Mesophase structure discovered through in-situ X-ray measurement in drawing process of poly(ethylene 2,6-naphthalene dicarboxylate) fiber

The structure development in the continuous laser-heated drawing process of poly(ethylene 2,6-naphthalene dicarboxylate) (PEN) fiber was analyzed by in-situ X-ray diffraction measurement. Because of the rapid and uniform laser heating, and the resultant steady-state nature of the necking-drawing, the structure development after the on-set of necking could be measured in the time resolution of several hundred microseconds. We found for the first time the temporal appearance of meridional (001′) diffraction at several milliseconds after the on-set of necking indicating that the mesophase structure similar to the one reported for poly(ethylene terephthalate) was also formed in the initial stage of fiber structure development of PEN. The d-spacing of the (001′) diffraction 1.230 ± 0.003 nm was shorter than the c-axis lengths of both α and β crystals.     

ASYMPTOTIC EFFICIENCY OF THE SAMPLE COVARIANCES IN A GAUSSIAN STATIONARY PROCESS

Abstract. This paper deals with the asymptotic efficiency of the sample autocovariances of a Gaussian stationary process. The asymptotic variance of the sample autocovariances and the Cramer–Rao bound are expressed as the integrals of the spectral density and its derivative. We say that the sample autocovariances are asymptotically efficient if the asymptotic variance and the Cramer–Rao bound are identical. In terms of the spectral density we give a necessary and sufficient condition that they are asymptotically efficient. This condition is easy to check for various spectra.     

DRYING OF OPTICALLY SEMITRANSPARENT MATERIALS BY COMBINED RADIATIVE-CONVECTIVE HEATING

The objective of this work has been to basically elucidate the drying characteristics of an optically semitransparent material by combined radiative and convective heating. The experiments were conducted for a graphite suspension, a slurry of surplus activated sludge and a wet silica sand. The time-change of the drying rate as well as of the surface temperature of the brimfully wet material layer were measured under the step heating conditions using an infrared lamp bundle and a blast of hot air heated by an electric heater.

The experimental data obtained show satisfactory agreement with the calculated results from unsteady heat and mass transfer equations derived on the basis of a semitransparent drying model during the preheating and the constant drying rate periods.     

EFFECT OF INTERMITTENT HEATING ON DRYING-INDUCED STRAIN-STRESS OF MOLDED CLAY

ABSTRACT

Parametric analyses of the strain-stress in the drying process are performed to study the influence of the intermittent drying on the behaviors of drying-induced strain-stress and deformation as well as the drying characteristic. The transient three-dimensional problem of strain-stress and heat and moisture transfer in a slab is solved simultaneously by the finite element method. The dimensionless parameters are introduced to generalize the problem in the conservation equations of heat and moisture transfer. The intermittent drying is modeled by applying periodically smaller and larger Biot numbers to the boundary conditions. The maximum tensile and compressive stresses fluctuate, and fall remarkably during the smaller Biot number period when a slab is heated intermittently. The peak stress of the fluctuation exceeds beyond the case in the continuous healing where the overall drying rate is almost equivalent to that in the intermittent beating, but the reduction of the stresses takes place rapidly in the low heating period.     

Acid-dyeable acrylic fibres copolymerised with amino alkyl methacrylates for differential cross-dyeing

The equilibrium adsorption of acid dyes on acrylic fibres copolymerised with dimethyl amino ethyl methacrylate has been investigated. A typical characteristic of this type of fibre is its excellent stable dyeability over a wide pH range. This is due to the strong basicity of alkylamino groups in the copolymerised component, which makes it possible to dye the fibre thoroughly even in a weakly acidic dyebath using a normal dyeing processes of acrylic fibre with cationic dye. Consequently it is useful for differential cross-dyeing in a single dyebath.     

DRYING OF CLAY AND NONCLAY MEDIA : HEAT AND MASS TRANSFER AND QUALITY ASPECTS

The researches on drying of clay and nonclay media are briefly reviewed and the role of drying in the manufacturing process is summarized. The drying process must be carefully controlled to maintain the desired product configuration. Inefficient completion of drying and poor operation of the dryer influence directly the product quality. The importance of R&D on the heat and moisture transfer phenomena, shrinkage mechanisms, deformation behavior, strain-stress relations and the internal pressure in the media during drying is stressed. Suggestions are given for further improvement of the drying process and improved design of the molding and casting processes for higher product quality     

R & D Needs - Drying of Ceramics

ABSTRACT

New research and development needs for the drying of ceramics are prooosed. The researches on the ceramic drying are briefly reviewed and the role of the drying in the ceramic production process iS summarized. The drying must deal with molded materials and the problem is of significant difference from another drying with particulate materials. It means that the drying must be performed with keeping the molded feature and the insufficient completion of drying and the careless operation influence directly on the product quality The importnance of the R & D on the heat and moisture transfer. shrinking mechanism. the deformation behavior and the strain-stress formation in the molded clay issuggested. The subjects are also pointed out for the further improvement of the ceramic drying process and the precise design of molding with high quality.     

Programmed High‐Hole‐Mobility Supramolecular Polymers from Disk‐Shaped Molecules

In this paper a simple, casting solution technique for the preparation of two‐dimensional (2D) arrays of very‐high molecular weight (MW) 1D‐Pc supramolecular inorganic polymers is described. The soluble fluoroaluminium tetra‐tert‐butylphthalocyanine (ttbPcAlF) is synthesized and characterized, which can be self‐assembled to form 2D arrays of very‐high‐MW 1D‐Pc supramolecular inorganic polymers. High‐resolution transmission electron microscopy (HRTEM) demonstrates that the 1D‐ttbPcAlF, having a cofacial ring spacing of ～0.36 nm and an interchain distance of ～1.7 nm, self‐assembles into 2D‐nanosheets (～140 nm in length, ～20 nm in width, and equivalent to MW of 3.2 × 10⁵ g mol^?1). The film cast from a 1,2‐dichloroethane (DCE) solution shows a minimum hole‐mobility of ～0.3 cm² V^?1 s^?1 at room temperature by flash‐photolysis time‐resolved microwave conductivity (TRMC) measurements and a fairly high dark dc‐conductivity of ～1 × 10^?3 S cm^?1.