Effects of base layer thickness on reliability of CVD Si3N4 stack gate dielectrics

Effects of the base layer in Si₃N₄/SiON stack gate dielectrics, in particular, the physical thickness of the base layer, on the dielectric reliability, MOSFET performance and process controllability are investigated. It is found that the electrical characteristics such as TDDB lifetime as well as the Si₃N₄ film property in Si₃N₄/SiON stack dielectrics with the same capacitance oxide equivalent thickness strongly depend on the SiON-base layer thickness. From the TDDB measurements for both stress polarities and from the Si₃N₄ stoichiometry by the X-ray photoelectron spectroscopy analysis, the optimum SiON-base layer thickness is determined to be approximately 1 nm, in order to obtain longer TDDB lifetime and surperior n-ch MOSFET performance. The obtained results are considered to attribute to the nitrogen profile in the Si₃N₄/SiON stack dielectrics and the strained layer thickness near SiON/Si interface.     

船用柴油机NOx等有害排放气体的评价及处理研究--燃料喷射系统对乳化燃料在船用柴油机上使用的影响及脱硝装置的适用性

对原试验用柴油机的燃料喷射系统进行了改造。改造后的燃料喷射系统不仅可降低 NOx 的排放 ,而且使高加水率乳化燃料的使用成为可能。但另一方面 ,在低负荷时 ,使用乳化燃料不但不能获得预期的降低 NOx 排放效果 ,反而使其它有害排放增加。所以 ,也对降低 NOx 排放方法之一的脱硝装置进行了探讨 ,对其在船用柴油机上的适用性进行了试验 ,并获得了较好的效果     

Preparation and properties of TiN and AlN films from alkoxide solution by thermal plasma CVD method

Single phase TiN and AlN films were prepared on a Si wafer from titanium tetra-etoxide and aluminum tri-butoxide solutions dissolved in ethanol and toluene, respectively, using an Ar/N₂/H₂ radio-frequency (r.f.) inductive thermal plasma chemical vapor deposition (CVD) method. The films were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, measurement of electrical resistivity and Vickers microhardness. Factors affecting the formation of the films (lattice parameter, chemical composition, oxygen/carbon content, and deposition rate of the films) were examined in terms of the N₂ flow rate (2.5–4.5 slm), substrate temperature (300–700°C), feed rate of the solution (0.025–0.3 ml/min), and the mole ratio of the alkoxide solution (1:1–1:3). The optimum conditions for preparation of TiN films produced a film 0.2–3 μm thick with an oxygen content of 8 at.% and a free carbon content of 4 at.%, showing an electrical resistivity of 370 μΩ cm. The optimum conditions for AlN films produced a film 0.3 μm thick containing 14 at.% oxygen and 8 wt.% carbon. The deposition rate of the TiN film was determined to be 30–35 nm/min. The Vickers microhardness of the TiN and AlN films was found to be 10±1 and 13±3 GPa, respectively.     

Effect of fiber array irregularities on microscopic interfacial normal stress states of transversely loaded UD-CFRP from viewpoint of failure initiation

A detailed investigation has been carried out to determine the effect of local fiber array irregularities and controlling fiber distribution parameters on microscopic interfacial normal stress states for transversely-loaded unidirectional carbon fiber (CF)/epoxy composites. Linear elastic finite element analyses were carried out for two-dimensional image-based models composed of about 70 fibers. The relationship between the geometrical distribution of two adjacent fibers and the interfacial normal stresses (INSs) is investigated for all fibers in different image-based models. Three boundary conditions for loading were selected: Case A involved cooling from the curing temperature (the difference in temperature was ?155 K); Case B involved transverse loading of 75 MPa chosen as an example of macroscopic transverse fracture strength; and Case C involved both cooling from the curing temperature and transverse loading of 75 MPa. High compressive INSs due to the difference in the coefficients of thermal expansion are observed at the location of the shortest interfiber distance for Case A (cooling). High tensile INSs are observed at the location of the shortest interfiber distance and where the fiber alignment angle to the loading direction is small for Case B (loading). For Case C (cooling and loading), the high thermal residual compressive INSs and the high mechanical tensile INSs compensate each other, and the INSs at a short interfiber distance are much lower than those for Case B. These results clearly indicate the importance of the contribution of the thermal residual stresses to the transverse tensile failure initiation of CF/epoxy laminates.     

‘Springtecture’ B

Masaaki Takahashi describes a house, designed by Shuhei Endo, whose coiled corrugated-steel surface seamlessly unifies the inside with the outside, despite its surprisingly rural setting.     

Effect of Coarse-Powder Portion on Abnormal Grain Growth during Hot Pressing of Commercial-Purity Alumina Powder

By classification, two powder portions, one consisting of coarse particles and the other consisting of fine particles, were separated from a MgO-doped (1000 ppm) commercial-purity Al₂O₃ powder. Examinations of microstructure evolution during hot pressing showed that extensive abnormal grain growth occurred for the coarse portion. For the fine portion, although there was an indication that grain-size distribution deviated from normal distribution on prolonged hot pressing, such extensive abnormal grain growth did not occur. Extensive abnormal grain growth also occurred when the coarse portion was mixed into a high-purity powder that exhibited no abnormal grain growth alone. Chemical analyses revealed that the coarse portion contained the higher concentration of impurities but lower concentration of magnesium than the fine portion. It was discussed that particle aggregates in the coarse portion might have been responsible for the higher concentration of impurities but lower concentration of magnesium and, thus, for the extensive abnormal grain growth.     

Determination of residual avoparcin in chicken muscle by HPLC with ultraviolet and amperometric detection

An analytical method was developed for determination of residual avoparcin in chicken muscle by measuring alpha- and beta-avoparcin, major components of the pharmaceutical preparation avoparcin, using HPLC with UV and amperometric detectors. The analytical HPLC was run on a Cosmosil 5C18-AR column (4.6 mm x 25 cm) with a gradient formed from A: 2.5% acetic acid, 0.01 mol/L sodium heptane sulfonic acid-acetonitrile (88.5:11.5) (pH 4.0) and B: 2.5% acetic acid-acetonitrile (10:90), using UV and amperometric detection (AMD) with glassy-carbon electrode (+900 mV). Avoparcin was extracted from chicken muscle by homogenization with methanol-0.2 mol/L sulfuric acid (6:4) followed by centrifugation after pH adjustment to 4 with 1 mol/L sodium hydroxide. The supernatant was evaporated to dryness, and the residue was dissolved in water. The aqueous layer was adjusted to pH 4 by adding 1 mol/L sodium hydroxide. Then it was purified on a Sep-Pak tC18 plus ENV cartridge. The cartridge was washed with water, and retained substances were eluted with 50% methanol. The eluate was evaporated to dryness under reduced pressure. The residue was dissolved in water and determined by HPLC. Recoveries of avoparcin spiked in chicken muscle were 73.1-88.1% at levels of 2-10 micrograms/g. The detection limits were 0.5 microgram/g (UV) and 0.2 microgram/g (AMD).     

Metalloendopeptidase ADAM-like Decysin 1 (ADAMDEC1) in Colonic Subepithelial PDGFRα+ Cells Is a New Marker for Inflammatory Bowel Disease

Metalloendopeptidase ADAM-Like Decysin 1 (ADAMDEC1) is an anti-inflammatory peptidase that is almost exclusively expressed in the gastrointestinal (GI) tract. We have recently found abundant and selective expression of Adamdec1 in colonic mucosal PDGFRα⁺ cells. However, the cellular origin for this gene expression is controversial as it is also known to be expressed in intestinal macrophages. We found that Adamdec1 mRNAs were selectively expressed in colonic mucosal subepithelial PDGFRα⁺ cells. ADAMDEC1 protein was mainly released from PDGFRα⁺ cells and accumulated in the mucosal layer lamina propria space near the epithelial basement membrane. PDGFRα⁺ cells significantly overexpressed Adamdec1 mRNAs and protein in DSS-induced colitis mice. Adamdec1 was predominantly expressed in CD45⁻ PDGFRα⁺ cells in DSS-induced colitis mice, with only minimal expression in CD45⁺ CD64⁺ macrophages. Additionally, overexpression of both ADAMDEC1 mRNA and protein was consistently observed in PDGFRα⁺ cells, but not in CD64⁺ macrophages found in human colonic mucosal tissue affected by Crohn’s disease. In summary, PDGFRα⁺ cells selectively express ADAMDEC1, which is localized to the colon mucosa layer. ADAMDEC1 expression significantly increases in DSS-induced colitis affected mice and Crohn’s disease affected human tissue, suggesting that this gene can serve as a diagnostic and/or therapeutic target for intestinal inflammation and Crohn’s disease.     

Development and Evaluation of a Robust Sandwich Immunoassay System Detecting Serum WFA-Reactive IgA1 for Diagnosis of IgA Nephropathy

Aberrant glycosylation of IgA1 is involved in the development of IgA nephropathy (IgAN). There are many reports of IgAN markers focusing on the glycoform of IgA1. None have been clinically applied as a routine test. In this study, we established an automated sandwich immunoassay system for detecting aberrant glycosylated IgA1, using Wisteria floribunda agglutinin (WFA) and anti-IgA1 monoclonal antibody. The diagnostic performance as an IgAN marker was evaluated. The usefulness of WFA for immunoassays was investigated by lectin microarray. A reliable standard for quantitative immunoassay measurements was designed by modifying a purified IgA1 substrate. A validation study using multiple serum specimens was performed using the established WFA-antibody sandwich automated immunoassay. Lectin microarray results showed that WFA specifically recognized N-glycans of agglutinated IgA1 in IgAN patients. The constructed IgA1 standard exhibited a wide dynamic range and high reactivity. In the validation study, serum WFA-reactive IgA1 (WFA+-IgA1) differed significantly between healthy control subjects and IgAN patients. The findings indicate that WFA is a suitable lectin that specifically targets abnormal agglutinated IgA1 in serum. We also describe an automated immunoassay system for detecting WFA+-IgA1, focusing on N-glycans.     

Beta-1,3 Oligoglucans Specifically Bind to Immune Receptor CD28 and May Enhance T Cell Activation

Beta glucans are known to have immunomodulatory effects that mediated by a variety of mechanisms. In this article, we describe experiments and simulations suggesting that beta-1,3 glucans may promote activation of T cells by a previously unknown mechanism. First, we find that treatment of a T lymphoblast cell line with beta-1,3 oligoglucan significantly increases mRNA levels of T cell activation-associated cytokines, especially in the presence of the agonistic anti-CD3 antibody. This immunostimulatory activity was observed in the absence of dectin-1, a known receptor for beta-1,3 glucans. To clarify the molecular mechanism underlying this activity, we performed a series of molecular dynamics simulations and free-energy calculations to explore the interaction of beta-1,3 oligoglucans with potential immune receptors. While the simulations reveal little association between beta-1,3 oligoglucan and the immune receptor CD3, we find that beta-1,3 oligoglucans bind to CD28 near the region identified as the binding site for its natural ligands CD80 and CD86. Using a rigorous absolute binding free-energy technique, we calculate a dissociation constant in the low millimolar range for binding of 8-mer beta-1,3 oligoglucan to this site on CD28. The simulations show this binding to be specific, as no such association is computed for alpha-1,4 oligoglucan. This study suggests that beta-1,3 glucans bind to CD28 and may stimulate T cell activation collaboratively with T cell receptor activation, thereby stimulating immune function.