Investigation into Polarization of Unloaded and Loaded Microstrip Square-Ring Antennas

The polarization characteristic of unloaded and loaded square-ring microstrip antennas is investigated. Several different loading types like single-stub, dual-stub, notch, gap and shorting-pin are considered and their effects are studied. Loading enables feeding using a 50-Omega probe. The simulation and measurement results show that the loading techniques excite a loaded TMy ₁₁ mode that is orthogonal to the unloaded TMx ₁₁ mode. This indicates that by loading the ring antenna its polarization can be switched adaptively. However, the purity of the loaded and unloaded modes depends on the loading type. For some loading types like gap and shorting-pin, the excitation of the unloaded mode seems negligible, in comparison to the loadings by stub and notch. For the stub and notch loaded antennas the unloaded mode is also present, and its excitation efficiency is frequency dependent. Thus, their polarization plane, which is due to both loaded TMy ₁₁ and unloaded TMx ₁₁ modes, also becomes frequency dependant. The results of this investigation can be useful in selecting the loading methods for high-impedance microstrip ring antennas, and control of their impedance and polarization. The knowledge of the antenna polarization is essential in communications, and its dependence on the loading type can be used as an important parameter in design of adaptive antennas and sensors.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Interval based MINLP superstructure synthesis of mass exchange networks

A new simultaneous synthesis approach for mass exchange networks (MENs) is presented. The technique is adapted from the interval based mixed integer non-linear program (MINLP) superstructure (IBMS) synthesis of heat exchanger networks (HENs). The superstructure interval boundary compositions are defined by the supply and target compositions of either the rich or lean set of streams. Each rich and lean stream in the superstructure has the potential of exchanging mass with streams of opposite kind in each interval based on mass transfer feasibility. The model harnesses the strengths of the stagewise superstructure and the pinch technology methods for mass exchange network synthesis (MENS). The IBMS approach simultaneously trades-off the capital and operating costs for MENs. The superstructure composition interval defining approach introduced in this paper enforces the mixing of split streams at equal compositions, hence there is no need to include mixing equations in the model. Fixing the interval boundaries helps to eliminate the complexities involved in initialisations, thus the region of search for the optimum solution is reduced. The IBMS model is applied to MENS problems involving continuous contact and staged columns. It is also extended to problems involving multiple mass separating agents (MSAs) and regeneration. The results obtained compare well with those in the literature.     

Sequential batch reactor for eucalypt kraft pulp effluent treatment with Trametes versicolor

BACKGROUND: A sequential batch reactor (SBR) was used for eucalypt kraft pulp effluent treatment with Trametes versicolor. A 2³ full factorial design and response surface methodology were applied to optimise the batch fermentation conditions. Effluent concentration, culture medium and inoculum age were the factors selected for this study in order to optimise the reduction of chemical oxygen demand (COD). RESULTS: The presence of Trametes Defined Medium (TDM) in the fermentation was required to obtain a significant COD reduction. Experiments in the batch reactor confirmed, in general, the predicted results of optimisation developed from Erlenmeyer batch assays. The T. versicolor culture remained active during 42 days of study in the SBR, providing approximately 80% of COD reduction. CONCLUSION: Trametes versicolor may be considered as very promising for the biological treatment of effluents from kraft pulp mills in an SBR system instead of the activated sludge mixed cultures traditionally used. Copyright © 2008 Society of Chemical Industry     

Smart phones and interactive reports leave traffic in the rearview mirror

To convey the dynamic information related to traffic conditions in various parts of a city, we propose an environment utilizing the technology of smart phones to provide information anywhere and anytime. Called ";The Interactive Traffic Beat Project,"; it uses a Web-based service to deliver this information to people through their cell phones at the right time so that valuable time can be saved and the chaos on the roads can be managed.     

Terahertz imaging: materials and methods

Terahertz (THz) imaging is rapidly developing. We present two new methods, based respectively on (a) a broadband thermal source (globar) and (b) a coherent, monochromatic source (optically-pumped THz laser). A room-temperature detector (Golay cell) is employed. Image quality is similar to that reported by others using more complex sources (quantum cascade lasers) and detectors (superconducting tunneling junctions).     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

Power sector development in India with CO2 emission targets: Effects of regional grid integration and the role of clean technologies

The power sector in India at present comprises of five separate regional electricity grids having practically no integrated operation in between them. This study analyses the utility planning, environmental and economical effects of integrated power sector development at the national level in which the regional electric grids are developed and operated as one integrated system. It also examines the effects of selected CO₂ emission reduction targets in the power sector and the role of renewable power generation technologies in India. The study shows that the integrated development and operation of the power system at the national level would reduce the total cost including fuel cost by 4912 million $, total capacity addition by 2784 MW, while the emission of CO₂, SO₂ and NO_x would be reduced by 231.6 (1.9%), 0.8 (0.9%), 0.4 (1.2%) million tons, respectively, during the planning horizon. Furthermore, the study shows that the expected unserved energy, one of the indices of generation system reliability, would decrease to 26 GWh under integrated national power system from 5158 GWh. As different levels of CO₂ emission reduction targets were imposed, there is a switching of generation from conventional coal plants to gas fired plants, clean coal technologies and nuclear based plants. As a result the capacity expansion cost has increased. It was found that wind power plant is most attractive and economical in the Indian perspective among the renewable options considered (Solar, wind and biomass). Copyright © 2003 John Wiley & Sons, Ltd.     

High-power 1.7–1.8 μm single-mode laser diodes

Separate confinement InGaAsP/InP laser heterostructures were grown by metalorganic-hydride vapor-phase epitaxy. High-power single-mode laser diodes of mesastripe design based on these heterostructures operate in a wavelength interval of 1.7–1.8 μm with a maximum continuous room temperature output power of 150 mW. The single-mode lasing regime is maintained up to an output power level of 100 mW.