Synthesis of poly(α-thiophenediyl)benzylidene with high molecular weight and its thermal stability

Summary The synthesis of poly(-thiophenediyl)benzylidene (PTB) with high molecular weight is described. Number-average degrees of polymerization reached about 74. The characterizations of the polymer was investigated by ¹H-NMR, ¹³C-NMR, IR, and UV-VIS spectra. The polymer with well-defined structure and high molecular weight was obtained by polymerization at low temperature and in polar solvent. This polymer was thermally stable and a thermal decomposition took place at 391°C under nitrogen and at 370°C under air. The glass transformation temperature was 117°C and this PTB was nonfusible.     

Mechanical Properties of Alumina/Silicon Carbide Whisker Composites

The improvement of mechanical properties of Al₂O₃/SiC whisker composites has been studied with emphasis on the effects of the whisker content and of the hot-pressing temperature. Mechanical properties such as fracture toughness and fracture strength increased with increasing whisker content up to 40 wt%. In the case of the high SiC whisker content of 40 wt%, fracture toughness of the sample hot-pressed at 1900° decreased significantly, in spite of densification, compared with one hot-pressed at 1850°. Fracture toughness strongly depended on the microstructure, especially the distribution of SiC whiskers rather than the grain size of the Al₂O₃ matrix.     

Synergistic effects of doped Fe3+ and deposited Au on improving the photocatalytic activity of TiO2

Fe³⁺ doped together with Au deposited TiO₂ (Au/Fe³⁺–TiO₂) was successfully prepared, which shows excellent photocatalytic activity for degradation of methyl orange (MO) under both UV and visible light (λ > 420 nm) illumination. Fe³⁺ has been confirmed by EPR to substitute for Ti⁴⁺ in the TiO₂ lattice, and Au exists as Au⁰ on the surface of the photocatalyst indicated by the results of XRD. Fe³⁺ and Au have synergistic effects on improving the photocatalytic activity of TiO₂. A proposed mechanism concerning the synergistic effects is discussed to explain the improvement of the photocatalytic activities.     

One-step formation of ethyl methyl ketone from 1-butene and water on ultrastable Y-type zeolite catalyst

Proton exchanged ultrastable Y-type zeolite with silica/alumina = 40 showed a pronounced catalytic activity for the formation of ethyl methyl ketone directly from 1-butene and water. The formation rate of ethyl methyl ketone was much higher than those on MoO₃-based catalysts in the oxidation of 1-butene by oxygen. It was suggested that the basic site necessary for the formation of ethyl ketone directly from 1-butene and water would be the pentacoordinated Al.     

Segmented conjugated polymer based on poly(α-thiophenediyl)benzylidine

Summary Segmented polymers with random sequences of conjugated and non-conjugated blocks are produced by partial dehydrogenation of poly(-thiophenediyl)benzylidene. The fraction of conjugated block was controlled by the elimination time. The polymers gave photoluminescence. Absorption coefficients of the polymers increased with the rate of dehydrogenation, and the highest fluorescence intensity were achieved around 9 % conjugation conversion. The polymers were characterized by ¹H- and ¹³C-n.m.r. and infrared spectra, and were soluble in common organic solvents, which suggests a good processability.     

Microstructure Control of Thermally Sprayed Co-Based Self-Fluxing Alloy Coatings by Diffusion Treatment

This article describes microstructure control aimed for wear-resistance improvement of Co-based (Co-Cr-W-B-Si) self-fluxing alloy coating by diffusion treatment. The diffusion treatments of thermally sprayed Co-based self-fluxing alloy coating on steel substrate were carried out at 1370-1450 K for 600-6000 s under an Ar gas atmosphere. Microstructural variations of the coating and the interface between the substrate and the coating were investigated in detail. A proper diffusion treatment precipitates two kinds of fine compounds in Co-based matrix. X-ray diffractometer (XRD) and electron probe microanalyzer (EPMA) analysis revealed these precipitates to be a chromium boride dissolving cobalt and a tungsten boride containing cobalt and chromium. The size of each precipitate became larger with increasing treatment temperature and time. A coating with the proper size borides showed a superior wear-resistance. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

Analysis of accelerated creep under constant sustaining load for austenitic stainless steels

The effect of stress on creep rate of austenitic stainless steels of type 347 and 316 was studied by applying the differential test technique. It was found that the creep rate could be expressed as follows, whereB ₁ is a material constant depending on temperature,a ₁ anda _o are constants, and σ is the real stress. Considering the increase in real stress during creep process due to void formation and to the decrease in cross sectional area of the specimen, integrating the above equation yields the following creep curve, 1 $$ \in = \in _m + \frac{1}{{n_o \left( {c_o + 1} \right)}}ln\frac{1}{{1 - n_o \left( {c_o + 1} \right) \in _m (t - t_{_m } )}}$$ where ∈ is the creep strain at a given time (t), ∈_m is the minimum creep rate, ∈_m andt _m are the strain and time, respectively, at the minimum creep rate,n _o is a constant, andc _o is the material constant relating to the void formation. This equation agrees very well with the experimental creep curve.     

Grain refinement and superplasticity in a magnesium alloy processed by equal-channel angular pressing

The extrusion/equal channel angular pressing (EX-ECAP) processing procedure, in which magnesium-based alloys are subjected to extrusion followed by ECAP, was applied to a Mg-7.5 pct Al-0.2 pct Zr alloy prepared by casting. Microstructural inspection showed the EX-ECAP process was effective in reducing the grain size from ∼21 μm after extrusion to an as-pressed grain size of ∼0.8 μm. It is shown through static annealing that these ultrafine grains are reasonably stable up to 473 K, but grain growth occurs at higher temperatures. Tensile specimens were cut from the billets prepared by EX-ECAP and testing showed these specimens exhibited superplasticity at relatively low temperatures with maximum elongations up to >700 pct. By processing through EX-ECAP to a higher imposed strain and thereby increasing the area fraction of high-angle boundaries, it is demonstrated that there is a potential for achieving high-strain-rate superplasticity. This article is based on a presentation made at the Symposium entitled “Phase Transformations and Deformation in Magnesium Alloys,” which occurred during the Spring TMS meeting, March 14–18, 2004, in Charlotte, NC, under the auspices of the ASM-MSCTS Phase Transformations Committee.     

Achieving enhanced ductility in a dilute magnesium alloy through severe plastic deformation

Experiments were conducted to evaluate the utility of a new processing procedure developed for Mg-based alloys in which samples are subjected to a two-step processing route of extrusion followed by equal-channel angular pressing (designated as EX-ECAP). The experiments were conducted using a Mg-0.6 wt pct Zr alloy and, for comparison purposes, samples of pure Mg. It is shown that the potential for successfully using ECAP increases in both materials when adopting the EX-ECAP procedure. For the Mg-Zr alloy, the use of EX-ECAP produces a grain size of ∼1.4 μm when the pressing is undertaken at 573 K. By contrast, using EX-ECAP with pure Mg at 573 K produces a grain size of ∼26 μm. Tensile testing of the Mg-Zr alloy at 523 and 573 K after processing by EX-ECAP revealed the occurrence of significantly enhanced ductilities with maximum elongations of ∼300 to 400 pct.     

Bone Tissue Engineering in Rat Calvarial Defects Using Induced Bone-like Tissue by rhBMPs from Immature Muscular Tissues In Vitro

This study aimed to induce bone-like tissue from immature muscular tissue (IMT) in vitro using commercially available recombinant human bone morphogenetic protein (rhBMP)-2, rhBMP-4, and rhBMP-7, and then implanting this tissue into a calvarial defect in rats to assess healing. IMTs were extracted from 20-day-old Sprague-Dawley (SD) fetal rats, placed on expanded polytetrafluoroethylene (ePTFE) with 10 ng/μL each of rhBMP-2, BMP-4, and BMP-7, and cultured for two weeks. The specimens were implanted into calvarial defects in 3-week-old SD rats for up to three weeks. Relatively strong radiopacity was observed on micro-CT two weeks after culture, and bone-like tissue, comprising osteoblastic cells and osteoids, was partially observed by H&E staining. Calcium, phosphorus, and oxygen were detected in the extracellular matrix using an electron probe micro analyzer, and X-ray diffraction patterns and Fourier transform infrared spectroscopy spectra of the specimen were found to have typical apatite crystal peaks and spectra, respectively. Furthermore, partial strong radiopacity and ossification were confirmed one week after implantation, and a dominant novel bone was observed after two weeks in the defect site. Thus, rhBMP-2, BMP-4, and BMP-7 differentiated IMT into bone-like tissue in vitro, and this induced bone-like tissue has ossification potential and promotes the healing of calvarial defects. Our results suggest that IMT is an effective tissue source for bone tissue engineering.