Parasitic bipolar gain in fully depleted n-channel SOI MOSFET's

Fully depleted SOI MOSFET's include an inherent parasitic lateral bipolar structure with a floating base. We present here the first complete physically based explanation of the bipolar gain mechanism, and its dependence on bias and technological parameters. A simple, one-dimensional physical model, with no fitting parameters, is constructed, and is shown to agree well with simulations and measurements performed on a new type of SOI MOSFET structure. It is shown that parameters which affect the gain, such as SOI layer thickness, body doping concentration and gate and drain voltages, do so primarily by affecting the concentration of holes in the body region. Thus, current gain falls dramatically with increasing drain voltage due to the associated impact ionization driven increase in the hole concentration. Gummel plots of this parasitic bipolar indicate an apparent ideality factor of 0.5 for the hole current, due to the body hole concentration's dependence on drain voltage     

Fabrication of low-loss IR-transmitting Ge30As10Se30Te30 glass fibers

Improved purification and processing techniques have been utilized to fabricate Ge₃₀As₁₀Se₃₀Te₃₀ glass fibers with a minimum loss of O.11 dB/m at 6.6 μm. This is the lowest loss reported for any telluride glass fiber in the infrared region. Furthermore, the fibers exhibit less than 1 dB/m loss between 5.25 and 9.5 μm     

Preparation and characterization of transparent ZnO/epoxy nanocomposites with high-UV shielding efficiency

Transparent ZnO/epoxy nanocomposites with high-UV shielding efficiency were reported in this paper. First, zinc oxide (ZnO) precursor was synthesized via the homogeneous precipitation method and ZnO nanoparticles were then made by calcination of the precursor at different temperature. The structural properties of the as-prepared ZnO nanoparticles were studied in detail using thermogravimetry (TGA), differential thermal analysis (DTA), X-ray diffractometer (XRD), Fourier transform infrared spectrometer (FT-IR) and transmission electron microscopy (TEM), respectively. Transparent ZnO/epoxy nanocomposites were subsequently prepared from transparent epoxy (EP-400) and as-prepared ZnO nanoparticles via in situ polymerization. Optical properties of ZnO/epoxy nanocomposites, namely visible light transparency and UV light shielding efficiency, were studied using an ultraviolet-visible (UV-vis) spectrophotometer. The optical properties of the as-obtained nanocomposites were shown to depend on ZnO particle size and content. The nanocomposite containing a very low content (0.07% in weight) of ZnO nanoparticles with an average particle size of 26.7 nm after calcination at 350 °C possessed the most optimal optical properties, namely high-visible light transparency and high-UV light shielding efficiency, that are desirable for many important applications.     

Digital filter bank design quadratic-constrained formulation

Formulate the filter bank design problem as an quadratic-constrained least-squares minimization problem. The solution of the minimization problem converges very quickly since the cost function as well as the constraints are quadratic functions with respect to the unknown parameters. The formulations of the perfect-reconstruction cosine-modulated filter bank, of the near-perfect-reconstruction pseudo-QMF bank, and of the two-channel biorthogonal linear-phase filter bank are derived using the proposed approach. Compared with other design methods, the proposed technique yields PR filter banks with much higher stopband attenuation. The proposed technique can also be extended to design multidimensional filter banks     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Shortest path algorithms: A computational study with the C programming language

The main purpose of this study is to evaluate the computational efficiency of algorithms for calculating shortest paths when they are correctly coded by using the C programming language. The eight algorithms that we selected for this experiment are the most efficient, either measured in terms of worst-case bounds or marked as such from previous computational studies; they include the redistributive heap algorithm. We suggest computer implementations that use the full power of C. In particular, the network representation and the various data structures used to keep the scan eligible list may be managed by using only additions and no multiplications, while it is not possible with FORTRAN. These capabilities, unique to C, yield several interesting conclusions: one may expect to speed up a shortest path algorithm by a factor of 20%; in some cases, this factor may reach 30%. Interestingly, the level of programming difficulty required to achieve these benefits is not greater than that required by implementations using arrays.     

Fabrication of Arsenic Sulfide Optical Fiber with Low Hydrogen Impurities

Arsenic sulfide glass optical fibers typically possess extrinsic absorption bands in the infrared wavelength region associated with residual hydrogen and oxygen related impurities, despite using purified precursors. We report a purification process based on the addition of tellurium tetrachloride (TeCl₄) to the glass. During melting, the chlorine from TeCl₄ reacts with the hydrogen impurities to produce volatile products (e.g., HCl) that can be removed by subsequent dynamic distillation. The processing conditions have been modified accordingly to produce optical fibers with significantly reduced loss due to hydrogen sulfide impurity content (1.5 dB/m).     

On the Cutoff Wavelength of Rectangular-Shaped Microshield Line by Edge Element Method

In this paper, the cutoff characteristic of rectangular-shaped microshield transmission line has been analysed by edge element method. Dependence of cutoff wavelengths on the thickness of metallic signal strip, dielectric constant of dielectric substrate and the width of the rectangular-shaped ground conductor are presented in tabular form. Numerical results in this paper have important values in design of rectangular-shaped microshield lines in microwave and millimeter wave integrated circuits.     

Identification of Factors Affecting Preservative Efficacy and Chemical Stability of Lamivudine Oral Solution Through Statistical Experimental Design

To identify factors affecting the chemical stability and preservative efficacy of lamivudine oral liquid formulations, an optimization study using a central composite design was performed. In this design, five factors, each at three levels, were investigated: pH (4.5, 5.5, and 73, sucrose (5%, 20%. and 50% w/v), propylene glycol (0% 2%, and 5% w/v), glycerin (4% 8%, and 12% w/v). and EDTA (0.100. 0.175, and 0.250 mg/mL). All formulations contained a constant concentration of lamivudine, parabens, and artificial strawberry and banana flavors. All formulations were evaluated for preservative effectiveness against USP and BP standards and for chemical stability at 30°C and 40°C for three months. All formulations were effective against bacteria and yeasts, but indicated reduced preservative effectiveness against the mold Aspergillus niger. Preservative effectiveness improved with increasing pH (4.5 to 7.5) and to a lesser extent with increasing EDTA concentration (0.100 to 0.250 mg/mL). Increasing glycerin concentration (4% to 12% w/v) slightly decreased preservative effectiveness. Over the concentration ranges tested, no change in preservative effectiveness was noted with concentration changes in sucrose or propylene glycol. The pH was the main factor influencing the chemical stability of the drug and preservatives in this study. Lamivudine chemical stability increased with increasing pH from 4.5 to 7.5. Methyl and propylparaben showed extensive degradation at pH 7.5.