Understanding the corrosion of molten ZnCl2 on metal surfaces is significant for the corrosion protection of metals, sustainable use of molten salts, preparation of ZnO coatings, and so on. In this paper, surfaces of pure Ni, Cr, and Fe corroded by molten ZnCl2 were investigated. The results show that Ni suffered very slight corrosion, while Cr experienced more serious corrosion than Ni, but lighter corrosion than Fe. The morphology of the corrosion of Cr and Fe, respectively, presented pitting and intergranular corrosion characteristics. Furthermore, nanostructured ZnO coatings were obtained on the surfaces of Ni and Fe, but not on the surface of Cr. The ZnO coating on the Ni surface was doped with a small amount of Zn5(OH)8Cl2, and the ZnO coating on the Fe surface was doped with ZnFe2O4 and Zn2OCl2. The coatings on the Ni and Fe surfaces had an average thickness of 1.5 and 50 μm, respectively. 相似文献
The {100} facet of single-crystalline TiO2(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO2(B) nanobelts from H2Ti3O7 with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO2 formula with specific capacity up to 335 mAh g−1, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g−1 after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures. 相似文献
Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm2 for Mg alloy to 13 μA/cm2 for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications. 相似文献
Although Mg alloy possesses high specific strength, low density, and good biocompatibility, poor corrosion resistance hinders its further applications. In the present study, an innovative protective layer against corrosion was prepared on the AZ31 Mg alloy via alkali pretreatment followed by vanillic acid treatment. The alkali pretreatment supplied –OH for the AZ31 Mg alloy surface to react with vanillic acid. The vanillic acid treatment played a crucial role in enhancing the corrosion resistance due to the excellent ability to act as a barrier and retard aqueous solution penetration, which effectively isolated the underlying Mg alloy from the corrosive environment. The corrosion current density of alkali and vanillic acid-treated Mg alloy (AZ31V) almost showed two orders of magnitude lower values in comparison with that of the AZ31 Mg alloy, and the corrosion potential of AZ31V Mg alloy increased from −1.41 to −1.25 V. The immersion tests proved that there was no occurrence of severe corrosion. Hence, the alkali pretreatment and vanillic acid treatment may represent a promising method to improve the corrosion resistance of Mg alloy. 相似文献
Breast cancer is one of the most common female malignancies, as well as the second leading cause of mortality for women. Early detection and treatment can dramatically decrease the mortality rate. Recently, automated breast volume scanner (ABVS) has become one of the most frequently used diagnose methods for breast tumor screening because of its operator-independent and reproducible advantages. However, it is a challenging job to obtain the tumors’ accurate locations and shapes by reviewing hundreds of ABVS slices. In this paper, a novel computer-aided detection (CADe) system is developed to reduce clinicians’ reading time and improve the efficiency. The CADe system mainly contains three parts: tumor candidate acquisition, false-positive reduction and tumor segmentation. Firstly, a local phase-based approach is built to obtain breast tumor candidates for further recognition. Subsequently, a convolutional neural network (CNN) is applied to reduce false positives (FPs). The introduction of CNN can help to avoid complicated feature extraction as well as elevate the accuracy and efficiency. Finally, superpixel-based segmentation is used to outline the breast tumor. Here, superpixel-based local binary pattern (SLBP) is proposed to assist the segmentation, which improves the performance. The methods were evaluated on a clinical ABVS dataset whose abnormal cases were manually labeled by an experienced radiologist. The experiment results were mainly composed of two parts. At the FP reduction stage, the proposed CNN achieved 100% and 78.12% sensitivity with FPs/case of 2.16 and 0. At the segmentation stage, our SLBP obtained 82.34% true positive, 15.79% false positive and 83.59% Dice similarity. In summary, the proposed CADe system demonstrated promising potential to detect and outline breast tumors in ABVS images.
AbstractGraphene oxide (GO) was functionalized by polyether amine (PEA) via two methods which were one-pot modification in acetone (GON) and two steps with the intermediate product of GOCO-Cl generated (GONS). There were more PEA successfully grafted onto GO for GONS than GON. The onset polymerization temperatures of the benzoxazine (Bz) composites decreased by the inclusion of 1?wt% of GO, GON or GONS. Thermal stability of the polybenzoxazine (PBz) composites was significantly improved indicated from the increase of weight loss temperature. T10, T20 and T50 values of the composites with GONS were higher than that of the others. Toughness of PBzs may be enhanced by the incorporation of nanofillers, and GONS had stronger interfacial interaction with PBz matrix than GON. 相似文献