Buoyant heat transport in fluids across tilted square cavities discretely heated at one side

Laminar natural convection heat transfer inside fluid-filled, tilted square cavities cooled at one side and partially heated at the opposite side, is studied numerically. A computational code based on the SIMPLE-C algorithm is used for the solution of the system of mass, momentum, and energy transfer equations. Simulations are performed for a complete range of heater sizes and locations, Rayleigh numbers based on the side of the cavity from 10³ to 10⁷, Prandtl numbers from 0.7 to 700, and tilting angles of the enclosure from ?75° to +75°, where negative angles correspond to configurations with the heater facing downwards. It is found that the heat transfer rate increases with increasing the Rayleigh and Prandtl numbers, and the size of the heater. In addition, for negative inclinations of the enclosure the amount of heat exchanged decreases with increasing the tilting angle, while for positive inclinations the heat transfer rate either increases or decreases according as the heater is located toward the top or the bottom of the cavity. Finally, as far as the heater location is specifically concerned, the heat transfer performance has a peak for intermediate positions, the higher are the Rayleigh and Prandtl numbers, as well as the tilting angle for positive inclinations, the closer to the bottom of the cavity is the optimum heater location for maximum heat removal.     

Low computational cost CFD analysis of thermoacoustic oscillations

The numerical analysis of thermoacoustic oscillation phenomena by means of time-dependent CFD simulations usually requires a great computational effort, which may not be reasonable in industrial design. On the other hand, CFD tools provide the only approach that includes all the physical and chemical aspects involved in the thermoacoustic coupling between flame heat release and the acoustic modes of the burner/combustion chamber system. This paper presents some guidelines to reduce the computational effort required to perform a CFD analysis of the thermoacoustic oscillations with commercial codes. These guidelines are organized in a procedure that can be followed to analyze thermoacoustic coupling conditions that actually lead to unstable oscillations or are identified as potentially critical in the design phase. This procedure is also illustrated by an example of application, the partially-premixed flame type burner of a real 10 MW industrial boiler which shows noisy pressure fluctuations at a low frequency.     

Correlating equations for free convection heat transfer from horizontal isothermal cylinders set in a vertical array

Steady laminar free convection from flat vertical arrays of equally-spaced, horizontal isothermal cylinders set in free air, is studied numerically. A specifically developed computer-code based on the SIMPLE-C algorithm is used for the solution of the mass, momentum and energy transfer governing equations. Simulations are performed for arrays of 2-6 circular cylinders, for center-to-center separation distances from 2 up to more than 50 cylinder-diameters, and for values of the Rayleigh number based on the cylinder-diameter in the range between 5 × 10² and 5 × 10⁵. It is found that the heat transfer rate at the bottom cylinder remains the same as a single cylinder. In contrast, the downstream cylinders may exhibit either enhanced or reduced Nusselt numbers depending on their location in the array and on the geometry of the array. Heat transfer dimensionless correlating equations are proposed both for any individual cylinder in the array and for the whole tube-array. New correlation-equations for the calculation of the heat transfer rate from a single cylinder to the surrounding air are also proposed and compared to those available in the open literature.     

Open-loop groundwater heat pumps development for large buildings: A case study

A study of the feasibility of providing the heating and cooling needs of the new, large commercial building near Turin, Italy, by means of an open-loop indirect groundwater heat pump (GWHP) system is described. A finite element subsurface flow and transport simulator (FEFLOW) was used to investigate possible configurations of extraction and injection wells for five different scenarios. Modelling results confirmed the hydrogeological capacity of the site to provide the necessary amount of groundwater and associated energy with limited environmental impact. Injection of warmer (or cooler) water in the aquifer creates a thermal plume whose dimensions and geometry depend on the properties of the subsurface formations, particularly their thermal dispersivity values. The study suggests that there are several possible well configurations that could support the GWHP system without adversely affecting the aquifer.     

Initial pH influences microbial communities composition in dark fermentation of scotta permeate

This study addresses for the first time the influence of initial pH on the evolution of microbial consortia in dark fermentation of scotta permeate, using a high-throughput sequencing approach. Three fermentation phases could be detected: 1) a lag phase with no substantial differences in microbial composition at different initial pH values; 2) an exponential H₂ production phase, accompanied by a general increase of Clostridium genus components and higher incidence of Trichococcus genus at neutral and alkaline pH; 3) a final stationary phase, characterized by a general increase of Bifidobacterium and Lactobacillus genera in all reactors. The initial pH value influenced the relative abundance of Trichococcus at 16–48 h of incubation. The metabolic activity of this genus increased the amount of metabolic precursors of H₂ so that, when pH lowered to 5.4, clostridia in the reactors with initial alkaline pH become more active H₂-producers than those in the others.     

Property specification patterns at work: verification and inconsistency explanation

Innovations in Systems and Software Engineering - Property specification patterns (PSPs) have been proposed to ease the formalization of requirements, yet enable automated verification thereof. In...     

Comments on the article ‘Comparison of calculations for interplanar distances in a crystal lattice’, by Ying Liu,Yue Liu & Michael G. B. Drew

Some statements in the review by Liu et al. [Liu Y, Liu Y, Drew GB. Comparison of calculations for interplanar distances in a crystal lattice. Cryst Rev. 2017] are corrected. The role of metric tensor to simplify calculations of interplanar spacings in crystal lattices is emphasized.     

Development of an experimental test rig for cogeneration based on a Stirling engine and a biofuel burner

A system consisting of a last-generation Stirling engine (SE) and a fuel burner for distributed power generation has been developed and experimentally investigated. The heat generated by the combustion of two liquid fuels, a standard Diesel fuel and a rapeseed oil, is used as a heat source for the SE, that converts part of the thermal energy into mechanical and then electric energy. The hot head of the SE is kept in direct contact with the flame generated by the burner. The burner operating parameters, designed for Diesel fuel, were changed to make it possible to burn vegetable oils, not suitable for internal combustion engines. The possibility of adopting different configurations of the combustion chamber was taken into account to increase the system efficiency. The preliminary configurations adopted allowed to operate this integrated system, obtaining an electric power up to 4.4 kW_el with a net efficiency of 11.6%.