角调谐飞秒同步泵浦KTP红外光参量振荡器

用平均输出功率为１．１Ｗ，脉宽为９０ｆｓ的商用再生锁模Ｔｉ：Ｓａｐｐｈｉｒｅ激光器作为泵浦源，用ＫＴＰ作为非线性光学介质，制成一台同步泵浦飞秒光学参量振荡器。其输出调谐范围为１．０４μｍ至１．２６μｍ，平均输出功率在１００ｍｗ左右，脉宽仅约１００ｆｓ。     

石油焦原料性质及炭化工艺对活性炭性能的影响

从分析石油焦原料着手，考察了其热解特性、孔隙率和石墨化程度。由于石油焦结构致密，属易石墨化碳，因此用水蒸气法直接活化得到的炭质材料吸附性能差，其碘吸附值小于350mg/g。不同来源的石油焦由于组成不同，其活化性能也有差异。通过成型法，以金山石油焦为原料轻预炭化、预氧化和炭化，得到炭化料，再用水蒸气活化得到的活性炭的碘吸附值达800.40mg/g、亚甲蓝值达120.40mg/g。以独山子石油焦为主要原料制得的活性炭的碘吸附值与亚甲蓝值分别达871．58mg/g、100..67mg/g。     

大江河口三维非线性斜压水流盐度数学模型

本文建立了河口三维非线性斜压水流盐度数学模型。该模型通过。坐标变换，使整个水域垂直方向可采用相同的分层。基于过程分裂法，将三维流动分成表面重力波（外模式）和内重力波（肉模式）。外模式采用改进型双步全隐有限差分DSI法进行计算，内模式利用欧拉-拉格朗日公式，改进三维垂直方向隐式格式，减小了数值耗数，提高了计算精度及稳定性。该模型应用于长江口三维盐水入侵计算，结果表明水流盐度分布与实测一致。     

Ti,N,Mg对M2高速钢凝固组织和硬度的影响

为了改善Ｍ２高速钢共晶碳化物的分布，本文利用小凝固试样变质的方法研究了Ｔｉ，Ｎ和Ｍｇ对Ｍ２高速钢凝固组织和硬度的影响。试验结果表明，加入Ｔｉ或Ｔｉ－Ｎ后，共晶碳化物形态和分布有很大改善，而加入Ｔｉ－Ｎ后对凝固组织有轻微的细化作用，但只添加Ｔｉ不补碳时，钢的淬火硬度和回火硬度均下降；加入适量的Ｍｇ可以使片状的Ｍ２Ｃ型共晶碳化物转为鱼骨状的Ｍ６Ｃ型共晶碳化物，使其分布有所改善，Ｔｉ和Ｍｇ复合加入可以明     

斯伦贝谢Scanner家族新成员—R_t Scanner简介

本文详细介绍了斯伦贝谢公司最近推出来的测井仪器—Scanner家族的三分量感应测井仪R_t Scanner。该仪器可以同时测量纵向和横向电阻率以及地层倾角和方位角的信息。同时还能够得到标准的阵列感应成像测井剖面。在薄层和低阻油层解释以及储层各向异性分析中显示了独到的优势,文中给出了一个油田应用实例,最后介绍了R_t Scanner的仪器规格。     

A novel ultracompact two-mode-interference wavelength division multiplexer for 1.5-/spl mu/m operation

A novel ultracompact 2/spl times/2 wavelength division multiplexer (WDM) for 1.55-/spl mu/m operation based on highly dispersive two-mode interference (TMI) was designed, theoretically modeled, and verified using a finite-difference-time-domain (FDTD) method. A two-moded waveguide assisted with a dispersive tooth-shaped grating provided a mode-dependent reflection band of central wavelength at 1.55 /spl mu/m. The wavelengths of 1538 and 1572 nm that were at the band edges and had the lowest reflection losses and relatively high dispersion were selected for wavelength multiplexing. The result showed that the wavelengths were separated by grating dispersion in a coupler length of 75 /spl mu/m which was much shorter than the required length of 1.1 mm in a regular TMI multiplexer of no grating. Insertion loss of about 1.7 dB and channel contrast of about 12 dB were achieved.     

助催化剂对TiCl_4/MgCl_2催化丙烯高温聚合的影响

研究了助催化剂种类(三甲基铝、三异丁基铝、三正己基铝、三乙基铝和甲基铝氧烷)及其含量对无内、外给电子体的TiCl4/MgCl2催化剂催化丙烯高温(100℃)聚合性能的影响,并用结晶分级分析、示差扫描量热和凝胶渗透色谱等方法分析了所得聚丙烯的结晶熔融行为和微观结构。实验结果表明,聚合温度从70℃升至100℃时,TiCl4/MgCl2催化剂的定向能力基本不变;100℃聚合时,以烷基化能力较弱的三异丁基铝为助催化剂时TiCl4/MgCl2催化剂的活性最高,而采用烷基化能力最强的三甲基铝为助催化剂时TiCl4/MgCl2催化剂的活性最低;100℃聚合时,助催化剂的种类对TiCl4/MgCl2催化剂的定向能力影响很小。     

Effect of Cu concentration on the reactions between Sn-Ag-Cu solders and Ni

The reaction between the Sn-Ag-Cu solders and Ni at 250°C for 10 min and 25 h was studied. Nine different Sn-Ag-Cu solders, with the Ag concentration fixed at 3.9 wt.% and Cu concentrations varied between 0.0–3.0 wt.%, were used. When the reaction time was 10 min, the reactions strongly depended on the Cu concentration. At low-Cu concentrations (≦0.2 wt.%), only a continuous (Ni_1−xCu_x)₃Sn₄ layer formed at the interface. When the Cu concentration increased to 0.4 wt.%, a continuous (Ni_1−xCu_x)₃Sn₄ layer and a small amount of discontinuous (Cu_1−yNi_y)₆Sn₅ particles formed at the interface. When the Cu concentration increased to 0.5 wt.%, the amount of (Cu_1−yNi_y)₆Sn₅ increased and (Cu_1−yNi₆)₆Sn₅ became a continuous layer. Beneath this (Cu_1−yNi_y)₆Sn₅ layer was a very thin but continuous layer of (Ni_1−xCu_x)₃Sn₄. At higher Cu concentrations (0.6–3.0 wt.%), (Ni_1−xCu_x)₃Sn₄ disappeared, and only (Cu_1−yNi_y)₆Sn₅ was present. The reactions at 25 h also depended strongly on the Cu concentration, proving that the strong concentration dependence was not a transient phenomenon limited to a short reaction time. The findings of this study were rationalized using the Cu-Ni-Sn isotherm. This study shows that precise control over the Cu concentration in solders is needed to produce consistent results.     

Time and Temperature Factors in Construction of Rock Strength Criteria

Using the synthesis of the kinetic concept on solid strength and the Coulomb - Mohr strength theory as the base, the failure conditions taking into account the time and temperature factors are obtained.