负载型固体催化剂在生物柴油制备中的研究现状及应用前景

对生物柴油及其制备方法进行简单介绍，重点综述了负载型固体酸、碱催化剂在生物柴油制备中的研究现状，并指出当前负载型固体催化剂研制中的研究热点，最后对其应用前景了进行展望。     

Global Asymptotical Synchronization of Chaotic Lur'e Systems Using Sampled Data: A Linear Matrix Inequality Approach

Sampled-data feedback control for master-slave synchronization schemes that consist of identical chaotic Lur'e systems is studied. Sufficient conditions for global asymptotic synchronization of such chaotic Lur'e systems are obtained using the free-weighting matrix approach and expressed in terms of linear matrix inequalities (LMIs). With the help of the LMI solvers, the sampled-data feedback control law can easily be obtained to globally asymptotically synchronize Lur'e chaotic systems. The effectiveness of the proposed method is finally illustrated via numerical simulations of chaotic Chua's circuits.     

基于MoCA标准的家庭网络研究

本文描述了一种基于MOCA标准的家庭网络,并对该网络及设备进行了基本性能的测试.本文首先介绍了家庭网络的发展现状,对目前的各种家庭网络标准进行了比较.在此基础上详细描述了基于MOCA标准的家庭网络,并对该网络的设计,实现、网络性能进行了详述.然后对该网络进行了测试并得出了相关的测试结论.最后指出该网络的不足及改进之处.     

Tri-Gate Bulk MOSFET Design for CMOS Scaling to the End of the Roadmap

A tri-gate bulk MOSFET design utilizing a low-aspect-ratio channel is proposed to provide an evolutionary pathway for CMOS scaling to the end of the roadmap. 3-D device simulations indicate that this design offers the advantages of a multi-gate FET (reduced variability in performance and improved scalability) together with the advantages of a conventional planar MOSFET (low substrate cost and capability for dynamic threshold-voltage control).     

爆轰试验用新型射频连接器的结构设计

针对目前爆轰试验中使用的机械密封射频连接器存在的问题.设计了基于玻璃封接技术的新型密封射频连接器结构,并进行了射频反射补偿计算和强度分析.本项研究为爆轰条件下新型密封射频连接器的研制提供了设计依据.     

Automating application software generation

Many approaches have been proposed to enhance software productivity and reliability. These approaches typically fall into three categories: the engineering approach, the formal approach and the knowledge-based approach. But the optimal gain in software productivity cannot be obtained if one relies on only one of these approaches. This paper describes the work in knowledge-based software engineering conducted by the authors for the past 10 years. The final goal of the research is to develop a paradigm for software engineering which integrates the three approaches mentioned above. A knowledge-based tool which can support the whole process of software development is provided in this paper.     

Sol-Gel Preparation of LaNiO3 and Its Physical and Chemical Properties

LaNiO3 was synthesized by sol-gel method in which lanthanum nitrate and nickel nitrate were used as start materials and citric acid was used as complex for gel formation.The precursor was dried and subsequently heated at elevated temperature to form the desired product.XRD analysis shows that pure LaNiO3 was synthesized.Electrical conductivity and electrochemical performance of the material were tested.The electrical conductivity decreases from 34.5that there are current peaks in the curve, which is the evidence of the electrochemical activity of LaNiO3.     

Residual stresses and transformation toughening in MoSi2 composites reinforced with partially stabilized zirconia

The results of study of the effects of yttria stabilization (0–6 mol.%) on the room-temperature fracture behavior and toughening mechanisms in zirconia-reinforced MoSi₂ are presented in this paper. Transformation toughening is shown to occur only in composites reinforced with zirconia particles stabilized with 2 mol.% yttria. However, the fracture toughness levels are comparable in the other composites with yttria levels between 0 and 6 mol.%. Toughening in the other composites is attributed to the combined effects of residual stress, microcrack shielding/anti-shielding and/or crack deflection. A rigorous micromechanics-based model is presented for the estimation of residual stress levels in brittle materials reinforced with phases that can transform during cooling or under stress. The model is applied successfully to the rationalization of the observed fracture and toughening phenomena.     

60m高度处单片露天超高混凝土悬臂墙的设计与施工

通过采用竖向预应力技术 ,解决了 60m高度处单片 8m高悬臂钢筋混凝土墙根部裂缝宽度超过规范限值的问题 ;采用将预应力钢绞线顶端锚固于墙高中段等结构和施工措施 ,控制墙体长细比不超过 3 0 ,减少了由于长细比过大对墙体承载力的不利影响