Static-state feedback control of discrete-event systems underpartial observation

Studies static-state feedback control of discrete-event systems under partial observation. The authors present a necessary and sufficient condition for the existence of a static-state feedback controller. A static controller is a special case of a dynamic controller studied by Kumar et al. The authors' condition, however, has computational advantage in contrast to those obtained by Kumar et al. The authors also present a necessary and sufficient condition under which the modular feedback synthesis is possible     

Closed-loop expressions of minimum energy control for single-inputlinear digital systems

Closed-loop expressions for the minimum energy control of a single-input linear digital system are described. They are obtained by two different methods. The optimal inputs are given by state feedback with the bounded variable gains. The gains are independent of the initial state of the system     

TQM implementation in hospitals

This paper discusses the essential elements for successful Total Quality Management (TQM) implementation in hospital, and the challenges that occur with such implementation. Guidelines for this implementation are provided to show how TQM tools can be used effectively in hospitals.     

Behavior of a vibrating wire near the liquid3He-vacuum interface and in a saturated3He-4He mixture

In this paper we describe the effect of the vicinity of a liquid³He-vacuum interface on the behavior of a vibrating wire viscometer. It was found that in the fluid near the liquid interface the quality factor is lower than in the bulk liquid. We further report on the observation of a doubling of the resonance peak of the wire in a saturated³He-⁴He mixture. The frequencies and amplitudes of the two peaks strongly depend on the distance between the phase boundary and the vibrating wire; the temperature and the velocity of the phase boundary have no significant influence on the peak frequencies. The observed peak doubling is attributed to the coupling of the vibrating wire with a standing second-sound wave in the dilute phase where the volume of the dilute phase can be regarded as a resonating cavity for second sound.     

Microstructure and mechanical behaviour of 3Y-TZP/Mo nanocomposites possessing a novel interpenetrated intragranular microstructure

Yttria stabilized tetragonal zirconia polycrystal (Y-TZP)/0-100 vol % molybdenum (Mo) composites were fabricated by hot-pressing a mixture of Y-TZP powder containing 3 mol % yttria (Y₂O₃) and a fine Mo powder in vacuum. This composite system possessed a novel microstructural feature composed of an interpenetrated intragranular nanostructure, in which either nanometer sized Mo particles or equivalent sized zirconia (ZrO₂) particles located within the ZrO₂ grains or Mo grains, respectively. The strength and toughness were both greatly enhanced with increasing Mo content for the 3Y-TZP/Mo composites thus breaking through the strength-toughness tradeoff relation in transformation toughened ZrO₂ and its composite materials. They exhibited a maximum strength of 2100 MPa and a toughness of 11.4 MPa·m^1/2 for the composite containing 70 vol % Mo. These simultaneous improvements in strength and toughness were determined to be the result of a decrease in flaw size associated with the interpenetrated intragranular nanostructure, and a stress shielding effect created in the crack tip by the elongated Mo polycrystals bridging the crack tip in addition to the stress induced phase transformation.     

Variation of the creep limit and structure of a welded joint in PT-3V titanium alloy under the effect of cyclic loading. Report 2

Comparative analysis of the characteristics of amplitude-dependent internal friction (IF) was carried out to explain reasons leading to an increase of the creep limit of the butt welded joint in PT-3V titanium alloy (PT-2V filler material) after cyclic loading. IF was measured by the method of the direct torsional pendulum on cylindrical specimens representing the gage part of the specimens subjected to preliminary cyclic loading. The data were processed using the Granato-Lucke theory. The results show that the reduction of IF after cyclic loading took place as a result of an increase of the number and redistribution of pinning points of the dislocations. Consequently, the density of mobile dislocations decreases by 8% and the length of dislocation segments by 18%. These processes of stabilization of the structure were completed within 5·10 ⁴ cycles of preliminary loading. Stabilization of the dislocation structure of the material of the welded joint increases its creep limit.Translated from Problemy Prochnosti, No. 4, pp. 35–40, April, 1996.