6-in diameter InP single crystals grown by the hot-wall LEC method and the mirror wafers

6-in diameter Fe-doped semi-insulating InP single crystals have been grown by the hot-wall liquid encapsulated Czochralski method. This method has a quartz inner vessel to stabilize the thermal convection. Temperature gradient and solid-liquid interface shape can be controlled by a multizone heater system. The weight of grown crystal was 18 kg and the full length was 250 mm. The dislocation density was about 1/spl times/10/sup 5/ cm/sup -2/. The resistivity was more than 1/spl times/10/sup 7/ /spl Omega/cm and its uniformity was the same as the smaller diameter crystal. The conditions of wafer processing were optimized to improve the wafer flatness. The rolloff and the slope of the wafer surface could be reduced especially by the improvement of the polishing conditions. The typical total thickness variation was 3.3 /spl mu/m, and it was comparable to the GaAs wafer.     

Practical implementation and packaging technologies for alarge-scale ATM switching system

The practical implementation of a trial large-scale asynchronous transfer mode (ATM) switching system and its packaging technologies are described. The architecture of the ATM switching system is discussed with an emphasis on system scalability. A building block architecture in which switching capacity can be expanded in a modular fashion is introduced. The design of the ATM switching system, including the ATM switch element, is described. The implementation of the VLSIs for the ATM switch which realize a highly modular system is explained. Bit-slice techniques are effectively used to realize a high-speed switch element as a CMOS VLSI chipset. An edge-to-edge orthogonal packaging technique is also presented     

Production of a functionally graded artificial tooth root by unique sequence of processes

 A unique sequence of processes is used to produce a prototype of a functionally graded artificial tooth root: (1) Dry-jet spraying of the mixture of Ti and Al₂O₃ ultrafine particles (UFPs) produced by radio-frequency plasma onto the surface of a cylindrical Ti rod, where the composition of the UFPs is changed gradually in the outward radial direction from Ti to Al₂O₃; (2) Temperature-gradient sintering of the deposited composite, where the Ti – and the Al₂O₃– rich sides are heated simultaneously at about 1400 K and 1800 K, respectively; (3) Plasma spray coating of hydroxyapatite (HAP) onto the outermost Al₂O₃ surface of the sintered composite. The final product has compressive strength of more than 200 MPa and is durable against fatigue test of 10⁷ stress cycles at 1000 N. The adhesion strength between the Ti substrate and the Ti-Al₂O₃ functionally graded layer exceeds 65 MPa. No contamination with heavy metals is detected throughout the processes and biological cell growth is confirmed to occur on the HAP surface. With these mechanical and biochemical properties the composite produced here is considered to be highly suitable for an artificial tooth root. A series of processes developed here are expected to be applied to the production of various kinds of fine-grained functionally graded materials with complicated forms. Received: 13 October 1997 / Accepted: 27 October 1997     

Encapsulation of lead-free Sn/Zn/Bi solder alloy particles by coating with wax powder for improving oxidation resistance

An encapsulation treatment of lead-free Sn/Zn/Bi solder powder was investigated for improving the oxidation resistance. Sn-8mass%Zn-3mass%Bi alloy particles were coated with a wax (12-hydroxystearic acid) powder by means of a dry mechanical treatment method using a ball mill. In order to determine the optimum operating conditions of the ball mill in the wax-coating treatments, the compressive energy required for deforming a single Sn/Zn/Bi alloy particle was measured with an unconfined compression tester and the mechanical energy applied to the alloy particles in the ball mill was estimated using the results of the compression test. The optimum operating conditions were determined based on both the applied energy and the flowability of solder pastes, and the wax-coated alloy particles maintaining the spherical shape were obtained under the conditions. The wettability test and the solder balling test for the solder pastes containing the wax-coated alloy particles stored at room temperature in air were carried out to evaluate the oxidation resistance performance. The wax-coated alloy particles had an excellent wettability compared with the original alloy particles, and the oxidation resistance of the Sn/Zn/Bi solder powder was improved by the encapsulation treatment.     

Photocarrier generation in organic thin-film solar cells with an organic heterojunction

Photocurrent–voltage characteristics for organic solar cells with a heterojunction formed between copper phthalocyanine and a perylene derivative (or C₆₀) were studied. The photocurrent was observed under both reverse and forward biases. From the analysis of the photocurrent action spectra, the origin of the reverse photocurrent was attributed to the excitons formed in both the organic layers, whereas that of the forward photocurrent was attributed to the excitons formed in the perylene derivative (or C₆₀) layer. The photocurrent density under reverse bias increased at higher temperatures, suggesting that the charge recombination possibility was lowered at higher temperatures. On the basis of the time responses of the photocurrents observed after pulsed photoirradiation, the charge separation and transport processes are discussed.     

Isotropic photo-decomposition of spherical organic polymers on rutile TiO₂(110) surfaces

We observed the photo-decomposition process of polystyrene latex (PSL) spheres on a rutile TiO?(110) single crystal surface by using atomic force microscopy. During the decomposition process, both the height and width of the PSL spheres linearly decreased with the irradiation time in a similar way from the beginning, suggesting that the PSL spheres are isotropically decomposed. This indicates that the interface between the PSL spheres and the TiO? surface is not a dominant reaction site, as expected from normal photocatalytic reactions.     

Significance of the detection of staphylococcal enterotoxin A gene in low fat milk which caused a serious outbreak of food poisoning

In June 2000, there was a large-scale outbreak of food poisoning after consumption of Snow Brand low fat milk. In the evening of a day the incident made public, some cartons of low fat milk were brought to our laboratory for examination. Next day, we detected only staphylococcal enterotoxin (SE) A gene among SE (A-E) genes by PCR in left-over milk samples or samples from the same lots that patients had consumed. We presumed that the outbreak was caused by the intake of SEA. We subsequently confirmed the presence of SEA in these samples. To investigate the existence of SE (A-E) genes in milk, we examined 100 samples of commercial low fat milk and milk by PCR, but none of the genes was detected. We estimated the detection limit of SEA gene in low fat milk by PCR. Four strains of SEA-producing Staphylococcus aureus cultures were serially diluted in low fat milk. The SEA gene was detected at levels of 5.5 x 10(2) to 1.6 x 10(4) cfu/mL of S. aureus. These amounts of S. aureus are higher than the values in raw milk reported previously. Therefore we consider that SE genes in low fat milk should usually be undetectable by our PCR. This study shows that quick detection of SE genes by PCR is very helpful to analyze outbreaks, especially if no significant bacterium can be cultured.     

Generalized KYP lemma: unified frequency domain inequalities with design applications

The celebrated Kalman-Yakubovic/spl caron/-Popov (KYP) lemma establishes the equivalence between a frequency domain inequality (FDI) and a linear matrix inequality, and has played one of the most fundamental roles in systems and control theory. This paper first develops a necessary and sufficient condition for an S-procedure to be lossless, and uses the result to generalize the KYP lemma in two aspects-the frequency range and the class of systems-and to unify various existing versions by a single theorem. In particular, our result covers FDIs in finite frequency intervals for both continuous/discrete-time settings as opposed to the standard infinite frequency range. The class of systems for which FDIs are considered is no longer constrained to be proper, and nonproper transfer functions including polynomials can also be treated. We study implications of this generalization, and develop a proper interface between the basic result and various engineering applications. Specifically, it is shown that our result allows us to solve a certain class of system design problems with multiple specifications on the gain/phase properties in several frequency ranges. The method is illustrated by numerical design examples of digital filters and proportional-integral-derivative controllers.     

Chlorine auto-doping by chloride vapor phase epitaxial growth of InP

Chlorine auto-doping phenomenon was found for the first time in InP epitaxial growth by using a PCl₃/InP/H₂ system. Chlorine atoms act as a donor in the epitaxial layer and the carrier concentration is dependent on the facet of InP substrate. The carrier concentration of the InP layer on ( 111)B facet was over 10³ times higher than that on (111)A substrate.     

Simvastatin suppresses glomerular cell proliferation and macrophage infiltration in rats with mesangial proliferative nephritis

Inhibition of 3-hydro-3-methylglutaryl coenzyme A reductase inhibits the production of mevalonate and has been shown to suppress proliferation in many cell types. Therefore, 3-hydro-3-methylglutaryl coenzyme A reductase inhibitors may have a beneficial effect in glomerular disease, because glomerular cell proliferation is a central feature in the active glomerular injury. This study examines the effect of simvastatin on glomerular pathology in a rat mesangial proliferative glomerulonephritis (GN) induced by anti-thymocyte antibody (anti-Thy 1.1 GN). There was no difference in the degree of the antibody and complement-mediated initial injuries between simvastatin-treated and control GN rats. The most pronounced feature of simvastatin-treated GN was the suppression of the early glomerular cell proliferation. The proliferative activity was maximal at day 4 after disease induction (26.5+/-7.0 of proliferating cell nuclear antigen-positive cells/glomerulus); however, approximately 70% of proliferation was suppressed by simvastatin treatment. At day 4 after disease induction, simvastatin administration also decreased alpha-smooth muscle actin expression in the glomerulus, which is a marker for mesangial cell activation. Inhibition of monocyte/macrophage recruitment into glomeruli by simvastatin was also a prominent feature. There was a 30% decrease in the number of glomerular ED-1+ cells by simvastatin treatment at day 2 after disease induction. Furthermore, simvastatin remarkably suppressed subsequent mesangial matrix expansion and type IV collagen accumulation in glomeruli. We also found that the platelet-derived growth factor expression was reduced in simvastatin-treated nephritic rats, which might simply reflect the reduction in mesangial cell proliferation and mesangial cellularity. There was no significant difference in plasma cholesterol or triglyceride levels between simvastatin- and vehicle-treated nephritic rats at day 2 and day 4, which corresponded to the times when simvastatin treatment resulted in a reduction in mesangial cell proliferation. In conclusion, this is the first report to find that mesangial cell proliferation and matrix expansion have been blocked by simvastatin in vivo. The protective effect of simvastatin in the matrix expansion in anti-Thy1.1 GN was partly by inhibition of mesangial cell proliferation and monocyte/ macrophage recruitment into glomeruli, which were independent of a change in circulating lipids.