Effect of surface treatment on segregation of impurities in haematite

Surface segregation of various impurities such as Mg, Si, Ca, Al and Cr were determined for the haematite phase (Fe₂O₃) annealed in two different gas compositions involving (1) air at 1173 K, and (2) a gas mixture containing sulphur at 773 K. The objective of work was to establish the effect of the gas-phase composition on segregation of lattice defects. The near-surface segregation profiles of the impurities were determined by secondary ion mass spectrometry. The depth profile analysis was made by sputtering using an Ar⁺ primary beam of energy 30 keV. The surface charge was neutralized by an electron gun. It was found that annealing Fe₂O₃ under a gas phase containing sulphur resulted in the formation of an Fe(SO₄)₃ surface layer. It was observed that the two surface treatment procedures applied (both with and without sulphur) result in Mg enrichment in the near-surface region of Fe₂O₃. Si and Ca exhibit an enrichment and impoverishment after the surface treatments 1 and 2, respectively. Finally, the near-surface layer is impoverished in Cr and Al after both types of surface treatment. Experimental results are discussed in terms of segregation driving forces of the respective elements and the possible effect of sulphur on the gas-solid heterogeneous kinetics.     

Fabrication of Strain-Relaxed Si<Subscript>1 − <Emphasis Type="Italic">x</Emphasis></Subscript>Ge<Subscript>x</Subscript>/Si(001) Buffer Layers of Low Surface Roughness

The results are presented of the fabrication of strain-relaxed graded Si_{1 − x} Ge_x/Si(001) buffer layers with a maximum Ge fraction of about 0.25 that have a low density of threading dislocations (<10⁶ cm⁻²) and low surface roughness. The buffer layers are grown by atmospheric-pressure hydride CVD. It is found that chemical mechanical polishing can reduce their surface roughness to a level comparable with that of the original Si(001) substrates. It is shown that the polished buffer layers can serve as substrates for MBE-grown SiGe/Si heterostructures.__________Translated from Mikroelektronika, Vol. 34, No. 4, 2005, pp. 243–250.Original Russian Text Copyright © 2005 by Vostokov, Drozdov, Krasil’nik, Kuznetsov, Novikov, Perevoshchikov, Shaleev.     

Fish assemblages and stream hydraulics: consistent relations across spatial scales and regions

General relationships between organisms and their habitat, consistent across spatial scales and regions, suggest the existence of repeatable ecological processes and are useful for the management of stream networks. From published data, we defined four guilds of European fish species with contrasting preferences for microhabitat hydraulics within stream reaches. At the scale of stream reaches and across 139 French sites (590 460 fishes sampled), we analysed how fish guild proportions were related to reach hydraulics (proportion of pools vs. riffles %POOL; median discharge by unit width Q50/W). The strongest correlations were observed between two fish guilds and %POOL (p < 0.001, r² ≥ 0.41) and between one fish guild proportion and Q50/W (p < 0.001, r² = 0.10). These reach–scale relationships were consistent across six large French basins, and consistent with the analyses made at the microhabitat scale. Therefore, microhabitat preferences for hydraulics are strong enough to generate consistent reach‐scale community responses to hydraulics across regions, despite the influence of other filters such as temperature, nutrient levels or history. The distribution of basic geomorphic features (pools, riffles) in streams and their modification (by dams, weirs and dikes) can modify the proportion of fish guilds by up to 80%, probably contributing to the long‐term decline of riffle‐dwelling species in Europe. Copyright © 2006 John Wiley & Sons, Ltd.     

PECVD of diamond-like carbon (a-C:H) from the decomposition of methane in a high-density inductively coupled discharge

The paper describes an experimental investigation of the diamond-like carbon deposition process from methane precursor with an innovative high-density inductively coupled plasma source. It appears that a high plasma density allows a fast growth of diamond-like carbon coatings exhibiting a high hardness. In contrast to what is usually found in the literature, it seems that the ion species participate significantly to the growth of the carbon film when exposed to a high ion flux.     

CMOS gyrator-C active transformers

A systematic approach for synthesising gyrator-C active transformers using MOS transistors is presented. The topology of gyrator-C active inductors and their characteristics are briefly reviewed first. This is followed by the development of ideal gyrator-C active transformers, where only the capacitor loads of the transconductors synthesising active transformers are considered. The self and mutual inductances of both the primary and secondary windings of active transformers are investigated in detailed. Non-ideal gyrator-C active transformers are developed with the consideration of both the resistance and capacitance loads of transconductors. The intrinsic relation between the self and mutual inductances is derived. The configuration of gyrator-C active transformers with multiple primary and secondary windings is also developed. The proposed active transformers offer large and tunable self and mutual inductances with virtually no silicon area requirement. Several practical implementations of the proposed active transformers have been realised in TSMC-0.18 mum 1.8 V CMOS technology and analysed using SpectreRF with BSIM3v3 device models. Simulation results on voltage transfer characteristics, self and mutual inductances, quality factors, stability, the effect of process variations, and noise are presented. The application of the proposed active transformers is exemplified using a 1.6 GHz active transformer quadrature oscillator.     

Skew-cyclic codes

We generalize the notion of cyclic codes by using generator polynomials in (non commutative) skew polynomial rings. Since skew polynomial rings are left and right euclidean, the obtained codes share most properties of cyclic codes. Since there are much more skew-cyclic codes, this new class of codes allows to systematically search for codes with good properties. We give many examples of codes which improve the previously best known linear codes.     

Sandwich panels with Kagome lattice cores reinforced by carbon fibers

Stretching dominated Kagome lattices reinforced by carbon fibers were designed and manufactured. The sandwich panels were assembled with bonded laminate skins. The mechanical behaviors of the sandwich panels were tested by out-of-plane compression, in-plane compression and three-point bending. Different failure modes of the sandwich structures were revealed. The experimental results showed that the carbon fiber reinforced lattice grids are much stiffer and stronger than foams and honeycombs. It was found that buckling and debonding dominate the mechanical behavior of the sandwich structures, and that more complaint skin sheets might further improve the overall mechanical performance of the sandwich panels.     

Improving Cost Estimates of Construction Projects Using Phased Cost Factors

Central to cost-based competition is the capability to accurately predict the cost of delivering a project. Most literature on cost estimation focuses on specific estimation methods as generic techniques and little attention has been paid to the unique requirements at each project stage. This note attempts to identify the critical factors for effective estimation at various stages of typical construction projects. Drawing from organization control theory and cost estimating literature, this note develops a theoretical framework that identifies the critical factors for effective cost estimation during each project phase of a conventional construction project. The underlying logic is that as a cost estimating effort progresses, both task programmability and output measurability improve. As a result, control effort will shift from input-oriented control to a combination of output and behavior control.     

On the cover.

Discusses the cover art for this issue of American Psychologist. Portions of the article are based on an interview with the artist, Melissa Miller, on November 6, 2006. (PsycINFO Database Record (c) 2010 APA, all rights reserved)