Surface leakage currents in SiN/sub x/ passivated AlGaN/GaN HFETs

A novel guarded surface leakage test structure is used to isolate the surface and bulk leakage contributions to gate current in AlGaN/GaN HFETs. Passivation with various recipes of SiN/sub x/ always resulted in the commonly observed increase in gate leakage, which was found to be dominated by bulk leakage through the AlGaN. However, high temperature deposited SiN/sub x/ recipes gave a 1-2 orders reduction in surface leakage, whereas low temperature deposition gave an increase. Gate lag measurements were found to correlate closely with the surface leakage component, giving direct evidence that the key device problem of current slump is associated with current flow at the AlGaN surface.     

Prebiotic synthesis of sequential peptides on the Hadean beach by a molecular engine working with nitrogen oxides as energy sources

Addressing the still open question of the prebiotic origin of sequential macromolecules (peptides, nucleic acids) on the primitive Earth, we describe a molecular engine (the primary pump), which works at ambient temperature and continuously generates, elongates and complexifies sequential peptides. This new scenario is based on a cyclic reaction sequence, whose keystep is the activation of amino acids into their N‐carboxyanhydrides (NCA) through nitrosation by NOx. This process could have taken place on tidal beaches; it requires a buffered ocean, emerged land and a nitrosating atmosphere. With the help of geochemical studies and computer simulations of atmosphere photochemistry, we show that the primitive Earth during the Hadean may have satisfied all these requirements. © 2001 Society of Chemical Industry.     

Income and expenditure in a spatial economy

The question explored in this paper is whether the center attracts more spending by all agents in a spatial economy than do peripheral locations, and why this might be so. This is the macroeconomics pendant to the microeconomic concern with accessibility.This paper is the result of discussions on the subject of time and space in economics with my good friend, Tonu Puu. I dedicate it to the memory of another dear friend, Claude Ponsard.     

Shear mode coupling and tilted grain growth of A1N thin films in BAW resonators.

Polycrystalline A1N thin films were deposited by RF reactive magnetron sputtering on Pt(111)/Ti electrode films. The substrates were tilted by an angle ranging from 40 degrees to 70 degrees with respect to the target normal. A low deposition temperature and a high sputter gas pressure were found ideal for tilted growth. The resulting grain tilt angle amounts to about half the substrate tilt angle. For coupling evaluation, 5 GHz solidly mounted resonator structures have been realized. The tilted grain A1N films exhibited a permittivity in the 9.5-10.5 range and loss tangent of 0.3%. Two shear modes as well as the longitudinal mode could be clearly identified. The coupling coefficient k2(eff) of the fundamental thickness shear mode (TS0) was found to be about 0.5%, which is compatible with a c-axis tilt of about 6 degrees.     

Modelling diffusion-controlled kinetics in equilibrium and driven alloys

Summary We introduce a very simple model for thermally activated atomic migration on a lattice, and several techniques to handle it. For thermodynamical systems, the model can be used for simulating decomposition paths taking into account relevant metallurgical features. Close to equilibrium, the simplest mean-field approximation of the model can be linearized with respect to the departure from equilibrium; one then gets a microscopic interpretation of classical phenomenological coefficients, such as mobility, interfacial transfer coefficient, rate constants for the coupled relaxation of concentration and order fields. Further away from the equilibrium, the nonlinearities can be taken into account in a consistent way. For driven alloys, i.e. alloys submitted to external forcing, forced atomic migration is added to the model and new features emerge: the model is supported by several experimental results some of which confirmed its predictions a posteriori.     

Transient characteristics of small salient-pole alternators

The use of small alternators, other than for standby purposes, is increasing and this has focused attention on the reliability and utility of the parameters normally quoted for such machines. Test procedures are described and methods used for parameter estimation discussed, with particular emphasis on the difficulties presented by small brushless machines     

Effect of stepper lens operating conditions on proximity effects in DUV optical lithography down to 250nm

Reduction of optical proximity effects (OPE), at deep uv wavelength of 248nm, caused by the variation of stepper lens operating conditions is investigated. It is shown that many of these effects, which increase as the Rayleigh limit is approached, can be minimised, and in many cases eliminated, by suitable choice of lens numerical aperture (NA) and partial coherence (sigma, σ).

Application of these results should enable the user of advanced wafer steppers to carry out high resolution lithography with a minimum of time consuming optical proximity correction (OPC).     

APPLICATION OF SITE-SPECIFIC NATURAL ISOTOPE FRACTIONATION (SNIF-NMR) OF HYDROGEN TO THE CHARACTERIZATION OF EUROPEAN BEERS

More than one hundred samples of European beers have been investigated by the new SNIF-NMR method which is based on 2H NMR at the natural abundance level and enables site-specific natural isotope fractionation factors in ethanol to be determined. The relative (R) and absolute (D/H)_i, parameters are shown to be characteristic of the country where the beers are brewed and the observed variations are explained in terms of cereal composition, water resource, and manufacturing processing (fermentation, yeast, temperature cycle). These new parameters find analytical and mechanistic applications in the identification of a beer and in the investigation of a fermentation process.     

A multiple-switch high-voltage DC-DC converter

Series connection of power devices has evolved into a mature technique and is widely applied in HV DC power systems. Static and dynamic voltage balance is ensured by shunting individual devices with dissipative snubbers. The snubber losses become pronounced for increased operating frequencies and adversely affect power density. Capacitive snubbers do not exhibit these disadvantages, but they require a zero-voltage switching mode. Super-resonant power converters facilitate the principle of zero-voltage switching. A high-voltage DC-DC power converter with multiple series-connected devices is proposed. It allows the application of nondissipating snubbers to assist the voltage sharing between the multiple series-connected devices and lowers turnoff losses. Simulation results obtained with a circuit simulator are validated in an experimental power converter operating with two series-connected devices. The behavior of the series connection is examined for MOSFETs and IGBTs by both experimental work with a 2 kW prototype and computer simulation. Applications can be found in traction and heavy industry, where the soft-switching power converter is directly powered from a high-voltage source     

The Future of Mixing Research

This paper is the result of a plenary discussion session held at the 11^th European Conference on Mixing. Three perspectives on mixing research are explored: that of the industrialist, the equipment manufacturer, and the academic researcher. There was strong agreement that, while the one dimensional problems are reasonably well understood and many engineers thus perceive that mixing is simple, current practice actually requires us to address complex, multi‐dimensional problems with interactions between mixing, reaction, multi‐phase physics, surface phenomena, and transport phenomena. Understanding these multi‐scale, multi‐mechanism problems requires models which include interactions between the phenomena, and allow the effects of these interactions to emerge. Developing these models will require us to shift our perspective on mixing from one of equipment design to one of the mixing field as a fundamental physical mechanism.