Pipe Heating System with Underground Water Tank for Snow Thawing and Ice Prevention on Roads and Bridge Decks

In order to prevent traffic accidents on snow-covered bridge decks, the writers developed a new pipe heating system that uses only groundwater stored in a large underground tank. The underground tank provides geothermal energy, i.e., groundwater of constant temperature, through heating pipes embedded in concrete pavements with no electric heater or fuel boiler. The pipe heating system was constructed at approximately 50% of the cost of comparable systems. In addition, there is a reduction of 10% in operating costs compared with the previous system. The present paper outlines its design and construction and provides fundamental data for the developed system. The piped heating system has kept the road conditions safe during the winter season by always removing the snow and ice from the heated road and bridge sections earlier than the surrounding roads. According to long-term temperature measurements, this system has prevented the road temperature from decreasing below 0°C, even through nighttime and morning periods. This report presents the system as an economical and effective solution for snow thawing and ice prevention.     

New technique for bonding hydroxyapatite ceramics and magnesium alloy by hydrothermal hot-pressing method

The solidification of hydroxyapatite (HA:Ca₁₀(PO₄)₆(OH)₂) and its bonding with Magnesium (Mg) alloys (AZ31; Mg–3Al–1Zn) were achieved simultaneously by using a hydrothermal hot-pressing method at a low temperature as low as 150 °C with no special surface treatment of Mg alloy. A mixture of calcium hydrogen phosphate dihydrate and calcium hydroxide was used as a starting powder material for solidifying HA. 3-point bending tests were conducted to obtain an estimate of the fracture toughness for the HA/Mg interface as well as for the HA ceramics only. The fracture toughness tests showed that the induced crack from the pre-crack tip deviated from the HA/Mg interface and propagated into the HA. The fracture toughness determined on the bonded HA/Mg specimen was close to that of the HA ceramics only (0.30 MPam^1/2).     

TWO-CRACK PROPAGATION PATHS IN A FUNCTIONALLY GRADED MATERIAL PLATE SUBJECTED TO THERMAL LOADINGS

Two-crack propagation paths in a ceramic/metal functionally graded material plate (FGP) under one-cycle temperature change of heating and cooling are considered. When the FGP is subjected to thermal shock, a single crack or multiple cracks often initiate on the ceramic surface during the cooling process and propagate in the FGP. Crack paths are influenced by the heating temperature conditions, a compositional profile of the FGP, the fracture toughness, interaction among multiple cracks, and so on. Transient thermal stresses are treated as a linear quasi-static thermoelastic problem for a plane-strain state. The crack paths are treated under fracture mechanics using the finite-element method. The effects of heating temperature conditions, a compositional profile of the FGP, the fracture toughness, and a crack space on the crack propagation pattern are discussed and are shown in figures.     

各种引气剂以及抑泡剂对混凝土经时变化状态等的影响

众所周知,采用粉煤灰制备混凝土,因粉煤灰成分中含有未燃炭等微粒子,容易造成阴离子型引气剂吸附在这些微粒子上,导致含气量经时损失.同时在混凝土的制备、运输过程中,因受采用的材料、拌和状态等物理因素影响,还会发生含气量经时增加的现象.所以在制备、管理混凝土时,如何保证出机初期一定的含气量、缓解含气量的经时损失或经时增加,是一项极其关键的技术.本文将就采用能改善上述状态的引气剂、抑泡剂拌和混凝土,对混凝土的经时变化以及抗冻融性等特征产生的影响进行论述.     

不同的表面处理对针织碳纤维复合材料的影响分析(英文)

纤维复合材料已经研究了数十年了。他们有着比传统材料,如钢材,优秀的多的力学性能。然而,由于相对较低的产量,梭织、编织与其3D纤维结构的复合材料被认为较难大量生产。因此,近年来,针织物在复合材料界获得了较高的关注,它的高度可塑性使针织复合材料可以直接生产制造成各种复杂形状的复合材料如管状、圆锥型等,使得材料的浪费可以降到了最低。本文使用了有表面处理和没有表面处理的纬编平针碳纤维制成复合材料。对两种复合材料的经向和纬向分别做了拉伸试验。结果显示:有表面处理的材料具有更好的拉伸性能,尤其是在wale方向上,有表面处理的复合材料比没有表面处理的复合材料的拉伸强度提高75.68%。     

Study of all-optical clock recovery performance by the primary and the secondary temporal Talbot effects in a second-order dispersive medium

We theoretically and experimentally study the all-optical clock recovery performance using the primary or the secondary temporal Talbot effects (PTTE or STTE, respectively) in a dispersive medium having the first-order dispersion together with the second-order dispersion (e.g., conventional single-mode fibers: SMFs). Our preliminary numerical simulations have indicated that the STTE-based all-optical clock recovery technique can improve double its performance as compared with the conventional PTTE-based technique when the second-order dispersion (dispersion slope) can be neglected. The following simulation results have revealed that the second-order dispersion, that the normal SMFs possess, limits the performance improvements in the STTE-based clock recovery, whereas the limited performance can be improved by appropriately compensating for the second-order dispersion. On the basis of our simulation results, experiments of the STTE-based clock recovery were conducted by compensating for the second-order dispersion of SMFs used as dispersive media. To be specific, SMFs’ second-order dispersion has been reduced to the one-sixteenth of its original value by combining with the reverse-dispersion fibers (RDFs) which can provide the second-order dispersion of the opposite sign to the SMFs. As a result, the performance improvements in the STTE-based clock recovery was demonstrated so that the 10-GHz clear optical clock pulses were successfully recovered from 10-Gbit/s return-to-zero (RZ) pseudo-random bit sequence (PRBS) optical signals.     

Characterization of microstructural damage due to low-cycle fatigue by EBSD observation

Electron backscatter diffraction (EBSD) in conjunction with scanning electron microscopy was used to assess the damage due to cyclic or uniform strain. Samples of Type 316 stainless steel after fatigue and tensile tests were prepared for EBSD observation and the misorientation angle between neighboring points (local misorientation) was evaluated. It was shown that the local misorientation developed due to the cyclic and uniform strain and that its spatial distribution was not uniform. In fatigue samples, the area of large local misorientation tended to form clusters, whereas it localized to the grain boundaries in the tensile samples, and the magnitude of local misorientation and the degree of the localization increased with the strain amplitude. The degree of localization was quantified via statistical processing of the measured data. It was also shown that the source of damage (cyclic or uniform strain) and the loading direction could be deduced from the EBSD observations of the damaged sample.     

Preliminary spectrum shifter design for intermediate energy nuclear data benchmark experiments with DT neutrons

Integral benchmark experiments with DT neutrons are not always sufficient for nuclear data benchmarking in the MeV region, below 10 MeV. A neutron spectrum shifter, which will be placed between a sample and a DT neutron source, is effective to moderate DT neutrons incident to the sample. In order to estimate effects of the spectrum shifter, the ratio of the contribution of 14 MeV neutrons in the leakage neutron and gamma-ray spectra was calculated with MCNP-4C for an experimental configuration at FNS of JAEA, Japan. The calculations were carried out for a Li₂TiO₃ sample with a Be, D₂O, or ⁷LiD spectrum shifter. It was found out that the Be shifter was superior to others and the Be shifter was effective to decrease the contribution of 14 MeV neutrons especially for secondary gamma-ray spectrum measurements.