Friction and Wear Characteristics of Haynes 25, 188, and 214 Superalloys Against Hastelloy X up to 540 <Emphasis Type=Bold>°</Emphasis>C

As demand for more power increases, compression ratios, and operating temperatures keep rising. High speeds combined with high temperatures make turbomachinery sealing applications even more challenging. In order to confirm sufficient service life material pairs should be tested under conditions similar to engine operating conditions. This study presents high temperature friction and wear characteristics of cobalt/nickel superalloys, Haynes 25 (51Co–10Ni–20Cr–15W), Haynes 188 (39Co–22Ni–22Cr–14W), and Haynes 214 (75Ni–16Cr–3Fe–0.5Mn) sheets when rubbed against Hastelloy X (47Ni–22Cr–18Fe–9Mo) pins. Tests are conducted at 25, 200, 400, and 540 °C with a validated custom design linear reciprocating tribometer. Sliding speed and sliding distance are 1 Hz and 1.2 km, respectively. Friction coefficients are calculated with friction force data acquired from a load cell. Wear coefficients are calculated through weight loss measurements. Results indicate that Haynes 25 (H25) has the lowest friction coefficients at all test temperatures. Above 400 °C, H25 and Haynes 188 (H188) exhibit the best wear resistance. Protective cobalt oxide layers are formed on the H25 and H188 at 540 °C in addition to nickel, chrome, and tungsten oxides. Although, it has better oxidation resistance, Haynes 214 has relatively higher wear rates than other tested materials especially at low temperatures. However, its wear performance improves beyond 200 °C.     

A Novel Approach for Bolted T-Stub Connections

This paper reports an investigation into new connection types and their behaviors determined using full-scale experiments. T-shaped connections were created using the IPE standard profile. The aim of this study was to analyze the influence of T connections based on the IPE standard profile, height of beam to height of T-stub joint (H) of T-stub joints, and lengths (X) of T-stub joints on the behavior of steel connections, in order to provide the necessary data for improving Eurocode 3 and enable efficient use of residue IPE standard profiles and back to the consumption cycle. While the moment resistance values increased with an increase in H from H_min to H_max in model groups with X of 126 mm, and the energy dissipation increased with an increase in H from H_min to H_max and also with an increase in the lengths (X) of T-stub joints from 54 to 126 mm.     

Analysis of cross-country variations in the depth of European mortgage markets

To date, quantitative analysis on the depth of mortgage markets across a broad set of countries has been very limited. This paper uses a rich and balanced data set on 31 European countries to investigate the cross-country variations in the depth of mortgage markets during the period 2005–2012. The present paper might be accepted as the updated and enriched version of existing research for the European region in terms of the coverage of countries, historical data and the empirical analyses. Our empirical findings reveal that developed countries have sizeable residential mortgage markets and this is mainly associated with higher urbanization rates and stronger legal rights. One of the most notable results of this study is that, statistical significance of explanatory variables in modeling the depth of the mortgage markets depends heavily on both the variables, countries (regions) included in the models and the regression methodology used. Hence, we argue that strong conclusions based on such analyses should be avoided and the findings of previous research on the variations of the depth of mortgage markets should be carefully evaluated.     

Liquefaction hazard mapping in the city of Boumerdès,Northern Algeria

The city of Boumerdès, located in Northern Algeria, was badly affected during the May 21, 2003 Zemmouri (Mw = 6.8) earthquake where extensive liquefaction has been reported. The aim of this paper is to assess and to map the liquefaction potential for Boumerdès. We collected and used data from 154 boreholes, 10 down-hole tests, 56 standard penetrations tests (SPT), and inventory of 35 water level points. This data has been analyzed in the framework of geographical information systems (GIS). We assessed the liquefaction potential index (LPI) by considering a seismic hazard scenario corresponding to a_max = 0.48 g calculated, using a probabilistic approach, for a return period of 500 years. LPI values have been correlated to compile the liquefaction hazard map that indicates the quantitative characteristics of the liquefiable layers and the induced disruption probability area. Results show that the main part of the city of Boumerdès belongs to a low liquefaction potential area except for a narrow corridor along the Corso waterway, where the liquefaction potential is moderate to high. The obtained results are compatible with the geological, geotechnical and hydrogeological susceptibility to liquefaction of the area. The results also show a good agreement with the observations made after the May 21, 2003 Zemmouri earthquake. The obtained liquefaction hazard maps may serve as useful tools for land management and planning in the city of Boumerdès and as an example of liquefaction hazard assessment that may be applied in other populated cities in northern Algeria’s seismic prone areas.     

Nafion film/K(+)-exchanged glass optical waveguide sensor for BTX detection

An optical waveguide (OWG) sensor for the detection of BTX gases is reported. The highly sensitive element of this sensor was made by coating the copper Nafion film over a single-mode potassium ion exchanged glass OWG. We used the OWG sensor to detect toluene gas as a typical example BTX gas. The sensor exhibits a linear response to toluene in the range of 0.25-4250 ppm with response and recovery times less than 25 s. The sensor has a short response time, high sensitivity, and good reversibility.     

Relational approach in managing construction project safety: A social capital perspective

Existing initiatives in the management of construction project safety are largely based on normative compliance and error prevention, a risk management approach. Although advantageous, these approaches are not wholly successful in further lowering accident rates. A major limitation lies with the approaches’ lack of emphasis on the social and team processes inherent in construction project settings. We advance the enquiry by invoking the concept of social capital and project organisational processes, and their impacts on project safety performance. Because social capital is a primordial concept and affects project participants’ interactions, its impact on project safety performance is hypothesised to be indirect, i.e. the impact of social capital on safety performance is mediated by organisational processes in adaptation and cooperation. A questionnaire survey was conducted within Hong Kong construction industry to test the hypotheses. 376 usable responses were received and used for analyses. The results reveal that, while the structural dimension is not significant, the mediational thesis is generally supported with the cognitive and relational dimensions affecting project participants’ adaptation and cooperation, and the latter two processes affect safety performance. However, the cognitive dimension also directly affects safety performance. The implications of these results for project safety management are discussed.     

Accelerated transformation of brushite to octacalcium phosphate in new biomineralization media between 36.5 °C and 80 °C

This study investigated the hydrothermal transformation of brushite (dicalcium phosphate dihydrate, DCPD, CaHPO₄·2H₂O) into octacalcium phosphate (OCP, Ca₈(HPO₄)₂(PO₄)₄·5H₂O) in seven different newly developed biomineralization media, all inspired from the commercial DMEM solutions, over the temperature range of 36.5 °C to 90 °C with aging times varying between 1 h and 6 days. DCPD powders used in this study were synthesized in our laboratory by using a wet-chemical technique. DCPD was found to transform into OCP in the Ca²⁺, Mg²⁺, Na⁺, K⁺, HCO₃^?, Cl^? and H₂PO₄^? containing aqueous biomineralization media in less than 72 h at 36.5 °C, without stirring. The same medium was able to convert DCPD into OCP in about 2 h at 75–80 °C, again without a need for stirring. Samples were characterized by using powder X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM).     

The decolorization of C.I. Reactive Black 5 in aqueous solution by electrocoagulation using sacrificial iron electrodes

The removal of color from synthetic wastewater containing Reactive Black 5 was experimentally investigated using direct current electrocoagulation at iron electrodes. The effects of operational parameters such as current density, initial pH, electrolysis time, initial dye concentration and solution conductivity on color removal efficiency were investigated in this study. The optimum operating range for each of these operating variables was experimentally determined. The experimental results show that the color of Reactive Black 5 in the aqueous phase was removed effectively. Under the conditions of an initial dye concentration of 100 mg L(-1), initial pH of 5, current density of 4.575 mAcm(-2), salt concentration of 3000 mg L(-1), temperature of 20 degrees C, and interelectrode distance of 2.5 cm, the color removal efficiency reached 98.8%. Electrical energy consumption in the above conditions for the decolorization of the dye solution containing Reactive Black 5 was 4.96 kWh/kg dye. Results show that the first-order rate equation provides the best correlation for the decolorization rate of Reactive Black 5.     

Integrated microfluidic system enabling (bio)chemical reactions with on-line MALDI-TOF mass spectrometry

A continuous flow micro total analysis system (micro-TAS) consisting of an on-chip microfluidic device connected to a matrix assisted laser desorption ionization [MALDI] time-of-flight [TOF] mass spectrometer (MS) as an analytical screening system is presented. Reaction microchannels and inlet/outlet reservoirs were fabricated by powderblasting on glass wafers that were then bonded to silicon substrates. The novel lab-on-a-chip was realized by integrating the microdevice with a MALDI-TOFMS standard sample plate used as carrier to get the microfluidic device in the MALDI instrument. A novel pressure-driven pumping mechanism using the vacuum of the instrument as a driving force induces flow in the reaction microchannel in a self-activating way. Organic syntheses as well as biochemical reactions are carried out entirely inside the MALDI-MS ionization vacuum chamber and analyzed on-line by MALDI-TOFMS in real time. The effectiveness of the micro-TAS system has been successfully demonstrated with several examples of (bio)chemical reactions.