built between PMoA and polymer matrix. Under UV irradiation, the film was reduced photochemically to yield a blue species, which was in accordance with a charge-transfer mechanism.