The effect of cyclic stress on the physical properties of a poly(dimethylsiloxane) elastomer

The dynamic creep behavior of a filled poly(dimethylsiloxane) elastomer was studied under cyclic stress. The stress level was chosen such that the increase in the internal temperature was small and that microcracks were not observed. This work has demonstrated that cyclic stress in combination with high temperature accelerates the degradation of the elastomer. The results suggest that because of the applied force, breaks in the load-bearing chains of the network occur. These breaks, while relieving the mechanical stress, create highly reactive ionic fragments. It is believed that because of the subsequent reactions of the ionic fragments, changes in the specific gravity, storage modulus, effective crosslink density, and length of the sample (creep) are observed. The observed decrease in the storage modulus is thought to occur because of the reaction of the ionic fragments with moisture, which results in the formation of silanol chain ends that reduce the effective crosslink density. The results also show that contrary to the prediction of the Boltzmann's Superposition Principle, the rate of creep is greatly enhanced when the sample is subjected to a sinusoidally varying dynamic load as compared to a comparable static load. The polymer weight loss was found to be linear with time and strongly dependent on the level of applied dynamic and static force. In addition, the weight loss and rate of creep were also found to be strongly dependent upon temperature.     

Response spectrum analysis of piping systems with elastic-plastic gap supports

A new seismic support device and its application in piping systems is described. The device, E-BAR (patented), can be cost effectively used for snubber replacement programs, mitigation of hydraulic transients, pipe whip and as a thermal stop. The device has pre-set gaps to allow free thermal movement. During a seismic or other dynamic load event, if the pipe movement exceeds the gap dimension, the device acts as an elastic or elastic-plastic restraint. The device also has a unique design feature for not exceeding the restraint force beyond a specified limit design value. To analyze piping systems with gap supports having elastic-plastic characteristics, modal analysis procedures for both response spectrum and time history methods are developed. The comparison of responses obtained from the procedures with nonlinear time history analysis and test results available in the literature shows excellent correlation. A pilot program conducted for snubber replacement with E-BARs demonstrates that the limit force feature of E-BAR makes them very attractive for snubber replacement. This is because a particular E-BAR with a specified limit design force can be selected, such that, the E-BAR replacing the snubber does not require any modifications be made to the existing support steel and hardware.     

A case study in SQA audits

Software quality assurance (SQA) audits are becoming a standard practice in corporations seeking to enter contractual relations with other organizations, or just evaluating their own state of readiness. This paper describes one approach to conducting SQA audits. Excerpts from reports of actual audits conducted on several organizations engaged in software development are used to show how an audit is conducted and what can be achieved through the auditing process. The paper is not meant to be a definitive answer or guide to doing SQA audits. Rather, it serves as an annotated case study of how SQA audits can be conducted with an emphasis on data gathering and reporting.Dr Paul W. Oman is an associate professor of computer science at the University of Idaho, and an independent software consultant who specializes in software analysis. He is the director of the Software Engineering Test Lab within the UI College of Engineering, where he conducts research in software development methods, CASE tools, and software maintainability issues. Oman has published over 50 articles and reports on software tools, software development, and computer science education. He has a PhD in computer science and is a member of the IEEE, IEEE Computer Society, and ACM.     

A high-current and high-temperature 6H-SiC thyristor

A 6H-SiC thyristor has been fabricated and characterized. A forward breakover voltage close to 100 V and a pulse switched current density of 5200 A/cm² have been demonstrated. The thyristor is shown to operate under pulse gate triggering for turn-on and turn-off, with a rise time of 43 ns and a fall time of less than 100 ns. The forward breakover voltage is found to decrease by only 4% when the operating temperature is increased from room temperature to 300°C. It is found that anode ohmic contact resistance dominates the device forward drop at high current densities     

Evaluation of the recombinant 38-kilodalton antigen of Mycobacterium tuberculosis as a potential immunodiagnostic reagent

The diagnosis of infection caused by Mycobacterium tuberculosis is of increased public health concern following increases in the number of cases in developed countries and major increases in developing countries associated with the spread of human immunodeficiency virus (HIV) infection. The specificity of purified protein derivative skin testing for the detection of infection is compromised by exposure to environmental mycobacteria. Examination of sputum detects the most infectious patients, but not those with extrapulmonary disease. The 38-kDa antigen of M. tuberculosis contains two M. tuberculosis-specific B-cell epitopes. We overexpressed the gene for this antigen in Escherichia coli and evaluated the recombinant product in in vitro assays of T-cell function and as a target for the antibody response in humans. The sensitivity and specificity of the antigen as a skin test reagent were also assessed in outbred guinea pigs. We found that 69% of healthy sensitized humans recognize the antigen in vitro, as manifested by both cell proliferation and the production of gamma interferon. Untreated patients initially have a lower frequency of response (38%); this recovers to 72% during therapy. A total of 292 patients (20 with HIV coinfection) and 58 controls were examined for production of antibody to the 38-kDa antigen by using a commercially available kit. The sensitivity of the test in comparison with that of culture was 72.6%, and the specificity was 94.9%. The antigen was also tested for its ability to induce skin reactions in outbred guinea pigs sensitized by various mycobacterial species. The antigen provoked significant skin reactions in M. tuberculosis-, M. bovis BCG-, and M. intracellulare-sensitized animals. The significance of these findings and the usefulness of this antigen in immunodiagnosis are discussed.