Luminescence from praseodymium doped AlN thin films deposited by RF magnetron sputtering and the effect of material structure and thermal annealing on the luminescence

Thin films of Praseodymium doped AlN are deposited on silicon (111) substrates at 77 K and 950 K by rf magnetron sputtering method. About 500–1000 nm thick films are grown at 100–200 watts RF power and 5–8 mTorr nitrogen, using a metal target of Al with Pr. X-rays diffraction results show that films deposited at 77 K are amorphous and those deposited at 950 K are crystalline. Cathodoluminescence studies are performed at room temperature and luminescence peaks are observed in a wide range from ultraviolet to infrared region. The most intense peak is obtained in green at 526 nm from amorphous films as a result from ³P₁→³H₅ transition. In crystalline films the intense peak was obtain in red at 648 nm as a result from ³P₀→³F₂ transition. Films are thermally activated at 1300 K for half an hour in a nitrogen atmosphere. Thermal activation enhances the intensity of luminescence. Two peaks at 488 nm and 505 nm merged after thermal activation, giving rise to a single peak at 495 nm.     

Life cycle cost analysis of alternative vehicles and fuels in Thailand

High crude oil prices and pollution problems have drawn attention to alternative vehicle technologies and fuels for the transportation sector. The question is: What are the benefits/costs of these technologies for society? To answer this question in a quantitative way, a web-based model (http://vehiclesandfuels.memebot.com) has been developed to calculate the societal life cycle costs, the consumer life cycle costs and the tax for different vehicle technologies. By comparing these costs it is possible to draw conclusions about the social benefit and the related tax structure. The model should help to guide decisions toward optimality, which refers to maximum social benefit. The model was applied to the case of Thailand. The life cycle cost of 13 different alternative vehicle technologies in Thailand have been calculated and the tax structure analyzed.     

Results of a User Study on 2D Hurricane Visualization

We present the results from a user study looking at the ability of observers to mentally integrate wind direction and magnitude over a vector field. The data set chosen for the study is an MM5 (PSU/NCAR Mesoscale Model) simulation of Hurricane Lili over the Gulf of Mexico as it approaches the southeastern United States. Nine observers participated in the study. This study investigates the effect of layering on the observer's ability to determine the magnitude and direction of a vector field. We found a tendency for observers to underestimate the magnitude of the vectors and a counter‐clockwise bias when determining the average direction of a vector field. We completed an additional study with two observers to try to uncover the source of the counter‐clockwise bias. These results have direct implications to atmospheric scientists, but may also be able to be applied to other fields that use 2D vector fields.     

Exchange and oxidation of CO on O-predosed Rh---Al2O3 and Rh---CeO2 catalysts

Exchange and oxidation of C¹⁶O were investigated at 450°C on ¹⁸O-predosed Rh and Pt catalysts supported on A1₂O₃, CeO₂ and CeO₂-Al₂O₃. In all cases, a rapid exchange of C¹⁶O with the surface can be observed. CO oxidation leads to C¹⁶O₂, C¹⁶O¹⁸O and C¹⁸O₂. Significant formation of C¹⁶O₂ is due to the relatively high ¹⁶O coverage in reaction resulting from the C¹⁶O exchange and from an exchange between O surface species and ¹⁶O internal atoms. Hydrogen is also formed via a water-gas shift reaction (CO + surface OH) in higher proportion on CeO₂-containing catalysts than on A1₂O₃. Chlorine inhibits all the reactions (exchange, oxidation and WGS) and particularly the internal exchange.     

Simplified 0.35-μm flash EEPROM process using high-temperatureoxide (HTO) deposited by LPCVD as interpoly dielectrics and peripheraltransistors gate oxide

A simplified flash EEPROM process was developed using high-temperature LPCVD oxide both as flash cells interpoly dielectrics and as peripheral transistors gate oxide (decoding logic). An O₂ anneal at 850°C lowers charge trapping and interface trap density induced by Fowler-Nordheim injection. However, electron trapping remains slightly higher than with dry thermal oxide. Similar memory charge loss and write-erase endurance are obtained as for ONO-insulated cells. HTO thus proves to have the required quality and reliability to be used in flash EEPROMs     

Potentiation of a three drug chemotherapy regimen by radiation

The combination of N-(phosphonacetyl)-L-aspartate, 6-methylmercaptopurine, and 6-aminonicotinamide has been shown to be an effective antineoplastic regimen and also to enhance the effects of other chemotherapeutic agents. The mechanism of action of this combination of drugs is not known definitively, but one possible mechanism is biochemical modulation of energy metabolism and inhibition of production of tumor ATP. Tumor-bearing mice were treated with N-(phosphonacetyl)-L-aspartate, followed 17 h later by 6-methylmercaptopurine and 6-aminonicotinamide. 31P nuclear magnetic resonance spectroscopic studies demonstrated a significant depletion of high energy phosphates at 10 h post-6-methylmercaptopurine and 6-aminonicotinamide. The addition of radiation at this time was shown to induce a significantly longer tumor growth delay and a greater number of regressions (including durable complete regressions) than either chemotherapy or radiation alone. The combination of chemotherapy and radiation was found to be supra-additive compared to the antineoplastic effects of either modality administered separately, without a measurable increase in host toxicity.     

Diffusion bonding of an aluminium-lithium alloy (AA8090) using aluminium-copper alloy interlayers

Diffusion bonds have been produced between sheets of an Al-Li-Cu-Mg-Zr alloy using aluminium-4% copper vapour deposited metallic interlayers. Microstructural changes occurred both in the parent alloy and in the bond interface after diffusion bonding cycles and post-bonding heat treatments were analysed. Different metallographic techniques (light microscopy, scanning and transmission electron microscopy) have been used. Diffusion bonding trials were carried out using the same alloy (AA8090), both in non-superplastic (T6) and superplastic conditions. Differences in their behaviours in relation to diffusion bonding were observed.