Shear mode coupling and tilted grain growth of A1N thin films in BAW resonators.

Polycrystalline A1N thin films were deposited by RF reactive magnetron sputtering on Pt(111)/Ti electrode films. The substrates were tilted by an angle ranging from 40 degrees to 70 degrees with respect to the target normal. A low deposition temperature and a high sputter gas pressure were found ideal for tilted growth. The resulting grain tilt angle amounts to about half the substrate tilt angle. For coupling evaluation, 5 GHz solidly mounted resonator structures have been realized. The tilted grain A1N films exhibited a permittivity in the 9.5-10.5 range and loss tangent of 0.3%. Two shear modes as well as the longitudinal mode could be clearly identified. The coupling coefficient k2(eff) of the fundamental thickness shear mode (TS0) was found to be about 0.5%, which is compatible with a c-axis tilt of about 6 degrees.     

Modelling diffusion-controlled kinetics in equilibrium and driven alloys

Summary We introduce a very simple model for thermally activated atomic migration on a lattice, and several techniques to handle it. For thermodynamical systems, the model can be used for simulating decomposition paths taking into account relevant metallurgical features. Close to equilibrium, the simplest mean-field approximation of the model can be linearized with respect to the departure from equilibrium; one then gets a microscopic interpretation of classical phenomenological coefficients, such as mobility, interfacial transfer coefficient, rate constants for the coupled relaxation of concentration and order fields. Further away from the equilibrium, the nonlinearities can be taken into account in a consistent way. For driven alloys, i.e. alloys submitted to external forcing, forced atomic migration is added to the model and new features emerge: the model is supported by several experimental results some of which confirmed its predictions a posteriori.     

Transient characteristics of small salient-pole alternators

The use of small alternators, other than for standby purposes, is increasing and this has focused attention on the reliability and utility of the parameters normally quoted for such machines. Test procedures are described and methods used for parameter estimation discussed, with particular emphasis on the difficulties presented by small brushless machines     

Effect of stepper lens operating conditions on proximity effects in DUV optical lithography down to 250nm

Reduction of optical proximity effects (OPE), at deep uv wavelength of 248nm, caused by the variation of stepper lens operating conditions is investigated. It is shown that many of these effects, which increase as the Rayleigh limit is approached, can be minimised, and in many cases eliminated, by suitable choice of lens numerical aperture (NA) and partial coherence (sigma, σ).

Application of these results should enable the user of advanced wafer steppers to carry out high resolution lithography with a minimum of time consuming optical proximity correction (OPC).     

APPLICATION OF SITE-SPECIFIC NATURAL ISOTOPE FRACTIONATION (SNIF-NMR) OF HYDROGEN TO THE CHARACTERIZATION OF EUROPEAN BEERS

More than one hundred samples of European beers have been investigated by the new SNIF-NMR method which is based on 2H NMR at the natural abundance level and enables site-specific natural isotope fractionation factors in ethanol to be determined. The relative (R) and absolute (D/H)_i, parameters are shown to be characteristic of the country where the beers are brewed and the observed variations are explained in terms of cereal composition, water resource, and manufacturing processing (fermentation, yeast, temperature cycle). These new parameters find analytical and mechanistic applications in the identification of a beer and in the investigation of a fermentation process.     

The Future of Mixing Research

This paper is the result of a plenary discussion session held at the 11^th European Conference on Mixing. Three perspectives on mixing research are explored: that of the industrialist, the equipment manufacturer, and the academic researcher. There was strong agreement that, while the one dimensional problems are reasonably well understood and many engineers thus perceive that mixing is simple, current practice actually requires us to address complex, multi‐dimensional problems with interactions between mixing, reaction, multi‐phase physics, surface phenomena, and transport phenomena. Understanding these multi‐scale, multi‐mechanism problems requires models which include interactions between the phenomena, and allow the effects of these interactions to emerge. Developing these models will require us to shift our perspective on mixing from one of equipment design to one of the mixing field as a fundamental physical mechanism.     

Calculation of secondary cable losses and ampacity in the presenceof harmonics

A simplified procedure for computing ohmic losses in secondary distribution cable systems by extending the Neher-McGrath model for 60 Hz losses is presented. Specifically, simplified formulae for evaluating ohmic losses due to harmonics are given. These results are subsequently used to compute the cable ampacity or the derating factor due to harmonics. The overall method is simple to follow and can be performed with a calculator. A typical example is given