Thin-Film Thermoelectric Modules for Power Generation Using Focused Solar Light

We demonstrated the fabrication of thin-film thermoelectric generators and evaluated their generation properties using solar light as a thermal source. Thin-film elements of Bi_0.5Sb_1.5Te₃ (p-type) and Bi₂Te_2.7Se_0.3 (n-type), which were patterned using the lift-off technique, were deposited on glass substrates using radiofrequency magnetron sputtering. After annealing at 300°C, the average Seebeck coefficients of p- and n-type films were 150???V/K and ?104???V/K, respectively, at 50°C to 75°C. A cylindrical lens was used to focus solar light to a line shape onto the hot side of the thin-film thermoelectric module with 15 p?Cn junctions. The minimum width of line-shaped solar light was 0.8?mm with solar concentration of 12.5 suns. We studied the properties of thermoelectric modules with different-sized p?Cn junctions on the hot side, and obtained maximum open voltage and power values of 140?mV and 0.7???W, respectively, for a module with 0.5-mm p?Cn junctions. The conversion efficiency was 8.75?×?10^?4%, which was approximately equal to the value estimated by the finite-element method.     

Development of High Count Rate TES Microcalorimeters

To realize new TES imaging for high energy X-ray or gamma-ray spectrometer with a large pixel array and high count rate, we will try to develop a new radiation absorber self-adjusting the operating temperature and adopting an original reading out method of large pixel array using parallel biasing scheme. Our first prototype TES pixel using Au/Ti/Au tri-layer which consists of the small heat sensors and the radiation absorption area, and these are biased in serial. In this device, the current pulse with the decay time constant of less than 20 microseconds of incident X-rays from ⁵⁵Fe source were observed.      

Error grid analysis of noninvasive glucose monitoring via gingival crevicular fluid.

In order to realize a noninvasive blood glucose monitor, we monitored the gingival crevicular fluid (GCF). In this paper, the clinical evaluations were performed on not only normal subjects but also diabetic subjects using a GCF-glucose monitor to determine blood glucose levels. Meal load tests were carried out and the time-course changes in blood glucose level and GCF glucose level were measured continuously. A positive correlation of more than 0.9 was found between blood glucose level and GCF glucose level, necessitating the calibration of individual correlations for every subject. Finally, the performance of the GCF-glucose monitor was evaluated using Error Grid Analysis. As the results, significant information for the glucose level decision was obtained not only for normal subjects, but also for diabetic subjects.     

Seismic proof test of a reinforced concrete containment vessel (RCCV): Part 1: Test model and pressure test

In Japan, the Nuclear Power Engineering Corporation (NUPEC), sponsored by the Ministry of Economy, Trade and Industry (METI), has been conducting a series of seismic reliability proving tests using full-scale or close to full-scale models to simulate actual important equipment that is critical for seismic safety of nuclear power plants. The tests are intended to validate the seismic design and reliability with a sufficient margin even under destructive earthquakes. A series of tests was carried out on a reinforced concrete containment vessel (RCCV) for advanced boiling water reactor (ABWR) from 1992 to 1999. A large-scale high-performance shaking table at Tadotsu Engineering Laboratory, the largest in the world, was used for this test. Part 1 reports the test model and the results of pressure and leak tests. Part 2 describes test procedures, input waves and the results of verification tests such as changes of stiffness, characteristic frequency and damping ratio, the failure of the model and the load deflection. Part 3 shows the seismic safety margin that was evaluated from the energy input during the failure test to a design basis earthquake. Part 4 reports simulation analysis results by a stick model with lumped masses.     

Radiation induced synthesis of Au-Pd nanoparticles of random alloy structure supported on carbon particles using the high energy electron beam

Au-Pd bimetallic nanoparticles supported on carbon particles were synthesized by reduction of precursor ions in an aqueous solution irradiated with a high energy electron beam. The composition of the samples was analyzed by the inductively coupled plasma atomic emission spectrometry (ICP-AES), and the morphology of the samples was observed by the transmission electron microscope (TEM). TEM micrographs indicated that Au-Pd particles of ca. 5-nm were well dispersed on the surface of carbon particles of ca. 30-nm without any serious agglomeration. Addition of citric acid to the initial solution and high pH were found to be effective for formation of random alloy structure in the resultant bimetallic nanoparticles. The change in the bimetallic structure from core-shell to random alloy was identified by techniques of the X-ray diffraction (XRD) and the extended X-ray absorption fine structure (EXAFS).     

950 keV, 3.95 MeV and 6 MeV X-band linacs for nondestructive evaluation and medicine

We are developing compact X-band linac X-ray sources for nondestructive evaluation and medicine. First, we develop a portable X-ray system by a 950 keV 9.4 GHz X-band linac to realize on-site inspection. We use a low power (250 kW) magnetron as an RF source for compactness of the whole system. Since the RF power source is quite small and the stored energy in the structure is also small, we faced the problem of beam loading and current/RF-power oscillation. We are analyzing the problem by the circuit model. We plan to use this system for erosion inspection of metal pipes of petrochemical complex. By adopting a side-coupling cavity design to avoid the oscillation, we have developed 6 MeV X-band (9.3 GHz) linac for pinpoint dynamic tracking cancer therapy. Furthermore, we are manufacturing 3.95 MeV X-band (9.3 GHz) linac X-ray source with flexible waveguides for on-site bridge inspection. Updated results and situations are presented.     

Enhancement of optical absorption for below 5 μm thin-film poly-Si solar cell on glass substrate

Optical confinement effect of thin-film polycrystalline-Si (poly-Si) solar cell on glass substrate fabricated at low-temperature has been investigated as a function of cell thickness of less than 5 μm. We found that it is possible to fabricate the textured Si thin film in situ on a glass substrate and that the reflectance at long-wavelength light is reduced by surface texturing. Thin-film poly-Si solar cell and a-Si:H/(0.45 μm)/poly-Si (5 μm) tandem solar cell exhibit the efficiency of 8.6% and 12.8%, respectively. The numerical study in terms of the light trapping explains the excellent high short-circuit current density (_sc above 27 mA/cm² at the 4.7 μm thin-film poly-Si solar cell.     

Benzobisthiazole as Weak Donor for Improved Photovoltaic Performance: Microwave Conductivity Technique Assisted Molecular Engineering

New donor–acceptor‐type copolymers comprised of benzobisthiazole (BBTz) as a weak donor rather than acceptor are proposed. This approach can simultaneously lead to deepening the HOMO and LUMO of the polymers with moderate energy offset against fullerene derivatives in bulk heterojunction organic photovoltaics. As a proof‐of‐concept, BBTz‐based random copolymers conjugated with typical electron acceptors: thienopyrroledione (TPD) and benzothiadiazole (BT) based on density functional theory calculations are synthesized. Laser‐flash and Xe‐flash time‐resolved microwave conductivity (TRMC) evaluations of polymer:[6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) blends are conducted to screen the feasibility of the copolymers, leading to optimization of processing conditions for photovoltaic device application. According to the TMRC results, alternating BBTz‐BT copolymers are designed, exhibiting extended photoabsorption up to ca. 750 nm, deep HOMO (–5.5 to –5.7 eV), good miscibility with PCBM, and inherent crystalline nature. Moreover, the maximized PCE of 3.8%, the top‐class among BBTz‐based polymers reported so far, is realized in an inverted cell using TiO_x and MoO_x as the buffer layers. This study opens up opportunities to create low‐bandgap polymers with deep HOMO, and shows how the device‐less TRMC evaluation is of help for decision‐making on judicious molecular design.     

Increased Synovial CD14 mRNA Expression and Proportion of CD14high Subsets in Early-Stage Hip Osteoarthritis: Propensity Matched Score Analysis

The pathophysiology of early-stage hip osteoarthritis (EOA) is not fully understood. Although a previous study in an age-unmatched cohort reported that the number of macrophages was increased in knee EOA compared to late OA (LOA), it remained unclear whether increased macrophages in EOA accurately reflect EOA pathology. We investigated the differences in CD14 expression levels between EOA and LOA using age-unmatched and -matched cohorts. Synovial tissues were obtained from 34 EOA (Tönnis grades 0 and 1) and 80 LOA (Tönnis grades 2 and 3) patients. To correct for differences in demographics between patients with LOA and EOA, we also created propensity score-matched cohorts (16 EOA and 16 LOA). CD14 expression and its association with pain was estimated in LOA and EOA before and after propensity matching. We performed flow cytometry on tissues from the 16 patients, with 8 from each group, to assess for CD14+ subsets in the cells. The CD14 expression in EOA was higher than that in LOA both before and after propensity matching. The proportion of CD14^high subsets in EOA was higher than that in LOA. The CD14 expression was associated with pain in EOA before matching. However, no difference was observed between the pain and CD14 expression after matching in EOA. The increased CD14 expression and the proportion of CD14^high subsets may be important features associated with hip EOA pathology. To accurately compare early and late OA, the analysis of a propensity score-matched cohort is necessary.     

Application of the generalized body-fixed coordinate system for the wave-body interaction problem of a small-depth elastic structure in head seas

The body-fixed coordinate system is applied to the wave-body interaction problem of a small-depth elastic structure which has both rigid and elastic body motion...