Source reconciliation of atmospheric gas-phase and particle-phase pollutants during a severe photochemical smog episode

A comprehensive organic compound-based receptor model is developed that can simultaneously apportion the source contributions to atmospheric gas-phase organic compounds, semivolatile organic compounds, fine particle organic compounds, and fine particle mass. The model is applied to ambient data collected at four sites in the south coast region of California during a severe summertime photochemical smog episode, where the model determines the direct primary contributions to atmospheric pollutants from 11 distinct air pollution source types. The 11 sources included in the model are gasoline-powered motor vehicle exhaust, diesel engine exhaust, whole gasoline vapors, gasoline headspace vapors, organic solvent vapors, whole diesel fuel, paved road dust, tire wear debris, meat cooking exhaust, natural gas leakage, and vegetative detritus. Gasoline engine exhaust plus whole gasoline vapors are the predominant sources of volatile organic gases, while gasoline and diesel engine exhaust plus diesel fuel vapors dominate the emissions of semivolatile organic compounds from these sources during the episode studied at all four air monitoring sites. The atmospheric fine particle organic compound mass was composed of noticeable contributions from gasoline-powered motor vehicle exhaust, diesel engine exhaust, meat cooking, and paved road dust with smaller but quantifiable contributions from vegetative detritus and tire wear debris. In addition, secondary organic aerosol, which is formed from the low-vapor pressure products of gas-phase chemical reactions, is found to be a major source of fine particle organic compound mass under the severe photochemical smog conditions studied here. The concentrations of secondary organic aerosol calculated in the present study are compared with previous fine particle source apportionment results for less intense photochemical smog conditions. It is shown that estimated secondary organic aerosol concentrations correlate fairly well with the concentrations of 1,2-benzenedicarboxylic acid in the atmospheric fine particle mass, indicating that aromatic diacids may be useful in the quantification of certain sources of secondary organic aerosol in the atmosphere.     

Advanced mercury removal from gold leachate solutions prior to gold and silver extraction: a field study from an active gold mine in Peru

Mercury contamination in the Gold-Cyanide Process (GCP) is a serious health and environmental problem. Following the heap leaching of gold and silver ores with NaCN solutions, portions of the mercury-cyano complexes often adhere to the activated carbon (AC) used to extract the gold. During the electrowinning and retorting steps, mercury can be (and often is) emitted to the air as a vapor. This poses a severe health hazard to plant workers and the local environment. Additional concerns relate to the safety of workers when handling the mercury-laden AC. Currently, mercury treatment from the heap leach solution is nonexistent. This is due to the fact that chelating ligands which can effectively work under the adverse pH conditions (as present in the heap leachate solutions) do not exist. In an effort to economically and effectively treat the leachate solution prior to passing over the AC, a dipotassium salt of 1,3-benzenediamidoethanethiol (BDET2-) has been developed to irreversibly bind and precipitate the mercury. The ligand has proven to be highly effective by selectively reducing mercury levels from average initial concentrations of 34.5 ppm (parts per million) to 0.014 ppm within 10 min and to 0.008 ppm within 15 min. X-ray powder diffraction (XRD), proton nuclear magnetic resonance (1H NMR), Raman, and infrared (IR) spectroscopy demonstrate the formation of a mercury-ligand compound, which remains insoluble over pH ranges of 0.0-14.0. Leachate samples from an active gold mine in Peru have been analyzed using cold vapor atomic fluorescence (CVAF) and inductively coupled plasma optical emission spectroscopy (ICP-OES) for metal concentrations before and after treatment with the BDET2- ligand.     

Discrimination of aerial deposition sources of polychlorinated dibenzo-p-dioxin and polychlorinated dibenzofuran downwind from a pulp mill near Ketchikan, Alaska

Drinking water is supplied by individual roof-catchment systems for homes and businesses near a dissolving sulfite pulp mill (now closed) located just north of Ketchikan in southeast Alaska. This study was conducted to determine if polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/Fs) found in the sediments of the roof-catchment cisterns resulted from historical deposition of stack emissions from the pulp mill's multi-fuel power boilers. Fly ash from the power boilers had maximum total PCDD/F concentrations of 3.08 x 10(5)-3.10 x 10(6) ng/kg, which resulted from combustion of bleach plant wastewater sludge and saltwater-soaked wood waste. Cistern sediments had maximum total PCDD/F concentrations of 7.71 x 10(4) ng/kg. Potential sources of PCDDs/Fs in the cistern sediments were considered to be automobile exhaust, heating oil combustion, and private trash burning as well as pulp mill boiler emissions. Discriminant analysis was used to analyze differences between profiles of tetra through octa homologue classes of PCDDs/ Fs (defined as proportional contributions to total concentration) from different source terms. Homologue profiles of potential sources from Ketchikan included in this analysis were fly ash collected from the mill's power boilers and soils collected from background areas (areas with similar PCDD/F sources as the residences [e.g., auto exhaust and burn barrels] near the mill but beyond the zone of aerial deposition of emissions from the mill). Profiles for emissions from automobile exhaust, fertilizers, oil heating, residential trash burning, and residential wood heating were also included in the source "training" data set (for the discriminant analysis) using data from published literature. The classification rules developed from the discriminant analysis were applied to the following test media sampled at Ketchikan: roof-catchment cistern sediments and soils collected from areas in the vicinity of the mill's power boilers (i.e., nearby residential or commercial [developed] areas, on the mill property, and nearby forestlands). The homologue profiles of cistern sediment and nearby developed area soil samples were similar to background soils, whereas the profiles for the forestland soil samples (influenced by emissions from the mill but not other anthropogenic sources) closely matched the fly ash pattern. The homologue profiles of the emission sources from published data were more similar to one another than either background soils or fly ash. Soil samples from the mill property were classified as members of all source groups. On the basis of these analyses, the composition of PCDDs/Fs detected in the cistern sediments is typical of Ketchikan background conditions and not reflective of mill emissions.     

Development and evaluation of an on-line hide decontamination procedure for use in a commercial beef processing plantt

The hides of cattle are the source of Escherichia coli O157:H7 that contaminates beef carcasses during commercial beef processing. Therefore, effective interventions that reduce hide contamination should reduce subsequent carcass contamination. The first objective of this study was to identify the most effective reagents for decontamination of beef hides. Cattle hides draped over barrels were used for in vitro experiments to compare the efficacy of washes using 1.6% sodium hydroxide, 4% trisodium phosphate, 4% chlorofoam, or 4% phosphoric acid, each followed by a rinse step using either water or acidified (pH 7.0) chlorine at 200 or 500 ppm. All treatments using a water rinse reduced hide coliform counts by 1.5 to 2.5 log CFU/ 100 cm2. Compared with water rinses, 200 and 500 ppm acidified chlorine rinses increased efficacy by approximately 1.0 and 2.0 log CFU/100 cm2, respectively. Vacuuming of the treated areas to remove excess liquid improved hide cleanliness by an average of an additional 1.0 log CFU/100 cm2. The second objective was to evaluate the use of an on-line hide-wash cabinet that used a sodium hydroxide wash and a chlorinated (1 ppm) water rinse. Hides sampled before entering and after exiting the cabinet had aerobic plate counts and Enterobacteriaceae counts that were reduced by 2.1 and 3.4 log CFU/100 cm2, respectively, and the prevalence of E. coli O157 on hides was reduced from 44 to 17% when the cabinet was in use. Preevisceration carcass aerobic plate counts and Enterobacteriaceae counts were both reduced by 0.8 log CFU/100 cm2, and the prevalence of E. coli O157 on preevisceration carcasses was reduced from 17 to 2% when the cabinet was in use. These results support decontamination of hides as an effective means to reduce pathogen contamination of cattle carcasses during processing.     

Comprehensive Review of Patulin Control Methods in Foods

The mycotoxin, patulin (4‐hydroxy‐4H‐furo [3, 2c] pyran‐2[6H]‐one), is produced by a number of fungi common to fruit‐ and vegetable‐based products, most notably apples. Despite patulin's original discovery as an antibiotic, it has come under heavy scrutiny for its potential negative health effects. Studies investigating these health effects have proved inconclusive, but there is little doubt as to the potential danger inherent in the contamination of food products by patulin. The danger posed by patulin necessitates its control and removal from foods products, creating a demand for handling and processing techniques capable of doing so, preferably at low cost to industry. With this being the case, much research has been devoted to understanding the basic chemical and biological nature of patulin, as well as its interaction within foods and food production. While past resarch has elucidated a great deal, patulin contamination continues to be a challenge for athe food industry. Here, we review in depth the past research on patulin with an emphasis upon its influence within the food industry, including its regulation, health effects, biosynthesis, detection, quantification, distribution within foods, and control, during the various stages of apple juice production. Finally, key areas where future patulin research should focus to best control the patulin contamination problem within the food industry are addressed.     

Comparison of Methods for Colorimetric Amylose Determination in Cereal Grains

Iodine‐based colorimetry remains the most widespread method for the determination of amylose content of starch. There are, however, many variants of this method, differing in solvent, temperature and method for converting absorbance to amylose content. Therefore, in thisstudy some of these methods were compared in order to identify which, if any, was most reliable. Australian commercial samples of wheat, rice, rye and oat were used. Flour was ground and starch was extracted. Half of the samples of flour and starch were defatted with n‐propanol. Defatted and full‐fat flours and starches were dissolved by six procedures: DMSO, urea‐DMSO, CaCl₂‐DMSO, hot NaOH, cold NaOH and HCl. The solutions were diluted, coloured with iodine and the absorbances determined at 535 and 620 nm. Amylose content was determined by reference to standards using 620 nm as the single wavelength or by two calculations based on the ratio between the two absorbances. Reliability was tested by repeating all tests on three non‐consecutive days with three replicates on each day. Defatted starch provided more consistent results than flour or non‐defatted starch. The most reliable dissolution procedure, with both the lowest standard error and least day‐to‐day variation, was cold NaOH. One of the ratio‐based calculations provided adequate correction for the non‐starch content of flour of wheat and rice, but not of the other two cereals, and the other ratio‐based calculation seldom provided realistic results. It is concluded that a cold NaOH dissolution procedure is suitable for reliable amylose determination on defatted starch of a range of cereals from a single wavelength and that it is also suitable for use on defatted flour of some species.