Theory of residence-time control by output feedback

The problem of residence-time control by the observer-based output feedback is formulated and solved for the case of linear systems with small additive input noise. Both noiseless and noisy measurements are considered. In the noiseless measurements case, it is shown that the fundamental bounds on the achievable residence time depend on the nonminimum phase zeros of the system. In the noisy measurements case, the achievable residence time is shown to be always bounded, and an estimate of this bound is given. Controller design techniques are presented. The development is based on the asymptotic large deviations theory. Recommended by T K. Caughey     

Electrical characterization of megabit DRAMs. 11. Internal testing

For pt.I. see ibid., vol.8, no.3, p.36-43 (1991). Contactless tools for testing inside dynamic RAMs, including hot-spot detection, emission microscopy, scanning laser microscopy, and submicron electron beam testing, are described. Basic principles and experimental setups are described. The utility of the techniques is assessed     

Thermal analysis of the architecture of old and new houses at Ghadames

The study suggests improvements in the design of new houses to conserve energy and enhance indoor thermal comfort. Summer temperature records show that a new house has an average indoor temperature of 35°C with the ambient average 31°C. The traditional house in the old city recorded 28°C for the same period. Winter temperatures in both types of houses were similar (12°C) when not occupied. Architectural features of the two houses were compared to identify those responsible for difference in the thermal performance. Larger exposed surface and window areas, higher overall heat transfer coefficient and weaker thermal coupling with the ground for the new houses seems to contribute to their inferior thermal performance.     

The glass fibre-polymer interface: II—Work of fracture and shear stresses

Pull-out experiments have been carried out on single production fibres under carefully controlled conditions. Four parameters were determined. The interfacial yield stresses, of about 9–14 MPa, were very much smaller than the shear strengths of the bulk polymers in the case of an epoxy, whether post-cured or not, and a non-post-cured polyester. Values for the work of fracture of the interface varied from 140 to 300 Jm^?2, and again were less than those of the polymer. Interface failure sometimes took place in the epoxy rather than at the fibre surface, whereas with the polyester it always took place at the fibre surface. After interface failure, pull-out was governed by friction, with maximum shear stresses of 7–10 MPa for polyester, and 21–34 MPa for epoxy, the higher values being obtained for the post-cured resins. Average frictional shear stresses were sometimes less than a half of the maximum shear stress, indicating that the fibre Poisson's shrinkage was playing an important role in the pull-out process. A silicone release agent reduced the frictional shear stresses to 2·5 MPa, with both resins.     

FMR and EXAFS modeling of heat-treated Fe-rich and Co-rich TM-M thin films

Ion-beam sputter-deposited alloy films of Co/sub 74/Fe/sub 6/B/sub 15/Si/sub 5/ and Fe/sub 75/Ni/sub 5/B/sub 15/Si/sub 5/ were examined for their magnetic and structural properties. Films were characterized by ferromagnetic resonance, vibrating sample magnetometry, and extended X-ray absorption fine structure (EXAFS) analysis. Using atomic parameters deduced from EXAFS modeling and fitting procedures, magnetic properties were calculated with no adjustable parameters. Correlation between perpendicular FMR measurements and EXAFS first-shell modeling suggests a low-temperature formation of cobalt-borides in the Co/sub 74/Fe/sub 6/B/sub 15/Si/sub 5/ alloy. Annealed Fe/sub 75/Ni/sub 5/B/sub 15/Si/sub 5/ samples did not display evidence of structural and/or magnetic instabilities until the onset of long-range crystallization near T/sub ann/=400 degrees C.<>     

Calculation of the molar volume of liquid hydrocarbons

Equations are proposed for calculating the molar volume of liquid hydrocarbons used in production of surfactants. With such data, it will be possible to calculate most of the physicochemical properties of these hydrocarbons to solve many process problems. __________ Translated from Khimiya i Tekhnologiya Topliv i Masel, No. 6, pp. 39–41, Novemmber–December, 2006.