DX centers in AlxGa1-xAs bulk alloy,AlAs/GaAs ordered,and disordered superlattices

Properties of theDX centers in Al_0.5Ga_0.5As bulk alloy (b-AL), (AlAs)₂ (GaSa)₂ ordered superlattice (o-SL) and (AlAs) _m (GaAs) _n disordered superlattice (d-SL) (m = 1, 2, 3,n = 1, 2, 3) with the same macroscopic composition were measured and compared. By deconvolution of deep level transient spectroscopy (DLTS) spectrum due to theDX center, we have found a decrease in the number of separate peaks in DLTS spectrum in an intentionally atomic ordered arrangement. Visiting Scholar of the Japan Society for the Promotion of Science. On leave from Department of Electrical Engineering, San Jose State University, San Jose, California 95192-0084, USA.     

Band Gaps of Na2C60 and K4C60

respectively.     

Effects of Environmental Temperature and Compression Energy on Polymorphic Transformation During Tabletting

The effects of temperature on the polymorphic transformation and the compression of chlorpropamlde forms A and C during tabletting were investigated by X-ray diffractometry. The X-ray diffraction profiles of the sample powders deagglomerated after compression were recorded to calculate the degree of polymorphic transformation. A single punch eccentric tabletting machine equipped with two load cells (upper and lower punches) and with a noncontact displacement transducer was used to measure the compression stress, energy and distance between punches. A heater and a liquid nitrogen pool were mounted on the die of the tabletting machine, and the die temperature was controlled with a thermocontroller. Two types of compression methods, multi-tabletting at room temperature and single tabletting at 0-45°C, were used in the present study. In the first method, the stable form A or metastable form C was loaded in to the die and the sample was compressed with a compression stress of 196 MPa. Compression was repeated from 1 to 30 times. The results for forms A and C suggested that both forms were mutually transformed, and that the content of forms A and C reached equilibrium above 100 J/g of compression energy after more than 10-times compression. After 30-times compression, the content of A, C, and the noncrystalline solid form were almost constant at about 45%, 25% and 30%, respectively. The compression energy was estimated to be 500-600 J/g. In the second method, single tabletting at 0° and 45°C, the amount of form C transformed from form A at 45°C was about two times larger than that at 0°C at the same compression energy. The amount of form A transformed from form C at 45°C was almost the same as that transformed at 0°C. This suggests that the mechanochemical stability of form A was affected by compression temperature, while that of form C was independent of temperature. The crushing strength (CS) of from A tablet was about two times higher than that of form C even at the same porosity. The relationships between log (CS) of form A tablets compressed at 0 or 45°C and porosity showed straight lines with the same slope, but the slope for form C tablets compressed at 45°C was smaller than that for those compression at 0°C. From these results it appears that the transformation mechanism of forms A and C during compression was as follows: Form A or C was converted to a noncrystalline solid by mechanical energy, and then the solid was transformed into form A or C. The transformation of every form was affected by the environmental temperature.     

A far-infrared spectroscopic study of low temperature soft phonon mode in Tris-Sarcosine Calcium Chloride(TSCC)

Temperature dependences of the soft phonon frequency and the damping constant in Tris-Sarcosine Calcium Chloride (TSCC) single crystal have been investigated between 5K and 100K by using a Fourier-transform far-infrared spectrometer. It has been observed that the soft phonon frequency decreases gradually and the damping constant increases as the transition temperature is approached from below The damping constant varies from 7cm^-1 a 90K to less than 0.5cm^-1 at 5K. It has been found that the damping constant is approximately proportional to temperature below about 60K.     

Flexural properties of moldings of rigid polyurethane made by reaction injection molding

Flexural properties of moldings made by Reaction Injection Molding (RIM), which are structural foams consisting of high density skin and low density core, were investigated by three-point bending tests. Two failure modes were observed in bending tests of the moldings made by RIM, and they are classified as follows according to the density ratio of skin layer to core layer: the opposite side of the skin layer to which load was subjected failed by tensile stress: and the same side of the skin layer to which load was subjected failed by compressive stress, causing wrinkling or buckling. Then the conventional composite beam theory was applied to the former failure mode and Hoff s buckling theory to the latter, and equations were derived to predict the flexural properties of the structural foams, which involved buckling from the flexural properties of solid construction. In addition, it has been shown that there exists a density distribution that maximizes the flexural strength of the moldings made by RIM with a given overall density. The results obtained here should be useful to the optimum structural design of moldings made by RIM.     

Importance of nuclear generation in the struggles to reduce CO2 emission at Kansai Electric Power Co.

It has been pointed out in recent years that the potential impacts of global warming has been becoming more and more serious because of the rapid increase of anthropogenic CO₂ emission.

Japan's annual CO₂ emissions (fiscal 1994) amounted to 343 million tons of carbon. Although CO₂ emissions caused by fossil-fuel power generation accounted for 29.4% of total, on a sector basis, those directly from the energy conversion sector accounted for only 7.7%. Most CO₂ emissions (21.7% of total) resulted from electric power use in the industrial, commercial and domestic sectors. Thus, the reduction of CO₂ emissions caused by the use of electricity is a nationwide subject.

Understanding that both supply side and demand side approaches are necessary, Kansai Electric has been deploying “New ERA Strategy” as a comprehensive strategy to seek a potential for CO₂ reduction more broadly and deeply. Among a number of action items are the promotion of nuclear power generation, and improvement of overall energy efficiency, besides such demand side measures as leveling off the peak load.

The effectiveness of action items of the New ERA Strategy was evaluated in terms of CO₂ reduction. As a result, estimated CO₂ reduction related to nuclear power amounted to 88% of the total for fiscal 1995 in comparison with 1990, and that expected in 2000 is 84%. These results reconfirm that nuclear power is always the key to practical CO₂ reduction at present and in the future.

Comparison with candidate technology alternatives revealed that photovoltaic power generation needed 7 times greater rated capacity and 280 times larger area than nuclear power, so it is not realistic as a central power station alternative. The comparison also clarified that if wind power stations were constructed at all feasible sites in the Kansai region, they would not be a viable alternative to a single nuclear unit from CO₂ reduction viewpoint.     

Vivid image projection system using e‐Paper active screen

Projected image on a screen is not always vivid enough when it is projected in a bright room. We generally have to choose either vivid image in a dark room or dull image in a bright room. We have suggested a new projection system which can realize high contrast image projection in a bright room. It is consisted of electronic paper screen, projector, and light‐emitting diode room light. The electronic paper (e‐Paper) screen alternates its whole surface white/black with 120 Hz. Room lights are controlled with the same frequency of 120 Hz with the opposite phase as that of the e‐Paper screen. We have confirmed that our new system has achieved higher contrast than the conventional projection system and also enough readability of paper documents in the room simultaneously. We have thus confirmed that our new system can bring an ideal condition, for audience, which can realize a vivid image projection in a bright room.     

A novel quarter‐wave retardation film for improving viewing angle properties in time‐sequential stereoscopic 3D‐LCDs

We have successfully developed a quarter‐wave retardation film (QWF) for wide viewing angle 3D liquid crystal displays (3D‐LCDs) that provides high luminance, low crosstalk, low color change, and low head‐tilt‐angle dependency. It was found that the out‐of‐plane retardation (Rth) of the QWF in the LCD needs to be close to 0 nm in order to improve the 3D display properties at an off‐axis position and that the in‐plane retardation (Re) needs to be adjusted from 120 to 130 nm to achieve low color change with head tilting. We adopted a coating process for making our QWF because of its potential for retardation control. 3D‐LCDs with this QWF whose Rth was nearly zero had high performance and allowed off‐axis other than on‐axis.