Failure mode transition and energy dissipation in naturally occurring composites

The microstructural aspects of compressive inelastic deformation in balsa wood are investigated with emphasis on the failure mode transition and its effects on energy dissipation characteristics. The architectural features as well as the composite character of cell wall ultrastructure are discussed in a framework to understand the complex interrelationship between microstructure and macroscopic behavior in this extremely lightweight cellular biocomposite. Based on this discussion and experimental results, it is concluded that the biomimetic approach may prove to be a viable strategy in designing composite structures with high specific energy absorption capacity.     

Optimal Control of the Primary Drying Stage of Freeze Drying of Solutions in Vials Using Variational Calculus

The problem of operating freeze drying of pharmaceutical products in vials placed in trays of a freeze dryer to remove free water (in frozen state) at a minimum time was formulated as an optimal control problem. Two different types of freeze dryer designs were considered. In type I freeze dryer design, upper and lower plate temperatures were controlled together, while in type II freeze dryer design, upper and lower plate temperatures were controlled independently. The heat input to the material being dried and the drying chamber pressure were considered as control variables. Constraints were placed on the system state variables by the melting and scorch temperatures during primary drying stage. Necessary conditions of optimality for the primary drying stage of freeze drying process in vials are derived and presented. Furthermore, an approach for constructing the optimal control policies that would minimize the drying time for the primary drying stage was given. In order to analyze optimal control policy for the primary drying stage of the freeze-drying process in vials, a rigorous multi-dimensional unsteady state mathematical model was used. The theoretical approach presented in this work was applied in the freeze drying of skim milk. Significant reductions in the drying times of primary drying stage of freeze drying process in vials were obtained, as compared to the drying times obtained from conventional operational policies.     

Start-up and steady-state results of a full-scale UASB reactor treating malting wastewater.

An Imhoff tank was reconstructed into a 250 m3 UASB reactor in order to treat a malting plant wastewater. The UASB was inoculated with sludge from an anaerobic lagoon used for slaughterhouse wastewater treatment. After two months of operation the reactor achieved full load with an HRT of 17 h, a COD removal higher than 80% and a biogas production of 300 m3/day (77% average methane content), with an organic loading rate of 3.6 kgCOD/m3.d (0.24 kgCOD/kgVSS.d). A yield coefficient of 0.09 gVSS/gCODrem was found from a mass balance. The fat present in the inoculated sludge (48 mg/gSSV) did not affect the start up performance. Sludge from the inoculum with high content of fat (270 mg/gSSV), was separated by flotation in the first week of operation. The COD removal efficiency was scarcely influenced by the reactor operation temperature (17-25 degrees C).     

Optimised anaerobic treatment of house-sorted biodegradable waste and slaughterhouse waste in a high loaded half technical scale digester.

Anaerobic co-digestion of organic wastes from households, slaughterhouses and meat processing industries was optimised in a half technical scale plant. The plant was operated for 130 days using two different substrates under organic loading rates of 10 and 12 kgCOD.m(-3).d(-1). Since the substrates were rich in fat and protein components (TKN: 12 g.kg(-1) the treatment was challenging. The process was monitored on-line and in the laboratory. It was demonstrated that an intensive and stable co-digestion of partly hydrolysed organic waste and protein rich slaughterhouse waste can be achieved in the balance of inconsistent pH and buffering NH4-N. In the first experimental period the reduction of the substrate COD was almost complete in an overall stable process (COD reduction >82%). In the second period methane productivity increased, but certain intermediate products accumulated constantly. Process design options for a second digestion phase for advanced degradation were investigated. Potential causes for slow and reduced propionic and valeric acid degradation were assessed. Recommendations for full-scale process implementation can be made from the experimental results reported. The highly loaded and stable codigestion of these substrates may be a good technical and economic treatment alternative.     

Analysis of feedback for higher order polarization-mode dispersion mitigation of NRZ 40-Gb/s optical transmission

First-order polarization-mode dispersion (PMD) compensation by means of a polarization controller and a differential delay line is not sufficient to guarantee error-free transmission for 40-Gb/s channels when higher order effects severely increase signal distortion. Higher order mitigation is possible by cascading more than one first-order block. However, only two-stage or three-stage devices remain simple enough to be actually controlled. The performance of such higher order PMD compensators is evaluated by means of numerical simulations. Two different feedback signals have been used, demonstrating that first-order and higher order PMD distortion of nonreturn-to-zero (NRZ) pulses at 40 Gb/s can be strongly mitigated for instantaneous values of the differential group delay (DGD) up to the bit slot, when the compensator is properly controlled.     

Trajectory control of incompletely restrained parallel-wire-suspended mechanism based on inverse dynamics

This paper discusses parallel wire mechanisms where an end-effector of the mechanism is suspended by multiple wires. The mechanisms enable not only three-dimensional (3-D) positioning but also 3-D orienting of the end-effector, unlike typical wire suspension-type mechanisms such as overhead crane. To discuss the parallel-wire-suspended mechanisms generally, two forms of basic dynamic equations are presented. Then the parallel wire mechanisms are classified into two types based on the basic equations. Dynamical properties of the two types of wire-suspended positioning mechanism are discussed. In this paper, one of the wire-suspended mechanism, incompletely restrained-type parallel wire mechanism, is mainly discussed on its inverse dynamics problem and its trajectory control problem. The inverse dynamics problem for the incompletely restrained-type mechanism plays an important role on its control problem, because the mechanism has low stiffness based on incomplete constraints on the suspended object which is governed by its dynamics. The paper proposes an antisway control method for the suspended object. In the method, the inverse dynamics calculation is used for nonlinear dynamics compensation to control the suspended object of the incompletely restrained parallel wire mechanism.     

Segmented polymer networks containing amino‐dendrimers

Polymer networks in which poly(propylene imine) dendrimers (Astramol?) are connected to each other by linear polytetrahydrofuran (polyTHF) segments, were prepared by two methods. The first method was a one‐step procedure in which bifunctionally living polyTHF, obtained by initiation of the THF polymerization with trifluoromethane sulfonic anhydride (triflic anhydride), was reacted with an amino‐dendrimer. This reaction was very fast but did not allow formation of the end products. The second method was a two‐step procedure. In a first step, living polyTHF, prepared with acryloyloxybutyl triflate as initiator, was grafted on an amino‐dendrimer, to form a star‐like, acrylate‐terminated polyTHF multi‐macromonomer with the dendrimer as core. In a second step, networks were obtained by Michael addition between the acrylate end‐groups and unreacted amino‐groups of the dendrimer. This cross‐linking reaction occurred spontaneously upon heating of the solution of the multi‐macromonomer with gelation times varying from a few minutes to a few hours, depending on the temperature and the composition of the prepolymers. With this method it was possible to prepare networks in the form of coatings or films. © 2003 Society of Chemical Industry     

Teaching robust programming

Robust programming aims to prevent abnormal termination or unexpected actions and requires code to handle bad (invalid or absurd) inputs in a way that is consistent with the developer's intent. For example, if an internal error occurs, the program might terminate gracefully rather than simply failing, providing enough information for the programmer to debug the program and avoiding giving the user additional access or information. This article focuses on teaching these principles.     

Low Temperature Physics at the Laboratoire National des Champs Magnétiques Pulsés in Toulouse

An overview over past and present activities and future developments at the Toulouse pulsed magnetic field facility is given, both as far as technical developments of the infrastructure, as well as low temperature physics performed at the LNCMP are concerned.