Preparation of novel 2-(2-oxo-2H-chromen-4-yl)-3- arylthiazolidin-4-one derivatives using an efficient ionic liquid catalyst

An eco-friendly procedure for synthesis of 2-(2-oxo-2H-chromen-4-yl)-3-arylthiazolidin-4-one derivatives by three-component reaction of 2-oxo-2H-chromene-4-carbaldehydes, aromatic amines and thioglycolic acid, with tetramethylbutane-1,4-diammonium acetate as a low-cost ionic liquid catalyst under reflux condition is described. The use of an ionic liquid as a catalyst has the advantages of high yields, short reaction time and environmentally friendly reaction media.     

Effects of dynamic vulcanization on tensile,morphological, and swelling properties of poly(vinyl chloride) (PVC)/epoxidized natural rubber (ENR)/(Kenaf core powder) composites

The effects of dynamic vulcanization on properties of poly(vinyl chloride) (PVC)/epoxidized natural rubber (ENR)/(kenaf core powder) composite were studied. Tensile properties indicated that the strength, elongation at break, and Young's modulus of the composites exhibited an increase for samples with dynamic vulcanization. Morphological analysis using scanning electron microscopy showed the interaction between ENR and PVC. There was no bonding between kenaf core powder and the PVC/ENR matrix owing to the different polarity of both components. Filler agglomerates increased, which leads to an increase of filler‐filler interaction and poor dispersion. Furthermore, swelling index indicated that the composite with dynamic vulcanization shows lower absorption of tolune compared with composites without dynamic vulcanization. J. VINYL ADDIT. TECHNOL., 22:206–212, 2016. © 2014 Society of Plastics Engineers     

A modern congestion pricing policy for urban traffic: subsidy plus toll

Railway Engineering Science - Congestion pricing is seen as an effective policy to address traffic congestion. In such policies where money, people and authorities are involved, the success...     

Hot Corrosion Behavior and Microstructural Change of Al-Gradient CoNiCrAlYSi Coatings, Produced by LVPS and Diffusional Processes

Conventional and gradient CoNiCrAlYSi coatings were produced by using low vacuum plasma spray and an additional step of diffusional over aluminizing (pack cementation) techniques on an Inconel-738 substrate. Hot corrosion of these coatings was investigated using Na₂SO₄–20wt%NaVO₃ molten salt at 880?°C for 800?h. Hot corrosion rate was determined by measuring the weight gain of the specimens at regular intervals for a duration of 20?h. X-ray diffraction, field emission scanning electron microscopy and electron probe micro analysis techniques were used to determine the nature of phases, investigation of the thermally grown oxide, examination of the surface attack and determination of the elemental distribution. The gradient coating showed better performance by re-healing alumina scale due to its possession of more β phase as Al reservoir. Results indicated that pack cementation process caused an increase in amount of aluminum-rich β phase and better hot corrosion properties of gradient coatings owing to the Al enrichment in the outer layer and rapid formation of protective oxide on the surface.     

Friction and compression characteristics of chickpea flour and components

Chemical composition and selected physical properties of chickpea flour, the starch fraction and the protein fraction were determined. Coefficient of internal friction, coefficient of external friction (on steel, concrete, Teflon and polypropylene), cohesion and adhesion of samples were measured. Chickpea flour and starch fraction had the highest coefficient of internal friction and cohesion, respectively. The coefficient of external friction of chickpea flour and components on concrete was markedly higher than other surfaces. The starch fraction had the highest compressibility and asymptotic modulus at most of the preset loads. The compressibility and asymptotic modulus increased with porosity. Chickpea flour with the lowest porosity had the lowest asymptotic modulus. All samples underwent particle rearrangement during compression.     

Preparation and characterization of poly(vinyl alcohol)/gum tragacanth/cellulose nanocomposite film

The effects of gum tragacanth obtained from two species of Astragalus Gossypinus (GT-G) and A. Parrowianus (GT-P) at two levels of 10% and 30% combined with cellulose nanofibers (CNF; 5%) on the physico-mechanical and structural properties of polyvinyl alcohol (PVA) nanocomposite film were investigated in this study. The water solubility and water vapor permeability of the films decreased with increasing the content of both gums, especially in the film containing 30% GT-P. The highest values of the tensile strength (39.3 MPa) and elongation at break (445%) belonged to the treatment containing 10% GT-P (90/10P/0). The FTIR and DSC analyses confirmed good interactions between GT and PVA in the 90/10P/0 treatment. SEM images indicated the dense structure of this film as the optimum treatment. Although the presence of CNF in the films containing GT-G improved some properties, especially the Young modulus, it impaired all the functional properties of nanocomposite GT-P film.     

Effect of Melt-to-Solid Insert Volume Ratio on Mg/Al Dissimilar Metals Bonding

Compound casting is used as a process to join various similar and dissimilar metallic couples. The ratio of melt-to-solid volume is one of the main factors that can affect the contact time between melt and the solid insert. In this investigation, magnesium and aluminum metals (magnesium as the cast metal and aluminum as the solid insert) having melt-to-solid volume ratios (V _m/V _s) of 1.25, 3, and 5.25 were successfully bonded via compound casting. Results demonstrated that by increasing the ratio of V _m/V _s from 1.25 to 5.25, the thickness of the reaction interface between Al and Mg varies within the range of 200 to 1800 μm. X-ray diffraction, scanning electron microscopy, and Vickers microhardness study of the bonding of these two metals showed that the interface consisted of three separate sub-layers within reaction layer. These sub-layers had higher hardness than those of the Al and Mg bulk metals. In all specimens, composition of the sub-layer adjacent to Al (layer I) was Al₃Mg₂ and that adjacent to Mg (layer III) was Al₁₂Mg₁₇/(Mg) eutectic structure. The intermediate layer composition (layer II) in specimens with volume ratio of 1.25 and 3 was a single-phase Al₁₂Mg₁₇, while for the case of volume ratio 5.25 this sub-layer consisted of Al₁₂Mg₁₇/(Mg) eutectic dispersed in Al₁₂Mg₁₇ intermetallic. The results of this research showed that in low melt/solid volume ratios, diffusion-reaction was the dominant mechanism for formation of Al-Mg intermetallic. However, when V _m/V _s and the melt/solid insert contact time increased, the dominant mechanism of Al-Mg intermetallics changed to fusion-solidification due to increase in surface melting of the solid insert. Also the results of push-out tests showed that shear strengths of the interface decrease from 27.1 to 15.1 and 8.3 MPa for the Al/Mg couples prepared at 1.25, 3, and 5.25 V _m/V _s respectively.     

Ferroelectric,dielectric, magnetic,structural and photocatalytic properties of Co and Fe doped LaCrO3 perovskite synthesized via micro-emulsion route

In the present investigation, La_1-xCo_xCr_1-yFe_yO₃ (x,y = 0.0, 0.12, 0.36, 0.60) perovskite was fabricated via a facile micro-emulsion route. The synthesized perovskites were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) techniques to examine the effect of Co and Fe ions on the physico-chemical properties. The ferroelectric, dielectric, and magnetic properties of La_1-xCo_xCr_1-yFe_yO₃ were changed significantly as a function of dopants contents (Co and Fe ions). Outcomes revealed that the dielectric, ferroelectric and magnetic properties of LaCrO₃ perovskite can be tuned significantly via Co and Fe doping and La_0.40Co_0.60Cr_0.40Fe_0.60O₃ have potential for photocatalytic dye removal under (visible) light expoure. The photocatalytic activity (PCA) of the pristine LaCrO₃ and La_0.40Co_0.60Cr_0.40Fe_0.60O₃ photocatalyst was evaluated under (visible) light irradiation for crystal violet (CV) dye. Experimental results revealed that La_0.40Co_0.60Cr_0.40Fe_0.60O₃ photocatalyst degrdae almost 77.21% CV dye with the rate constant value of 0.01475 min^?1. In the presence of isopropyl alcohol (IPA) scavenger, the PCA of the La_0.40Co_0.60Cr_0.40Fe_0.60O₃ photocatalyst and rate constant value of the photocatalytic reaction decreased to 32.5% and 0.00491 min^?1, suggesting the superoxide as main active specie. Results revealed that Co and Fe doping doped material is efficient for photocatalytic presentations under solar light expoure.     

Application of Compressible Volume of Fluid Model in Simulating the Impact and Solidification of Hollow Spherical ZrO<Subscript>2</Subscript> Droplet on a Surface

Applications of hollow spherical particles in thermal spraying process have been developed in recent years, accompanied by attempts in the form of experimental and numerical studies to better understand the process of impact of a hollow droplet on a surface. During such process, volume and density of the trapped gas inside droplet change. The numerical models should be able to simulate such changes and their consequent effects. The aim of this study is to numerically simulate the impact of a hollow ZrO₂ droplet on a flat surface using the volume of fluid technique for compressible flows. An open-source, finite-volume-based CFD code was used to perform the simulations, where appropriate subprograms were added to handle the studied cases. Simulation results were compared with the available experimental data. Results showed that at high impact velocities (U ₀ > 100 m/s), the compression of trapped gas inside droplet played a significant role in the impact dynamics. In such velocities, the droplet splashed explosively. Compressibility effects result in a more porous splat, compared to the corresponding incompressible model. Moreover, the compressible model predicted a higher spread factor than the incompressible model, due to planetary structure of the splat.     

Using backward elimination with a new model order reduction algorithm to select best double mixture model for document clustering

Probabilistic latent semantic analysis (PLSA) is a double structure mixture model which has got a wide application in text and web mining. This method is capable of establishing hidden semantic relations among the observed features, using a number of latent variables. In this approach, the selection of the correct number of latent variables is critical. In the most of the previous researches, the number of latent topics was selected based on the number of invoked classes. This paper presents a method, based on backward elimination approach, which is capable of unsupervised order selection in PLSA. This method starts with a model having a number of components more than the needed value, and then prunes the mixtures to reach their optimum size. During the elimination process, proper selection of some latent variables which must be deleted is the most essential problem, and its relation to the final performance of the pruned model is straightforward. To treat this problem, we introduce a new combined pruning method which selects the best options for removal, while keeping a low computational cost, at all. We conducted some experiments on two datasets from Reuters-21578 corpus. The obtained results show that this algorithm leads to an optimized number of latent variables and in turn achieves better clustering performance compared to the conventional model selection methods. It also shows superiority over the case in which a PLSA model with a fixed number of latent variables, equal to the real number of clusters, is exploited.