膨胀石墨对各种油类的吸附动力学

通过对吸附率(有效吸附系数)Ks和饱和吸附量msat的测量,描述了粘度为0.001 Pa·s～0.850 Pa·s的各种油类在膨胀石墨柱中的吸附动力学,发现吸附率Ks对油类粘度有很强的相关性.吸入膨胀石墨柱中的饱和吸附量msat几乎恒定在50kg/kg,该值略低于由膨胀石墨块直接浸渍在油中测得的吸附容量,这是由于所吸附的油沿膨胀石墨柱高度存在重力梯度.     

Characterization of temporal response, spectral responsivity and its spatial uniformity in photoconductive diamond detectors

Three photoconductive diamond detectors with highly oriented diamond (HOD) films fabricated by the same process were characterized with respect to temporal response, spectral responsivity and its spatial uniformity over the wavelength range from 190 to 250 nm. Temporal measurements showed a drift in the baseline, suggesting the presence of deep level carrier traps. The responsivity of specimen No. 2 was more than twice those of the other two specimens, but it showed an unpredictable current fluctuation. It was found that the spatial uniformities of all the specimens were too low for radiometric purposes. A prominent peak, thought to be due to photoemission, was found in the responsivity spatial distribution of specimen No. 3 under a negative applied voltage.     

Design of nonlinear controllers for active vehicle suspension with state constraints

Design of active vehicle suspension has tradeoffs between three main performance metrics (passenger comfort, suspension deflection and road holding ability). It has been known that each performance can be achieved by H _∞ controller and they can be gathered by LPV (Linear Parameter Varying) method. However, because the suspension deflection limit was not explicitly considered, this limit may be exceeded. In this paper, the authors propose a “reference shaping“ based method in order to improve the control performance. In this approach, a “virtual reference” signal is imposed to the system such that the suspension deflection is kept small. The effectiveness of the approach is examined by numerical simulations. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Suppression of photo-induced dilation in cyanide treated hydrogenated amorphous silicon films

Effects of cyanide (CN) treatment with hydrogenated amorphous silicon (a-Si:H) films have been investigated. The decrease of ΔV/V was observed in cyanide treated a-Si:H films and the successive thermal annealing at 200°C after CN treatment induced the further reduction of the ΔV/V. XPS spectra show the indirect evidence that the cyanide species is present within 10 nm from the hydrogenated amorphous silicon surface. The results of CN treatment with a-Si:H solar cells are demonstrated.     

Software‐processed edge‐ and level‐adaptive overdrive (SELAO) method for high‐quality motion pictures

Abstract— In this paper, a software‐processed edge‐ and level‐adaptive overdrive (SELAO) method, which is a novel overdrive technique that utilizes not only a temporal change of gray levels but also a spatial edge intensity of motion pictures, is proposed. The SELAO method is a software video‐processing technology to improve motion‐picture quality rendered on LCDs more than is possible with a conventional SLAO method without edge‐adaptive overdrive, and it works in real time on commonly used personal computers (PCs).     

An instantaneous response CMOS optical receiver IC with widedynamic range and extremely high sensitivity using feed-forwardauto-bias adjustment

An instantaneous response CMOS optical-receiver IC is described with wide input dynamic range and high sensitivity. In a TCM (time compression multiplexing)-TDMA (time division multiple access) fiber-optic subscriber system, a receiver should be able to handle burst-data packets with different amplitude. This requires quick response and a wide dynamic range. Instantaneous response is achieved with a new feed-forward auto-bias adjustment technique. In addition, multistaged offset compensation provides a wide dynamic range without any external elements and adjustments. Using these design techniques, an optical receiver IC was fabricated in a standard 0.8-μm CMOS technology. The receiver has a wide dynamic range of more than 25 dB for burst-mode optical input at 29 Mb/s. It has high transimpedance gain of 150 dBΩ and high sensitivity of -42 dBm with stable operation for FET threshold voltage and power supply voltage fluctuation     

Wide gamut LCD using locally dimmable four‐primary‐color LED backlight

This paper proposes a wide gamut LCD using locally dimmable four‐primary‐color (4PC) LED backlight. Although the color gamut of LCDs has been improved in recent years, it is insufficient to reproduce all the colors in the real world. The objective of this paper is to propose a wide gamut LCD that reproduces all the colors in the real world while keeping the cost increases to a minimum. We evaluated the color gamut reproduced by LEDs of multiple primary colors and selected cyan as the optimal color to be added to the three primary colors to reproduce all the colors in the real world. Therefore, we designed an LED backlight consisting of an additional only‐cyan LED with three‐primary‐color LEDs and developed a prototype LCD with 4PC LED backlight. Furthermore, we developed a local dimming algorithm for the 4PC LED backlight. As a result, we confirmed that the prototype LCD with the 4PC LED backlight is able to cover almost all the colors in the real world and also able to display natural images with highly saturated colors by local dimming.     

Preparation of zirconia-toughened bioactive glass-ceramics

Bioactive glass-ceramics toughened by tetragonal zirconia polycrystal (TZP) were prepared by hot-pressing mixed powders of the MgO-CaO-P₂O₅-SiO₂ glass and TZP containing 20 to 80% alumina. The bending strength and the fracture toughness of the composite materials were improved compared with those of the material without TZP. These composites showed high bending strengths (400 to 500MPa) and high fracture toughness ( 2.8MPa m^1/2). The existence of a crack deflection mechanism was observed by scanning electron microscopy. After soaking in simulated physiological solution at 100 °C, no phase transformation from tetragonal to monoclinic of TZP in the composites and no degradation in bending strength occurred.     

Selective oxidation of Fe-30Ni alloy in a low-temperature range (433–473 K)

Fe-30Ni alloy specimens were oxidized for 10–240 min at 433–473 K in pure oxygen at a pressure of 1.33×10⁴ Pa. The thickness of oxide films was measured by a multiple-angle-of-incidence ellipsometer. The kinetics of film growth were found to obey a parabolic rate law. The depth-profiling of oxidized surfaces, performed with simultaneous use of Auger electron spectroscopy (AES) and argon-ion sputter-etching technique, reveals that iron component is selectively oxidized and an iron-depeletion zone is formed in the underlying alloy. The thickness of the iron depletion zone increases with increasing oxidation time or oxidation temperature. During surface oxidation of the alloy, the transport rate of iron component in the film is almost equal to the interdiffusion rate in the underlying alloy, indicating the establishment of a steady state. The values of the interdiffusion coefficient, , of the underlying alloy estimated from the depth-composition profiles are more than 10 orders of magnitude as large as the values extrapolated from the lattice diffusion data of the corresponding alloy obtained at high temperature. The enormously large values of may be explained in terms of the vacancy (monovacancy or divacancy)-enhanced lattice diffusion mechanism.