Surface degradation of polyamide nanocomposites caused by partial discharges using IEC (b) electrodes

Partial discharge (PD) degradation of polyamide both without nanoscale fillers (nanofillers) and with 2,4 and 5 wt% additions of nanofillers was investigated. Such materials were subjected to PDs using the IEC (b) electrodes for evaluation. Comparisons were made as to the surface roughness observed by scanning electron microscopy and atomic force microscopy. It was found that the change in the surface roughness is far smaller in specimens with nanofillers than those without nanofillers, and that the 2 wt% addition is sufficient for improvement of the surface roughness. Furthermore, it was elucidated that the difference of surface roughness of the degraded area due to PDs among the specimens originates from the difference in their crystalline structures. These results indicate that polyamide nanocomposite is more resistance to PDs than polyamide without nanofillers.     

Transfer of semicrystalline polymers sliding against a smooth steel surface

The interrelationships between transfer and wear in polymers were studied using a pin-disk-type wear testing apparatus. The wear rates of polymers except polytetrafluoroethylene (PTFE) were high for up to about the first 100 revolutions of the disk and decreased gradually until the steady low wear rates which generally occurred after about 2000 revolutions. However, PTFE exhibited an almost constant high wear rate throughout the wear process. The thickness of transferred polymer increased rapidly with increasing number of revolutions in the initial wear stage but after about several hundred revolutions remained constant. A coherent transfer film was formed in most parts of the friction track after about 100 revolutions. It was found that polymer wear could occur in polymers sliding on a transferred polymer layer. All polymers except PTFE exhibited smaller wear rates when sliding on the transferred layer. The load dependence of the thickness was very small compared with that of the wear rate. PTFE produced a very dense and coherent transferred layer compared with that of other polymers. However, there was no clear relationship between friction and the thickness of the transferred polymer layer.     

Psychological Stress Exacerbates Inflammation of the Ileum via the Corticotropin-Releasing Hormone-Mast Cell Axis in a Mouse Model of Eosinophilic Enteritis

The effects of psychological stress on eosinophilic gastrointestinal disorders have not been elucidated. This study investigated the effects of psychological stress in a mouse model of eosinophilic enteritis (EoN). BALB/c mice were treated with ovalbumin (OVA) to create an EoN model and subjected to either water avoidance stress (WAS) or sham stress (SS). Microscopic inflammation, eosinophil and mast cell counts, mRNA expression, and protein levels of type 2 helper T cell (Th2) cytokines in the ileum were compared between groups. We evaluated ex vivo intestinal permeability using an Ussing chamber. A corticotropin-releasing hormone type 1 receptor (CRH-R1) antagonist was administered before WAS, and its effects were analyzed. WAS significantly increased diarrhea occurrence and, eosinophil and mast cell counts, and decreased the villus/crypt ratio compared to those in the SS group. The mRNA expression of CRH, interleukin IL-4, IL-5, IL-13, eotaxin-1, and mast cell tryptase β2 significantly increased, and the protein levels of IL-5, IL-13, and OVA-specific immunoglobulin E (IgE) also significantly increased in the WAS group. Moreover, WAS significantly increased the intestinal permeability. The CRH-R1 antagonist significantly inhibited all changes induced by WAS. Psychological stress exacerbated ileal inflammation via the CRH-mast cell axis in an EoN mouse model.     

Deep Phenotyping of Superficial Epidermolytic Ichthyosis due to a Recurrent Mutation in KRT2

Superficial epidermolytic ichthyosis (SEI) is an autosomal dominant inherited ichthyosis. SEI is caused by mutations in KRT2 and frequently shows erythroderma and widespread blistering at birth. We report the clinical manifestations of two patients from a Japanese family with SEI caused by a hotspot mutation, p.Glu487Lys, in KRT2. In addition, we summarize previous reports on SEI patients with the identical mutation. One of the two patients had disease onset at the age of 7 months. The other patient’s age of onset is unknown, but it was in childhood. Neither of the two patients showed erythroderma. To perform deep phenotyping, we studied the age of onset and the frequency of erythroderma in 34 reported SEI cases with the p.Glu487Lys mutation, including the present cases. Among the cases with sufficient clinical information, 44.4% of the cases that were due to p.Glu487Lys in KRT2 occurred at birth. Erythroderma was observed in 11.1% of the cases with p.Glu487Lys in KRT2.     

Thermal cis–trans conversion in thiophene oligomers

Thermal cis–trans conversion has been examined in oligothiophene single molecules encapsulated in the molecular vessels of cyclodextrin and Na-mordenite. At high temperatures, optical absorption intensities are enhanced in bithiophene, terthiophene and quinquethiophene, while the intensity of quarterthiophene is temperature independent. Optical absorption comes from uncompensated transition dipole moment due to the thermal torsion between cis and trans forms.     

Effects of Sampling Tube Geometry on Soft Clayey Sample Quality Evaluated by Nondestructive Methods

Sample disturbance caused by difference in sampling tube geometry was evaluated by two nondestructive methods: the measurement of the residual effective stress (p_r') by ceramic disc; and the use of the bender element to ascertain the shear wave velocity (V_s), and thus the maximum shear modulus (G_BE). Samples were measured under atmosphere, i.e., not under confined stress conditions. The soil samples were obtained from two sources: reconstituted Kasaoka clay prepared in the laboratory, and at the test site at Takuhoku, Hokkaido, Japan. Samplers with different geometrical designs, referring to the Japanese standard stationary piston sampler, were used for the model ground and field sampling. The geometrical effects of the sampling tube, for example, the thickness of the tube wall, the edge angle, and the existence of a piston were carefully examined. The quality of the samples taken with different samplers was evaluated by p_r' and G_BE, values which were normalized by the in situ vertical effective stress (σ'_vo) and G_f measured by the seismic cone test in the field. It was found from these studies that p_r'/σ'_vo and G_BE/G_f vary considerably due to the geometry of the sampler, with the edge angle of sampling tubes being the most important feature in obtaining high quality samples. The wall thickness, and thus, the area ratio of the sampler is not critical to the sample quality if the edge angle is sharp enough. The existence of the piston does not significantly influence the sample quality in field samples. Furthermore, the correlation between G_BE and p_r' was also investigated, and it was found that the two parameters are strongly dependent.     

On-line control of feed-speed in circular sawing

An adaptive control optimization system was developed to produce a desired surface finish roughness by automatic control of the work-piece feed-rate in circular sawing. The system developed in this study consists of the interconnection of an adaptive controller with a numerically controlled circular saw. The AE signals and cutting forces were measured to monitor the machining process continuously in this system. The signals were provided to the adaptive controller to evaluate the surface finish roughness and adjust the workpiece feed-rate automatically in the machining process. Sensing of AE signals and of cutting forces was compared to determine which technique is more convenient. Experiments were carried out with a carbide-tipped circular saw. Cross cutting was done with counter-cutting during the experiments. The cutting parameters controlled were workpiece feed-rates and cutting speeds. Japanese beech (Fagus crenata Blume) and Yezo spruce (Picea jezoensis Carr.) were used as the workpiece. Experimental results indicated that adaptive control optimization took place in the system developed for circular sawing. The desired surface finish roughness was produced by automatic control of the workpiece feed-rate using the sensing technique of AE signals as well as that of cutting force. However, the system using AE signals is more convenient than taht using cutting force.     

Electron holographic 3-D nano-analysis of Au/TiO2 catalyst at interface

Three-dimensional (3-D) nanostructures of gold catalysts supported on TiO2 were analysed by electron holography and high-resolution electron microscopy. The contact angle of the gold particle on TiO2 tended to be >90 degrees in the case of gold particles with a size (height) of >4 nm and it tended to be <90 degrees for gold particles with a height of <2 nm. The change in morphology increases the perimeter at the Au/TiO2 interface as the particle size decreases. This change in 3-D structure should be attributed to a change in electronic structure at the interface. It was found that electron holography enabled 3-D analysis at the atomic level and was effective for analysing nanostructured particles.     

Scaling theory for double-gate SOI MOSFET's

A scaling theory for double-gate SOI MOSFETs, which gives guidance for device design (silicon thickness t_si; gate oxide thickness t_ox) that maintains a subthreshold factor for a given gate length is discussed. According to the theory, a device can be designed with a gate length of less than 0.1 μm while maintaining the ideal subthreshold factor. This is verified numerically with a two-dimensional device simulator     

Tensile strained QW structure for low-threshold operation of short-wavelength, AlGaInP LDs emitting in the 630 nm band

The amount of tensile strain introduced into QWs and the optimum QW structure are evaluated for low-threshold operation of AlGaInP LDs in the wavelength range 630-640 nm. Very low threshold current of 32 mA under CW operation at 20 degrees C is achieved in an index-guided SQW LD emitting at 632 nm.<>