Enzymatic modification of canola/palm oil mixtures: Effects on the fluidity of the mixture

The bioreactor system to interesterify edible oils and fats at an ultra-micro aqueous phase of 100 ppm and less was investigated. The adsorption of lecithin, together with lipase onto a carrier, was effective for conducting the interesterifying reaction efficiently for oils and fats in micro aqueous phase. To improve the handling properties of palm oil at rather low temperature, palm oil was blended with canola or soybean oil, and then these blended oils were modified by enzymatic selective interesterification in a solvent-free, ultra-micro aqueous bioreactor system with an immobilized lipase that had 1,3-positional specificity. The effects of enzymatic interesterification were confirmed by triglyceride determination, by solid fat content profiles and by cloud point profiles, which were also compared to products of chemical interesterification. The improvement in the fluidity of blended oils with canola oil by the enzymatic reaction was bigger than with soybean oil, and chemical interesterification had no effects on the fluidity of blended oils.     

Oxide ion conduction in the sintered oxides of MoO3-doped Bi2O3

In order to examine the conduction behaviour in the sintered oxides of MoO₃-doped Bi₂O₃, the electrical conductivity in air and the EMF of oxygen gas concentration cell were measured with respect to the phase relation determined by X-ray diffraction.The tetragonal single phase oxide containing 22 mol% MoO₃ was found to be a high oxide ion conductor, the conductivity of which was comparable to those of stabilized zirconias. The partial electronic conduction in this phase was negligibly small at relatively high oxygen pressure. The oxide ion conduction was considered to be attributable to an appreciable amount of oxygen vacancies present in the crystal. In the monoclinic compound 3Bi₂O₃·2MoO₃, the oxide ion conduction was also observed. Although the conductivity of this phase was somewhat lower than that of the tetragonal phase, the activation energy for conduction (53·5 kJ mol^–1) was much lower than the values for usual oxide ion conductors.     

Aging and availability of binocular disparity and pictorial depth cues in 3D graphics contents

Some stereoblind observers do not perceive depth of 3D stimuli that depends on binocular disparity. These individuals, who have no disabilities, comprise over 5% of the general population. In addition, 17–30% of nonstereoblind young and young–middle people do not use disparity information in certain 3D environments, a phenomenon known as pseudo‐stereoblindness. This study aimed to investigate the relationship between aging and the proportion of pseudo‐stereoblindness in the general population. In an experiment, 134 nonstereoblind participants, ranging in age from 17 to 83 years, judged subjective depth of 3D stimuli containing binocular disparity and pictorial depth cues. Results showed that the proportion of pseudo‐stereoblindness among young (17–24 years old) and young–middle aged observers (25–39 years old) was 29%, in both cases. However, the proportion of pseudo‐stereoblind observers increased in older populations: 65% and 82% in the middle (40–54 years old) and senior (55–83 years old) age groups, respectively. These results suggest that a number of people, especially in elderly populations, have trouble perceiving depth from binocular disparity in 3D graphic contents despite their essential ability to use disparity information.     

Shear-rate dependence of first normal stress difference of poly(isoprene-b-styrene) in solution near the order-disorder transition temperature

Viscoelastic properties of poly(isoprene-b-styrene) in dioctylphthalate under steady shear flow were measured near the order—disorder transition temperature. In ordered states, first normal stress difference N₁ is proportional to shear rate at low region, but becomes proportional to at the high region, similar to the N₁ behaviour of polymer blends undergoing shear-induced homogenization. Because the existence of microdomains was confirmed at the high region by the flow birefringence method, it is concluded that the above N₁ behaviour is not caused by shear-induced homogenization, but is probably caused by the shear-induced alignment of the microdomain structure.     

Selective detection of acetylene gas extracted from isolation oil by an electrochemical sensor using a gold electrode

The selective detection of acetylene in gases extracted from isolation oils has been studied to develop an electrochemical sensor for the diagnostic monitoring of the condition of in-service electrical instruments. Effects of coexisting gases (CH₄, C₂H₆, C₂H₄, H₂ and CO) on the oxidation current of C₂H₂ were tested using gas-permeable gold-coated and platinum-black electrodes as the sensor. The gold-coated electrode showed good behaviour for the selective current detection of acetylene under potentiostatic conditions (−0.1 V/Pt-black reference electrode) in 10m H₂SO₄ electrolyte solution.     

The polymerization and copolymerization of nitroalkyl acrylates and nitroalkyl methacrylates

Nitroalkyl acrylates and methacrylates involving some new compounds were prepared. The homopolymerization of these monomers in toluene and their copolymerization with styrene in acetone were carried out with azobisisobutyronitrile as initiator. The rate of polymerization of the nitroalkyl acrylates showed a correlation with the number of nitro groups situated on the ester side chain. The apparent activation energies of the polymerization were found to be 22.0–27.5 kcal./mole for the nitroalkyl acrylates and about 11.5–13.0 kcal./mole for the nitroalkyl methacrylates. From the reactivity ratios and Q-e values of the copolymerization the following information was obtained. The copolymerization behavior of nitroalkyl acrylates and methacrylates showed an alternating tendency, and these monomers belong to the conjugative monomer groups. On the reactivities of these monomers, the polarity of vinyl group was affected a little by nitro group of ester bond side, and the resonance affected little. These monomers were crosslinked with 2-methyl-2-nitro-1,3-propylene diacrylate. Some of the polymers showed marked improvement in the physical properties of elastomers.     

Structural characterization of 1,2-polybutadiene by 13C-n.m.r. spectroscopy: 2. Sequence distribution of 1,2-unit in hydrogenated polybutadienes

The configurational sequences of 1,2-unit in a series of hydrogenated syndiotactic 1,2-polybutadienes were determined in relation to the sequence distribution of 1,2- and 1,4-units on the basis of the ¹³C-n.m.r. signal assignment of the methyl carbons. The observed triad distributions of 1,2- and 1,4-units and configurational distributions of the 1,2-unit are in good agreement with the calculated distributions from transition probabilities. The number average sequence lengths of the 1,2-unit and the 1,2-unit in the racemic addition are 5.7 to 8.0 and 4.1 to 5.4, respectively. From the extrapolation of the plot of the number average sequence length against the crystallinity of the starting 1,2-polybutadienes, the minimum sequence length for crystallization is estimated to be 3.7 for the 1,2-unit in the racemic addition.     

Influence of chromium on the local structure and morphology of ferric oxyhydroxides

The extended X-ray absorption fine structure (EXAFS) method and transmission electron microscopy (TEM) have been used for characterizing the local structure and morphology of ferric oxyhydroxides, α-FeOOH and γ-FeOOH, with and without chromium. These ferric oxyhydroxide powders were prepared from aqueous solutions containing iron and chromium ions. Radial structural functions for iron obtained by Fe K edge EXAFS spectra showed that the linkage of structural units formed by FeO₆ octahedra in γ-FeOOH is distorted by chromium addition, while such distortion in α-FeOOH is not clearly detected. On the other hand, Cr K edge EXAFS spectra showed that the local structure around chromium does not necessarily correspond to the local structure around of iron, which is observed by Fe K edge EXAFS spectra. This suggests that the structural units containing iron and chromium are heterogeneously distributed in these ferric oxyhydroxides. The local structural information was discussed coupled with morphological features of these ferric oxyhydroxides observed by TEM.     

Implicit Formulation for SPH‐based Viscous Fluids

We propose a stable and efficient particle‐based method for simulating highly viscous fluids that can generate coiling and buckling phenomena and handle variable viscosity. In contrast to previous methods that use explicit integration, our method uses an implicit formulation to improve the robustness of viscosity integration, therefore enabling use of larger time steps and higher viscosities. We use Smoothed Particle Hydrodynamics to solve the full form of viscosity, constructing a sparse linear system with a symmetric positive definite matrix, while exploiting the variational principle that automatically enforces the boundary condition on free surfaces. We also propose a new method for extracting coefficients of the matrix contributed by second‐ring neighbor particles to efficiently solve the linear system using a conjugate gradient solver. Several examples demonstrate the robustness and efficiency of our implicit formulation over previous methods and illustrate the versatility of our method.     

Cylindrical coils created with 3D X-ray lithography and metallization

The demand for microactuators is increasing recently. The key technology to realizing practical microactuators is microfabrication process. In the production of microminiature components, the technologies for processing high-aspect-ratio structures are essential. As one of these technologies, the LIGA process is widely known. Our laboratory researches the LIGA process to three-dimensional microfabrication and established the cylindrical-microcoil production process. In this paper, we have fabricated the cylindrical-microcoil for the solenoidal electromagnetic type microactuator. We designed and analyzed microactuators, and fabricated and evaluated microactuator coils produced by the combination of three-dimensional X-ray lithography and level copper plating. We succeeded in creating threaded groove-shaped structures with 10 μm line width, 20 μm pitch, and aspect ratio of 5 on the surface of an acrylic pipe by means of three-dimensional X-ray lithography. As a measure to suppress void generation, which is one of the shortcomings of electrolytic plating processes, the sputtering apparatus and plating equipment were improved, a pretreatment process was additionally provided, and the actual electrolytic plating method was improved. As a result, a void-free metallic deposit could be formed on a thin coil line. The processing technology enables the formation of thin-wire coil lines whose current paths feature a large allowable current-carrying capacity, enabling the production of miniature, high-output microactuators.