Growth and led evaluation ofN-type conductive lec gaas co-doped with in and si

Dislocation-free and low dislocation densityn-type conductive GaAs crystals, 50 mm in diameter, were grown by the In and Si co-doping LEC technique. Two-dimensional LED arrays were fabricated on substrates obtained from these crystals by the MOCVD technique and the influence of the In doping on the LED characteristics was examined. The light output power of LEDs fabricated on co-doped substrate with an In concentration of 1 ×10²⁰atoms/cm³ are low and are non-uniformly distributed, as compared with the boat-grown substrate, even though the co-doped substrate is dislocation-free. However, the LED properties of a substrate with an In concentration of 2 × 10¹⁸atoms/cm³ are the same as those of a boat-grown substrate. The light output power of the LEDs becomes higher as the In concentration in the substrate decreased.     

Lightning occurrence data observed with lightning location systems of electric power companies in Japan: 2009–2013

Nine electric power companies in Japan have been collecting lightning data with lightning location systems. Five years of the lightning data (2009–2013) are summarized and analyzed in this paper. The recent annual number of lightning flashes of which the current is more than 10 kA in Japan is around 1 million. The variations of lightning occurrence characteristics by areas, seasons, and so on, are clarified. Meteorological conditions that may affect lightning occurrence are also discussed. Furthermore, we show that there is a clear correlation between the number of lightning strikes and the outage rate of transmission lines. © 2016 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Structural Analysis of the Complex between Penta-EF-Hand ALG-2 Protein and Sec31A Peptide Reveals a Novel Target Recognition Mechanism of ALG-2

ALG-2, a 22-kDa penta-EF-hand protein, is involved in cell death, signal transduction, membrane trafficking, etc., by interacting with various proteins in mammalian cells in a Ca²⁺-dependent manner. Most known ALG-2-interacting proteins contain proline-rich regions in which either PPYPXnYP (type 1 motif) or PXPGF (type 2 motif) is commonly found. Previous X-ray crystal structural analysis of the complex between ALG-2 and an ALIX peptide revealed that the peptide binds to the two hydrophobic pockets. In the present study, we resolved the crystal structure of the complex between ALG-2 and a peptide of Sec31A (outer shell component of coat complex II, COPII; containing the type 2 motif) and found that the peptide binds to the third hydrophobic pocket (Pocket 3). While amino acid substitution of Phe⁸⁵, a Pocket 3 residue, with Ala abrogated the interaction with Sec31A, it did not affect the interaction with ALIX. On the other hand, amino acid substitution of Tyr¹⁸⁰, a Pocket 1 residue, with Ala caused loss of binding to ALIX, but maintained binding to Sec31A. We conclude that ALG-2 recognizes two types of motifs at different hydrophobic surfaces. Furthermore, based on the results of serial mutational analysis of the ALG-2-binding sites in Sec31A, the type 2 motif was newly defined.     

Evaluation of MPN method combined with PCR procedure for detection and enumeration of Vibrio parahaemolyticus in seafood

Vibrio parahaemolyticus densities in spiked and naturally contaminated seafood samples were enumerated by the MPN method combined with a PCR procedure (MPN-PCR method) targeting the species-specific thermolabile hemolysin gene (tlh), and by the MPN method using subcultivation of alkaline-peptone-water (APW) enrichment culture on thiosulfate-citrate-bile-sucrose (TCBS) agar (MPN-TCBS method). In the samples spiked with both V. parahaemolyticus and V. alginolyticus, the numbers of V. parahaemolyticus enumerated by the MPN-PCR method were similar to, or higher than the numbers of spiked cells, whereas those enumerated by the MPN-TCBS method were below the numbers of spiked cells. In naturally contaminated seafood samples, the numbers of V. parahaemolyticus enumerated by the MPN-PCR method were higher than those by the MPN-TCBS method. In the case of the MPN-TCBS method, isolation of V. parahaemolyticus from some APW cultures was difficult because of the overgrowth of many colonies other than V. parahaemolyticus (e.g., V. alginolyticus) on TCBS agar. In contrast, the PCR technique could detect tlh from APW culture without isolation of V. parahaemolyticus, so the possibility of failing to obtain a positive result in APW culture by the MPN-PCR method was considered to be lower than that by the MPN-TCBS method. Furthermore, utilization of the PCR technique reduces the time and labor required for the biochemical identification tests used in the MPN-TCBS method. For the detection and enumeration of V. parahaemolyticus in seafood, especially for samples that show many colonies other than V. parahaemolyticus on TCBS agar, the MPN-PCR method may be more convenient and reliable than the MPN-TCBS method.     

Numerical computation on the control of aerial flow by the magnetizing force in gravitational and nongravitational fields

Two-dimensional numerical computations were carried out in order to examine the effect of magnetizing force for the air in a cylindrical container with thermal and magnetic field gradients. In a gravitational field, the air was driven by both gravitational and magnetizing forces, and flow pattern and the heat transfer rate greatly depended on the axial position of the coil. Moreover, when the magnetizing and gravitational forces cancel out each other, convection became almost quiescent. On the other hand, the aerial flow was induced by the magnetizing force even in a nongravitational field, and the air behaved like an electrically conducting fluid.     

A circulating current control scheme for multiple three‐level NPC inverter systems

In recent years, motor drive systems for steel rolling mills have been steadily increasing in capacity. In particular, the development of three‐level NPC (Neutral Point Clamped) inverters is now focusing on the replacement of cycloconverters. In order to satisfy such a requirement, in this paper a multiple three‐level NPC inverter system is proposed. The configuration consists of two three‐level NPC inverters with the same configuration connected in parallel by current limiting reactors. In this case, the circulating current flowing between the two three‐level NPC inverters must be controlled to prevent a decrease in the maximum output capacity. In particular, a new method for control of the circulating current is a major topic of discussion. The method is based on space voltage vector‐based PWM (Pulse Width Modulation) control for the three‐level NPC inverters and the circulating current is controlled by adjusting the output durations of the respective space voltage vectors. In this method the circulating current controller can be decoupled from the motor current controller. Therefore, it is possible to design the different controllers independently. In addition, the experimental results obtained using an induction motor show that the circulating current can be reduced to within 2% of the rated motor current when the motor current response exceeds 1000 rad/s. © 2001 Scripta Technica, Electr Eng Jpn, 136(2): 38–48, 2001     

Decreasing the initial irreversible capacity loss of graphite negative electrode by alkali-addition

The effect of alkali function group contained in electrode binder was investigated. Carboxy methyl cellulose (CMC) improved the initial irreversible capacity loss in graphite negative electrode. Lithium acetate also improved the initial cycle efficiency. On the other hand, ethyl cellulose (EC) and hydroxyl propyl methyl cellulose (HPMC), which do not have a carboxylic group, did not decrease the reductive electrolyte decomposition. After charge and discharge cycle, the surface film composition on the electrode with CMC was less than on the electrode without CMC. This suggests that a carboxylic group in the binder acted as a catalyst and promoted the solid electrolyte interphase (SEI) formation which prevents the excess electrolyte decomposition on the graphite electrode.     

NO–H2–CO–O2 Reactions Over Pt Catalysts Supported on Ln-incorporated FSM-16 (Ln = La, Ce and Pr)

Catalytic NO–H₂–CO–O₂ reaction was studied over Pt-supported Ln-incorporated FSM-16 (Ln = La, Ce and Pr). Pr-FSM-16 exhibited the highest activity for NO _x reduction at ≤200 °C. Pr has an effect of increasing the basicity to promote the oxidative adsorption of NO, which is a key for efficient de-NO _x .     

Oxygen Potential Analysis to Evaluate Irradiation Behavior in MOX and MA-Bearing MOX Fuels

Oxygen potentials of oxide nuclear fuels are important thermodynamic data in development of nuclear fuel technologies. Minor actinide bearing MOX （mixed oxide） fuels have been developed as sodium cooled fast reactor fuels. Content of Am which is one of the minor actinide elements causes oxygen potentialto increase. The effects of the oxygen potential increase on the irradiation behavior were evaluated. Profiles of temperature and O/M （oxygen-to-metal） ratio in the pellets were evaluated to better understand the irradiation behavior. From these data, local oxygen potential in the radial direction of the pellets was calculated, and was compared with free energy of compounds composed of fission products. Based on this comparison, it was concluded that Cs2MoO4 was likely formed at pellet periphery of （U07Pu03）O1.98 and （U0.66Pu03Amoo16Npo.016）Ol.976 The extent of cladding tube inner surface oxidation was predicted by using the calculated oxygen potential. No significant difference between irradiation behaviors of （Uo.7Puo3）O2_x and （U0.66PUo 3Amo.016Npo.016）O2.x pellets was confirmed.     

Synthesis of BaAl2S4:Eu2+ Electroluminescent Material by the Polymerizable Complex Method Combined with CS2 Sulfurization

Eu-activated BaAl₂S₄ (BaAl₂S₄:Eu) blue light emission phosphor has attracted considerable attention recently as a prospective material for full color electroluminescent display applications. Although BaAl₂S₄:Eu was discovered over 30 years ago, the solid-state reaction between metal sulfides in sealed quartz ampoules remains the main method for the synthesis of this material. In this work, a homogeneous single-phase Ba_0.95Eu_0.05Al₂S₄ (BaAl₂S₄:Eu) phosphor was obtained by the sulfurization–reduction of the multicomponent oxide precursor in a CS₂ atmosphere at 1050°C. The oxide precursor containing barium, aluminum, and europium for this process was prepared by the polymerizable complex method, which ensures a high degree of homogeneity in the final product. The BaAl₂S₄:Eu material thus obtained exhibited a single emission line at 475 nm and a fluorescence intensity of 35% compared with one of the best commercially available (Ba,Eu)MgAl₁₀O₁₇ phosphors.