实验动物在血液制品中的应用

目的：阐述实验动物在血液制品生产质量控制过程中应用的重要性。方法：按《中华人民共和国药典》2005年版三部要求及相关项目的技术规范进行血液制品质量控制。结果：血浆数量150吨,可同时生产以下品种的产品,人血白蛋白共30批次,总瓶数约40万瓶（折10g）;免疫球蛋白类：共30批次,总瓶数约30万瓶（折2.5g）;人纤维蛋白原：共30批次,总瓶数约15万瓶（折0.5g）;人凝血酶原复合物：共30批次,总瓶数约12万瓶（折300IU）;人凝血因子Ⅷ：共30批次,总瓶数约10万瓶（折200IU）。需使用家兔870只、豚鼠300只小鼠750只。结论：实验动物应用于血液制品生产质量控制发挥了非常重要的作用。     

Synthesis and luminescence properties of Pr3+ doped CaxBa1?xTiO3 (0.3?x<1) fine particles

Ca _x Ba_1−x TiO₃ (CBT) fine particles doped with red luminescence center of Pr³⁺ ions (Pr: CBT) were successfully synthesized by salt assisted spray pyrolysis (SASP) process. Scanning electronic microscope (SEM) and laser scattering analysis demonstrate that salt can be removed from the surface of particles by washing with Milli-Q water and the particles can be further separated by ball-milling to get well-dispersed Pr³⁺ ions doped CBT fine particles. The luminescence properties, such as photoluminescence (PL) and mechanoluminescence (ML), of as-synthesized Pr: CBT particles were investigated. For Pr: CBT fine particles with different Ca molar ratios, all the samples show one emission at 612 nm, with increasing Ca molar ratio, PL intensity of Pr: CBT fine particles become stronger and stronger. When pressure was loaded on the Pr: CBT pellet, mechanoluminescence(ML) emission was measured. The results show that the ML intensity is proportional to the applied pressure.     

Cycling hardening and serration yielding of Fe-Ni-Cr alloy at high temperature under out-phase TMF

Behaviour of hardening and serration yield of a Fe-Ni-Cr alloy under isothermal cycling (ISC) and out-phase TMF was studied on the basis of varied hysteresis loops. Cycling hardening and serrated yielding for ISC depend on the temperature and the total strain range, stronger hardening with serrated yielding at higher strain range under ISC at 600 °C, but no hardening and serrated yielding occurred under ISC at 800 °C. Stronger hardening with stress serration occurred at the thermal path going to the lowest temperature, no stress serration occurred at the highest temperature under the out-phase. The hardening also depends on the total strain range, higher total strain range with lower cycling temperature resulted in a stronger hardening and remarkable serration yielding behavior. Weaker hardening without serrated yielding occurred at near 800 °C may due to an obvious cycling stress drop under out-phase TMF. Change in the shape of the hysteresis loops also expresses the degree of the damage of the tested alloy under out-phase and ISC.     

分时控制MOSFET固态高频感应加热电源研究

研究了一种采用分时控制方法的MOSFET固态高频感应加热电源,电源输出频率是功率器件工作频率的n倍(采用n个桥分时工作)。利用MATLAB/SIMULINK实现了分时控制的仿真,分析了分时控制的工作状态,对器件功耗进行了理论推导,并对如何实现分时控制进行了介绍,且根据仿真画出了并行控制和分时控制2种控制方式下MOSFET器件损耗的曲线图。仿真结果表明分时控制在实现固态感应加热电源的高频化方面优于并行控制。     

异辛酸钴的制备和应用

采用硫酸钴沉淀法制备异辛酸钴,并在水相与有机相的分离过程中添加助剂的方法,可使分离后有机相不经水洗即可彻底除去SO_4~(2-)离子,简化了工艺流程。介绍了异辛酸钴催干剂在4种醇酸磁漆中的应用及其性能检测结果。检测结果表明,异辛酸钴用于醇酸磁漆的性能指标达到或超过规定标准,尤其光泽、硬度两项指标优于同类产品水平,町作为环烷酸钴等常用催干剂的更新换代产品。     

太阳能溴化锂吸收式制冷系统吸收特性的研究

太阳能溴化锂吸收式制冷系统的吸收器采用传热、传质分离装置,利用预冷器预先冷却和喷淋吸收的方法完成对传热、传质的分离。通过建立吸收器的计算模型,分析冷冻水出口温度、冷却水进口温度、热水温度、喷淋温度、喷淋密度等因素对传热、传质的影响。利用传热、传质分离方法,使系统的吸收特性得到强化,从而使系统获得较高的性能系数。     

国内外聚碳酸酯市场及需求分析

聚碳酸酯(PC)综合性能好,其消费与生产增长举世瞩目,在世界五大通用工程塑料中占有重要地位。国内PC生产及消费量虽不大,但潜在市场不可忽视,发展与开拓工程塑料,特别是PC的应用与生产的开发,是我国化学和石化工业发展需要之一。     

A Sequential Design Approach for Switching ℌ∞ LPV Control

This paper proposes a sequential design scheme for switching ℌ_∞ LPV (Linear Parameter-Varying) control, aiming to reduce the computational complexity of the associated optimization problem. Different from the traditional approach that simultaneously designs switching LPV controllers and solves a high-dimensional optimization problem, the proposed sequential design approach renders a bundle of low-dimensional optimization problems to be solved iteratively. Individual ℌ_∞ LPV controller for each subregion is synthesized by independent PLMIs (Parametric Linear Matrix Inequalities) to guarantee ℌ_∞ performance, and controller variables are interpolated on the overlapped subregions such that the ℌ_∞ performance is also guaranteed on the overlapped subregion. Numerical examples are used to demonstrate the effectiveness of this method to reduce the computational load in each design iteration and improved ℌ_∞ performance over the conventional simultaneous design method with well-tuned interpolation coefficient.

     

On the mechanical performance of closed cell Al alloy foams

The mechanical properties of three different commercially available closed cell Al alloys all made by foam casting are examined. The objective is to assess the roles of cell morphology and of imperfections in governing the basic properties: stiffness, yield strength and fracture resistance. This assessment provides goals for manufacturing strategies that enable attainment of good mechanical performance with affordable process technologies. A prevalent role of curves and wiggles in the cell walls on stiffness and strength (anticipated by models) is affirmed by the present measurements. Systematically larger stiffnesses and yield strengths found in tension than in compression are consistent with a prominent role exerted by such imperfections. Moreover, foam casting is apparently capable of cell morphologies that impart properties approaching the best achievable values for an isotropic closed cell solid, devoid of imperfections. There are associated implications for performance and affordability. Fracture measurements indicate crack growth occurring along the cell walls by a mechanism analogous to the plastic tearing of thin sheets. The crack growth resistances are in the range of 1 kJm⁻². This mechanism infers a toughness that scales with the cell wall thickness and its yield strength.     

探索中国民营企业经营模式创新之路——岷山公司推行模拟法人经营体制

中国民营企业经营现状据第一部《中国民营企业发展报告》蓝皮书统计，中国300多万家私营企业90％以上是家族企业，既有单一业主制的企业，也有合伙制的企业、共有制的企业，甚至还出现了家族成员保持临界控制权的企业集团。