Velocity and turbulence measurements in a cylindrical bath subject to centric bottom gas injection

Laser Doppler velocimeter (LDV) measurements were made to clarify the fluid flow behavior in a bath subject to centric bottom gas injection. Correlations of the axial mean velocity and turbulence components in the gas-liquid two-phase flow region,i.e., in the bubbling jet region, were proposed as functions of the inner diameter of nozzle, gas flow rate, and densities of gas and liquid. Measured values of the flow rate, momentum, and kinetic energy of water rising upward were approximated satisfactorily by these empirical correlations. In addition, the Reynolds shear stress was calculated and compared with measured values. Formerly Graduate Student, Osaka University,     

Deformation behavior of polytetrafluoroethylene films under tensile stress at various temperatures

Deformation behavior of polytetrafluoroethylene (PTFE) films was investigated by thermomechanical analysis (TMA) under various tensile stresses (σ) up to 1.15 MPa in the temperature range from room temperature to 360°C. In the heating process above σ ≈ 0.25 MPa, a contraction of the PTFE film occurs in the melting temperature region. In the cooling process above σ ≈ 0.05 MPa, an elongation occurs in the crystallization temperature region, and above σ ≈ 0.5 MPa, it reaches 20–30% of the original length of the film. The PTFE films in the melt state above σ ≈ 0.5 MPa contract with increasing temperature up to 360°C and elongate with decreasing temperature. For the films that underwent deformation in the TMA, the crystalline orientation and the surface morphology were investigated by wide-angle X-ray diffraction and scanning electron microscopy, respectively. The degree of crystalline orientation in the deformed films increases with increasing σ and approaches a plateau at σ ≈ 0.4 MPa. On the surface of the deformed films, alignment of the bands and deformation of granules, which are formed by heat treatment above the melting point, are observed. © 1994 John Wiley & Sons, Inc.     

Influences of electroosmotic flows in nanopillar chips on DNA separation: Experimental results and numerical simulations

The various potential factors affecting the performance of nanopillar chips on DNA separation were investigated from the viewpoints of both numerical calculations and actual experiments. To yield higher performance and replace the conventional DNA separation techniques such as microchip electrophoresis, the phenomenon specific to the nanopillar chips should be deeply understood. In this paper, although various factors affecting the performance of the nanopillar chips are considered, we focused on the effect of electroosmotic flow, which is particularly noticeable in quartz-made nanopillar chips. High-resolution separation of DNA was realized when an electroosmotic flow was suppressed by simply using a higher concentration of buffer, but DNA separation failed in the presence of an electroosmotic flow. It was confirmed from the numerical simulations and the direct observations that the deformation of DNA band during the injection process was induced by electroosmotic flow and consequently led to a poor resolution.     

Analysis of nonlinear transient responses of piezoelectric resonators

The electric transient response method is an effective technique to evaluate material constants of piezoelectric ceramics under high-power driving. In this study, we tried to incorporate nonlinear piezoelectric behaviors in the analysis of transient responses. As a base for handling the nonlinear piezoelectric responses, we proposed an assumption that the electric displacement is proportional to the strain without phase lag, which could be described by a real and constant piezoelectric e-coefficient. Piezoelectric constitutive equations including nonlinear responses were proposed to calculate transient responses of a piezoelectric resonator. The envelopes and waveforms of current and vibration velocity in transient responses observed in some piezoelectric ceramics could be fitted with the calculation including nonlinear responses. The procedure for calculation of mechanical quality factor Q(m) for piezoelectric resonators with nonlinear behaviors was also proposed.     

Nano-strip grating lines self-organized by a high speed scanning CW laser

After a laser annealing experiment on Si wafer, we found an asymmetric sheet resistance on the surface of the wafer. Periodic nano-strip grating lines (nano-SGLs) were self-organized along the trace of one-time scanning of the continuous wave (CW) laser. Depending on laser power, the nano-trench formed with a period ranging from 500 to 800 nm with a flat trough between trench structures. This simple method of combining the scanning laser with high scanning speed of 300 m min(-1) promises a large area of nanostructure fabrication with a high output. As a demonstration of the versatile method, concentric circles were drawn on silicon substrate rotated by a personal computer (PC) cooling fan. Even with such a simple system, the nano-SGL showed iridescence from the concentric circles.     

A Simple Pneumatic Loading System Controlling Stress and Strain Rates for One-Dimensional Compression of Clay

A simple but automated pneumatic loading system that can control the stress and strain rates for one-dimensional (1D) compression of clay was developed. The rate-dependency of stress-strain behaviour due to the viscous property of clay was investigated by 1D compression tests on standard-size specimens by various loading methods: 1) Standard Consolidation Tests (SCTs), stepwise increasing the axial stress two times every one day; 2) ordinary Constant-Rate-of-Strain (CRS) tests at different strain rates; 3) special CRS tests including unloading and reloading cycles with different stress amplitudes at strain rates of which the absolute value was either kept constant throughout respective tests or changed at the start of reloading; and 4) special CRS tests including a number of sustained loading (SL) during otherwise primary loading or unloading or reloading at constant strain rate. Sufficiently low strain rates were employed to ensure essentially fully drained condition. The followings were found. Despite that the newly developed pneumatic loading system is rather simple, 1D compression tests following such various loading histories as above can be performed on four types of clay rather accurately. The stress-strain behaviour of clay is significantly rate-dependent, exhibiting significant creep strains at SL stages. The creep strain rate is significantly different whether SL starts during otherwise primary loading or unloading or reloading, controlled by the magnitude and sign of the initial strain rate at the start of SL. The whole observed trends of rate-dependent stress-strain behaviour can be qualitatively explained by the non-linear three-component elasto-viscoplastic model extended to cyclic loading conditions.     

Anti-obesity and anti-diabetic effects of ethanol extract of Artemisia princeps in C57BL/6 mice fed a high-fat diet

Artemisia princeps is commonly used as a food ingredient and in traditional Asian medicine. In this study, we examined the effects of long-term administration of an ethanol extract of A. princeps (APE) on body weight, white adipose tissue, blood glucose, insulin, plasma and hepatic lipids, and adipocytokines in C57BL/6 mice fed a high-fat diet. Daily feeding of a 1% APE diet for 14 weeks normalized elevated body weight, white adipose tissue, and plasma glucose and insulin levels, and delayed impaired glucose tolerance in mice a fed high-fat diet. These events were not observed in mice fed a control diet containing 1% APE. Liver triglyceride and cholesterol levels were similar in mice fed a 1% APE-diet and those fed a control diet. In the high-fat diet groups, APE inhibited hepatic fatty acid synthase (FAS) and suppressed the elevation of plasma leptin, but had no effect on adiponectin levels. These findings suggest that the regulation of leptin secretion by APE may inhibit FAS activity with subsequent suppression of triglyceride accumulation in the liver and adipose tissues. Inhibition of lipid accumulation can, in turn, lead to improvements in impaired glucose tolerance.     

Effect of cross-flow on the frequency of bubble formation from a single-hole nozzle

Bubble formation from a single-hole nozzle placed vertically upward in a rotating water bath was investigated using a high-speed video camera. Air was used as the working gas. The measured values of the frequency of bubble formation, f _B, were compared with those observed in a stationary bath, f _B0. The velocity of cross-flow, ν_θ, affected the bubble formation significantly when it exceeded a critical value, ν_θc . The ratio of f _B to f _B0 was unity for ν_θ≦ν_θc , but it changed in a complex manner for ν_θ>ν_θc . In the latter case, when the air flow rate Q _g was relatively low, f _B/f _B0 became larger than unity irrespective of Q _g, and an empirical correlation of f _B/f _B0 was proposed as a function of ν_θ and the inner diameter of the nozzle, d _ni. As the gas flow rate increased, f _B/f _B0 decreased monotonically and became smaller than unity, and an empirical correlation of f _B/f _B0 was derived as a function of Q _g, ν_θ, and d _ni. These empirical correlations could approximate the measured values of f _B/f _B0 within a scatter of −15 to +20 pct.     

Evaluation of Tensile Strength and Fracture Toughness of Yttria-Stabilized Zirconia Polycrystals with Fracture Surface Analysis

The tensile strength of yttria-stabilized tetragonal zirconia polycrystals (Y-TZPs) was measured and the fracture surfaces were analyzed with the scanning electron microscope and X-ray microanalyzer. The fracture origins of the pressureless-sintered samples were voids or inclusions such as A1₂O₃, A1₂O₃ with SiO₂, and cubic-ZrO₂, while the fracture origins of the hot isostatically pressed samples were inclusions; no voids were detected at fracture origins. The higher strengths of the hot isostatically pressed samples versus those of the pressureless-sintered samples were consistent with the change in fracture origins. The fracture toughness of the samples calculated from the tensile strength and analysis of the fracture origins was 3.4 to 3.7 MPa √m. These values are lower than those measured with the SEPB method. These discrepancies might be caused by the difference in the state of the fracture origin and its neighborhood, such as the size of the fracture origin and interaction between two surfaces in the precrack.