Enzymatic esterification of glycerol II. Lipase-catalyzed synthesis of regioisomerically pure 1(3)-rac-monoacylglycerols

Regioisomerically pure 1(3)-rac-monoacylglycerols are conveniently prepared in high yields (>75%) and in multigram quantities by enzymatic esterification of glycerol in the presence of various lipases(Chromobacterium viscosum, Rhizopus delemar, Rhizomucor miehei) with a variety of different acyl donors, such as free fatty acids, fatty acid alkyl esters, vinyl esters and triacylglycerols, as well as natural fats and oils. All reactions are carried out in aprotic organic solvents with low water content, namelyn-hexane, diethyl ether, tBuOMe or mixtures of these solvents. Essential for the success of these transformations were the following two factors. First, the creation of an artificial interphase between the solvent-immiscible hydrophilic glycerol and the hydrophobic reaction medium by its adsorption onto a solid support. Second, a facile system for the separation of the desired monoacylglycerol from the reaction mixture, coupled with the continuous recycling of acyl donor and undesirable by-products.     

Statistical Analysis of the Intergranular Film Thickness in Silicon Nitride Ceramics

Silicon nitride materials typically reveal thin amorphous intergranular films along grain boundaries, with only the exception of special boundaries. It is known that such grainboundary films strongly affect the high-temperature properties of the bulk material. High-resolution electron microscopy (HREM) was used to study these amorphous films in different Si₃N₄ ceramics. The observed film thicknesses at grain boundaries in these materials varied between 5and 15 Å. It was shown that the grain-boundary film thickness strongly depends on film chemistry. Careful inspections of film-thickness measurements across grain boundaries in a given material suggest that the film widths vary on the order of 1 Å. Therefore, a quantitative evaluation should allow for the determination of the standard deviation of the film thickness. The amorphous film widths along grain boundaries in four materials were measured over the entire length (up to 1 μm) of the grain boundary between two triple points. Forty to fifty data points were evaluated for each boundary, giving a Gaussian-like distribution of the film thickness around a median value, which corresponded well with the film width measured from single HREM micrographs. The accuracy achieved by the statistical method was better than ± 1 Å.     

Fluidized bed combustion of high ash anthracite: Analysis of combustion efficiency and particle size distribution

Fluidized bed combustion of high ash anthracite (HAA) was experimentally studied. The combustor consists of 0.25 m ID bed, and auxiliary equipments for coal feeding, ash removal, lemperature control, etc. Experimental results elucidate main cause of fuel loss to be elutriation of fines (i.e., flyash) containing unburned carbon. However, detailed balances of particle size distribution show majority of carbon in flyash comes from fines contained in the feed instead of attrition of coarse particles. The latter is the main source of flyash for conventional coal. The difference is due to much smaller attrition rate of HAA; feed HAA particles do not shrink much in size by combustion and attrition.     

Korrosion von ölgefeuerten Zentralheizungskesseln

Corrosion of oil-fired domestic boilers Depending on the surface temperature of the flue gas side the corrosion of oil fired domestic boilers proceeds either mainly by acid corrosion or by oxygen corrosion:

• – At surface temperatures of 60°C and higher the corrosion mechanism of acid corrosion prevails and the corrosion rates amount to 0.1–0.3 mm/year (values referred to continuous burner operation). The corrosion products consist of soluble iron(II)- and iron(III)sulfates. Higher corrosion rates can be attributed to an appreciable catalytic formation of sulfur trioxide on the corrosion products formed on the convective heating surfaces.
• – At surface temperatures of 40°C the mechanism of oxygen corrosion already dominates and the corrosion rates are about ten times higher (1.5–3 mm/year, referred to continous burner operation). The high portion of ioron oxide hydrates, especially goethit (α-FeOOH), makes the corrosion products difficult to remove.
• – Distinctly reduced service lives are also expected for the so called reduced temperature boilers (“Niedertemperaturkessel”) and low temperature boiers (“Tieftemperaturkessel”): According to the manufacturers these boilers may be operated at boiler water temperatures well below 60°C, as they are equipped with constructive measures to enhance the surface temperature on the flue gas side. However, these measures are only fully effective under stationary conditions.

Some of the results were obtained from weight loss measurements on test specimen made from St 35.8 and gray cast iron, that were exposed to the flue gases of an oil fired experimental boiler. Other important results come from field measurements of the sulfuric acid content of about 30 boilers that are in practical use.     

Nitrogen removal using recycled polystyrene bottles as biofilm media

The performance of an attached growth wastewater treatment process was investigated in an effort to improve nitrogen removal efficiency. Recycled Yakult (lactic acid fermentation drink) bottles made of polystyrene were used as a biofilm media. The use of Yakult bottles as a biofilm media has been attempted by numerous researchers in Japan for the removal of solids and organics. However, these studies focused only on the removal of solids and organics. This study extended their application to the removal of nitrogen for domestic sewage treatment. Yakult media was placed in a reactor with 70% apparent reactor volume in a conventional A/O process. The bottom of the Yakult media was removed, and randomly filled Yakult media were effectively able to reduce the flow in tanks, resulting in an increase in the contact time between pollutants and microorganisms. With higher HRT, the nitrogen removal efficiency was increased by up to 83% with 12 hr of HRT. Nitrification appeared to be the limiting factor of nitrogen removal at an HRT that is less than 12 hr, indicating that the Yakult process requires more retention time to achieve nitrification compared to other biofilm processes. The removal efficiencies of organics and solids were high regardless of the change of operational parameters. This article is based on a presentation in “The 7th Korea-China Workshop On Advanced Materials” organized by the Korea-China Advanced Materials Cooperation Center and the China-Korea Advanced Materials Cooperation Center, held at Ramada Plaza Jeju Hotel, Jeju Island, Korea on August 24–27, 2003.     

Thermodynamic reassessment of the Cd−Zn system

The Cd−Zn system has been thermodynamically reassessed with the CALPHAD method by combining more recent experimental data, in particular the activities of zinc in the liquid phase. A good agreement is obtained between the calculated and experimental thermodynamic parameters as well asphase boundaries.     

1984 A camptown story

This essay examines Kim Yongt’ae’s photocollage DMZ, which consists of photo-portraits he acquired from commercial photo studios in US military camptowns in South Korea. The co-founding member of the South Korean artist group Hy?nsilgwa par?n (Reality and Utterance), Kim visited camptowns in 1984. There, he found hundreds of studio photo-portraits depicting Korean women and American GIs serving United States Forces Korea (USFK). While discussions on “found” photographs often center on the discourses of archive, appropriation, or vernacularity appended by the cultural specificity of their origins, this essay proposes a new framework through which Kim’s work is explored: transnational militarism and “disidentification” — a concept put forth by José Esteban Muñoz on minoritarian performativity. Through this framework, DMZ challenges the binary reading of camptown subjects as victim and victimizer and proposes the performative formation of a new subjectivity.     

Electromigration effect on Sn-58 % Bi solder joints with various substrate metallizations under current stress

The electromigration behavior of low-melting temperature Sn-58Bi (in wt%) solder joints was investigated with a high current density between 3 and 4.5 × 10³ A/cm² between 80 and 110 °C. In order to analyze the impact of various substrate metallizations on the electromigration performance of the Sn-58Bi joint, we used representative substrate metallizations including electroless nickel immersion gold (ENIG), electroless nickel electroless palladium immersion gold (ENEPIG), and organic solderability preservatives (OSP). As the applied current density increased, the time to failure (TTF) for electromigration decreased regardless of the temperature or substrate metallizations. In addition, the TTF slightly decreased with increasing temperature. The substrate metallization significantly affected the TTF for the electromigration behavior of the Sn-58Bi solder joints. The substrate metallizations for electromigration performance of the Sn-58Bi solder are ranked in the following order: OSP-Cu, ENEPIG, and ENIG. Due to the polarity effect, current stressing enhanced the fast growth of intermetallic compounds (IMCs) at the anode interface. Cracks occurred at the Ni₃Sn₄ + Ni₃P IMC/Cu interfaces on the cathode sides in the Sn-58Bi/ENIG joint and the Sn-58Bi/ENEPIG joint; this was caused by the complete consumption of the Ni(P) layer. Alternatively, failure occurred via deformation of the bulk solder in the Sn-58Bi/OSP-Cu joint. The experimental results confirmed that the electromigration reliability of the Sn-58Bi/OSP-Cu joint was superior to those of the Sn-58Bi/ENIG or Sn-58Bi/ENEPIG joints.