A combined dislocation—cohesive zone model for fracture in a confined ductile layer

The collective dislocation behavior near a crack tip in a ductile layer sandwiched between two brittle solids is analyzed via two-dimensional dislocation dynamics (DD) simulations that incorporate a cohesive zone (CZ) model. The cohesive crack tip is treated as part of a much larger finite crack confined in the ductile layer. The underlying boundary value problem is formulated with a set of boundary integral equations and numerically evaluated with a collocation method. The fracture energy of the layered composite material is shown to be strongly correlated with the layer thickness and is directly influenced by the cohesive strength of the ductile layer (Hsia KJ et al. (1994) J Mech Phys Solids 6 877–896).     

Effects of Ti on N distribution and diffusion in FeTiN thin films

We studied the distribution and diffusion of N atoms in FeTiN single-layer and bilayer thin films by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). We found that in as-deposited films N atoms are first absorbed by Ti atoms, the rest being dissolved into FeTi lattices. Ti not only directly absorbs N by chemical bonding, but also decreases the energy of the N atoms that are dissolved into FeTi lattices. The diffusion study of N atoms in single layer and bilayer films showed that although the presence of Ti stabilized the /spl alpha/ phase of FeTi lattices during 200/spl deg/C annealing, the diffusion length of dissolved N in FeTi (Ti/spl les/8 at.%) lattices was still comparable to the diffusion length of N in pure Fe. Thus, the addition of a small amount of Ti in /spl alpha/-Fe lattice can not completely stabilize N atoms in the film, and the induced magnetic anisotropy of the films can still be unstable, although the /spl alpha/ phase of FeTiN is stabilized by the addition of Ti. The distribution of N atoms in bilayer films can be fitted by a simple enthalpy model.     

Euler Critical Force Calculation for Laced Columns

The paper presents a method of solving the buckling problem of laced column as a statically indeterminate structure without analyzing determinants of high order. The flexural and torsional buckling problems of laced column are reduced to the two-point boundary value problem for a difference equation system. The value of Euler critical load is determined as a result of analyzing the fourth order determinant for column with any degree of static indeterminacy. The solution is based on the method of initial values. Stability of columns with any types of lattice (crosswise, serpentine, with batten struts); with any number of lattice panels and with variable lattice spacing can be examined by this manner. The analogy between the flexural and torsional buckling of the laced column is established. It enables one to use the same relations for consideration of both kinds of buckling. The obtained numerical results show that the Euler critical loads calculated by this method can be substantially differed from those based on the approximated Engesser’s approach. A PC program for checking stability of laced column by designer can be developed on the basis of the present method.     

Sex, Age, and Training Modulate Spatial Memory in the Rhesus Monkey (Macaca mulatta).

The authors tested 90 rhesus monkeys (Macaca mulatta) on a task of spatial memory, the spatial Delayed Recognition Span Test. The results showed that performance declined significantly with age, males had greater scores than females, and the rate of apparent decline with age was greater in males than in females. Both working and reference memory declined with age, but only working memory showed sex differences. The authors compared these data with that of 22 monkeys who were trained on a simpler version of the task before formal testing. Training had no effect on males but dramatically improved working memory in young females. The results confirm a male advantage in spatial working memory at a young age and confirm a greater decline with age in males than in females. It is important to note that prior training completely reverses the deficits of young females. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Analysis of the critical heat flux in round vertical tubes under low pressure and flow oscillation conditions. Applications of artificial neural network

Artificial neural networks (ANNs) for predicting critical heat flux (CHF) under low pressure and oscillation conditions have been trained successfully for either natural circulation or forced circulation (FC) in the present study. The input parameters of the ANN are pressure, mean mass flow rate, relative amplitude, inlet subcooling, oscillation period and the ratio of the heated length to the diameter of the tube, L/D. The output is a nondimensionalized factor F, which expresses the relative CHF under oscillation conditions. Based on the trained ANN, the influences of principal parameters on F for FC were analyzed. The parametric trends of the CHF under oscillation obtained by the trained ANN are as follows: the effects of pressure below 500 kPa are complex due to the influence of other parameters. F will increase with increasing mean mass flow rate under any conditions, and will decrease generally with an increase in relative amplitude. F will decrease initially and then increase with increasing inlet subcooling. The influence curves of mean mass flow rate on F will be almost the same when the period is shorter than 5.0 s or longer than 15 s. The influence of L/D will be negligible if L/D>200. It is found that the minimum number of neurons in the hidden layer is a product of the number of neurons in the input layer and in the output layer.     

Software release management for component‐based software

Software release management is the process through which software is made available to and obtained by its users. Until now, this process has been relatively straightforward. However, the emergence of component‐based software is complicating software release management. Increasingly, software is constructed via the assembly of pre‐existing, independently produced, and independently released components. Both developers and users of such software are affected by these complications. Developers need to accurately document the complex and changing dependencies among the components constituting the software. Users must be involved in locating, retrieving, and assembling components in order to appropriately bring the software into their particular environment. In this paper, we introduce the problem of release management for component‐based software and discuss SRM, a prototype software release management tool we have developed that supports both developers and users in the software release management process. Copyright © 2002 John Wiley & Sons, Ltd.     

Measurement methods for LCoS displays

Abstract— Two measurement methods to characterize uniformity and the absolute cell gap of LCoS images will be reviewed. These are simple to use in a production environment and have allowed major improvements in manufacture to be achieved. For the purpose of this paper, the liquid‐crystal mode used is the 45° normally black mode.     

Context Switching in a Run-Time Reconfigurable System

A distinguishing feature of reconfigurable computing over rapid prototyping is its ability to configure the computational fabric on-line while an application is running. Conventional reconfigurable computing platforms utilize commodity FPGAs, which typically have relatively long configuration times. Shrinking the configuration time down to the nanosecond region opens possibilities for rapid context switching and virtualizing the computational resources. An experimental context-switching FPGA, called the CSRC, has been created by BAE Systems, and gives researchers the opportunity to explore context-switching applications. This paper presents results obtained from constructing both control-driven and data-driven context switching applications on the CSRC device, along with unique properties of the run-time and compile-time environment.     

Retrieval Of Morphological Variants In Searches Of Latin Text Databases

This paper reports a detailed evaluation of the effectiveness of a system that has been developed for the identification and retrieval of morphological variants in searches of Latin text databases. A user of the retrieval system enters the principal parts of the search term (two parts for a noun or adjective, three parts for a deponent verb, and four parts for other verbs), this enabling the identification of the type of word that is to be processed and of the rules that are to be followed in determining the morphological variants that should be retrieved. Two different search algorithms are described. The algorithms are applied to the Latin portion of the Hartlib Papers Collection and to a range of classical, vulgar and medieval Latin texts drawn from the Patrologia Latina and from the PHI Disk 5.3 datasets. The effectiveness of these searches demonstrates the effectiveness of our procedures in providing access to the full range of classical and post-classical Latin text databases. This revised version was published online in July 2006 with corrections to the Cover Date.     

Detecting infeasibility and generating cuts for mixed integer programming using constraint programming

We study a hybrid MIP/CP solution approach in which CP is used for detecting infeasibilities and generating cuts within a branch-and-cut algorithm for MIP. Our framework applies to MIP problems augmented by monotone constraints that can be handled by CP. We illustrate our approach on a generic multiple machine scheduling problem, and present a number of computational experiments.