The influence of NaCl and CO2 on the atmospheric corrosion of magnesium alloy AZ91

The influence of NaCl and CO₂ on the atmospheric corrosion of magnesium alloy AZ91 is studied in the laboratory. Samples were exposed under carefully controlled air and flow conditions; the relative humidity was 95%, the temperature was 22.0°C and the concentration of CO₂ was < 1 ppm or 350 ppm. Different amounts of sodium chloride (0–70 μg/cm²) were added before exposure. The corrosion products were analyzed by gravimetry, ion chromatography, X‐ray diffraction and scanning electron microscopy. Mass gain and metal loss results are reported. The combination of high humidity and NaCl is very corrosive towards AZ91. However, the NaCl‐induced corrosion is inhibited by ambient concentrations of CO₂. Exposure in the absence of CO₂ gives rise to heavy pitting, with brucite, Mg(OH)₂, being the dominant corrosion product. In the presence of CO₂ a layer of hydrated magnesium hydroxy carbonate, Mg₅(CO₃)₄(OH)₂ · 5 H₂O forms. A tentative corrosion mechanism is presented that explains the behavior in the two environments.     

Synthesis and characterization of novel diimide–dinaphthols and resulting poly(urethane–imide)s

Novel diols containing imide groups were prepared via condensation of aromatic dianhydrides with 5‐amino‐1‐naphthol. The diimide–dinaphthols prepared were characterized by conventional methods and used to synthesize new poly(urethane–imide)s (PUIs). All the polymers were characterized and their physical properties, such as solubility, solution viscosity, thermal stability, and thermal behaviour were studied. The polymers obtained showed more thermal stability than typical polyurethanes because of the presence of the imide groups. Copyright © 2003 Society of Chemical Industry     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

刊首语

今天本刊以全新的面貌呈现于广大读者面前,这是杂志成长过程中的羽化新生。2006年9月,经国家新闻出版总署批准,《中国农村水电及电气化》杂志正式更名为《中国水能及电气化》。作为水利部主管的行业期刊,杂志的更名是主办单位水利部水电局贯彻落实科学发展观和《可再生能源法》     

A Practical Method to Derive Sample Temperature during Nonisothermal Coupled Thermogravimetry Analysis and Differential Scanning Calorimetry Experiments

Nonisothermal thermogravimetry differential scanning calorimetry (TG‐DSC) mounting is intensively used for the determination of kinetic parameters and reaction heat along the chemical transformation of a solid. Nevertheless, when tests are performed with heating rates as high as those encountered in industrial processes, e.g., several tens of K min^–1, there is great uncertainty in the knowledge of the exact sample temperature. In this work, a method to derive a simple mathematical expression is proposed and fully described in order to calculate the real sample temperature throughout a temperature‐ramped test on a commercial apparatus. The furnace temperature and the heat flow signals were used, together with the crucible specific heat and the heating rate. A number of validation tests were performed to derive similar reaction rates for a reference. First‐order kinetic reactions were presented and reconciled over a large range of heating rates from 3 to 50 K min^–1.     

Effect of polymerization conditions on o‐phenylenediamine and o‐phenetidine oxidative copolymers

A series of new o‐phenylenediamine (OPD)/o‐phenetidine (PHT) copolymers with partly phenazine‐like structures has been successfully synthesized at three polymerization temperatures by chemically oxidative polymerization in four different polymerization media. The molecular structures and properties of the resulting OPD/PHT polymers were investigated by IR, UV–vis and high‐resolution ¹H NMR spectroscopies, and DSC, in order to ascertain the effect of reaction temperature, comonomer ratio and acid medium. The copolymerization mechanism of OPD with PHT monomers has been proposed. It is found that the statistical OPD/PHT copolymer obtained at a temperature of 118 °C has a higher degree of polymerization than that obtained at 12–17 °C. The OPD content in the copolymers calculated from NMR spectroscopic analysis is higher than that in the feed OPD content, whereas the OPD content calculated from element analysis is slightly lower than the feed OPD content. It can be predicted that denitrogenation takes place in the OPD units during the polymerization process at OPD/PHT molar ratios of 90/10 and 100/0. These OPD/PHT copolymers exhibit a much better solubility than the OPD homopolymer, hence suggesting an incorporation of PHT units into the phenazine structure of the homopolymer. The thermal behavior of the copolymers was also studied. Copyright © 2004 Society of Chemical Industry     

Oil Spill Cleanup from Sea Water by Sorbent Materials

Three sorbents were compared in order to determine their potential for oil spill cleanup. Polypropylene nonwoven web, rice hull, and bagasse with two different particle sizes were evaluated in terms of oil sorption capacities and oil recovery efficiencies. Polypropylene can sorb almost 7 to 9 times its weight from different oils. Bagasse, 18 to 45 mesh size, follows polypropylene as the second sorbent in oil spill cleanup. Bagasse, 14 to 18 mesh size, and rice hull have comparable oil sorption capacities, which are lower than those of the two former sorbents. It was found that oil viscosity plays an important role in oil sorption by sorbents. All adsorbents used in this work could remove the oil from the surface of the water preferentially.     

Magnetic Resonance Visualisation of Flow and Pore Structure in Packed Beds with Low Aspect Ratio

Different NMR techniques were combined to obtain the structure and velocity information for a systematic investigation of fixed beds with low aspect ratio (tube diameter to particle diamter, d_t/d_p) in the range 1.4 to 32. The structure of the void space was determined for a variety of packed beds of glass beads or regular and irregular porous pellets by magnetic resonance imaging (MRI). Based on the images the radial distribution of the voids within the bed was obtained. Ordering effects were found even for non‐spherical and polydisperse particles, and a maximum of the fluid density near the tube wall was confirmed for all pellet geometries and sizes. By combining MRI with velocity encoding, velocity profiles and distributions of flow velocity components of a single fluid phase through packed beds have been acquired. The radial velocity distribution follows an oscillatory pattern which largely reflects the ordering of the particles, which can be accessed from the density distribution of the interparticle fluid. Maximum velocities of up to four times the average value were found to occur near the tube wall. This wall effect was observed for all but the smallest particles, where the aspect ratio was d_t/d_p = 32. Moreover, a visualisation of flow pattern in the presence of packed particles was achieved by using a tagging technique, and the stationary flow field could be identified for an experimental time of several hours.