Functionalization of Polymer Surfaces Using Excimer VUV Systems and Silent Discharges. Application to Electroless Metallization

New approaches for electroless plating of nonconductive polymers or polymer-based materials are described. In this work, polyimide substrates were surface-functionalized (i) in nitrogenated (ammonia at reduced pressure) and oxygenated (air at atmospheric pressure) atmospheres under assistance of vacuum-ultraviolet (VUV) irradiation (use of a xenon silent discharge excimer source) or (ii) directly in air at atmospheric pressure using a dielectric-barrier discharge (DBD) device. After functionalization, the substrates were “activated” by dipping in a dilute acidic PdCl₂ solution or by spin-coating of a thin metal-organic film (from a solution of palladium acetate (PdAc) in chloroform). The catalytic activity of the so-deposited palladium species toward the electroless deposition of nickel was studied before and after a VUV post-irradiation (in air at atmospheric or reduced pressure) with a view to understanding better the role of the reducer (sodium hypophosphite) within the electroless bath.

This work confirms the specific interest of grafting nitrogenated functionalities onto polymer surfaces for attaching covalently the palladium-based catalyst (in particular in the case of the PdCl₂ route), forming thus strong Pd - N - C bonds at the metal/polymer interface. This results from the strong chemical affinity of palladium toward nitrogen. On the other hand, when oxygenated functionalities are surface-grafted, the conventional two-step procedure using SnCl₂ and PdCl₂ solutions can be proposed due to the strong chemical affinity of tin toward oxygen. The Ni deposits obtained under these different conditions pass the standard Scotch^®-tape test and, therefore, exhibit a good practical adhesion. For this same purpose, it is interesting to note that the DBD treatment operating in air at atmospheric pressure causes an increase of the surface roughness and, therefore, an improvement in adhesion of metallic films when their initiation is catalyzed through the PdAc route. In addition, this work demonstrates that extensive research still has to be performed to understand and improve the Ni/polymer adhesion when the PdAc route associated with a VUV irradiation is considered.     

Analysis of the Single-Crystalline Silicon Photovoltaic (PV) Module Performances Under Low γ - Radiation from Radioactive Source

The present paper is about an experimental evaluation of the terrestrial silicon single-crystalline solar PV module behavior under low gamma radiation. The     

Interaction between laser beam and BaTiO3 powders in selective laser sintering treatments

The research work reported in this paper is an investigation of the behavior of barium titanate powders under selective laser irradiation. Our goal is to determine suitable conditions to sinter the powders and form dense layers usable in some electronic components. On that purpose, compacts of micro/nano BaTiO₃ powder mixes are used for a parametric investigation of the laser scans parameters (power, speed, etc.) with a Nd-YVO₄ laser (23 W). The microstructures obtained after laser treatments are evaluated by XRD, SEM and EDS and compared to a reference specimen manufactured in a conventional way. From this work it can be concluded that a high laser beam power is required to obtain a consolidation of the powder grains and the use of a high scan speed avoids the melting. The scanning speed also influences the final crystallographic state of BaTiO₃. Optimal parameters were founded in order to form a dense and homogeneous tetragonal BaTiO₃ surface.     

Extended hydrophobicity and self-cleaning performance of waterborne PDMS/TiO<Subscript>2</Subscript> nanocomposite coatings under accelerated laboratory and outdoor exposure testing

It has been shown that incorporation of TiO₂ nanoparticles into hydrophobic coatings can show self-cleaning performance. Accelerated laboratory testing indicated that the coats retain their hydrophobic nature for an extended time period. In this paper, hydrophobic polydimethylsiloxane (PDMS)/TiO₂ nanocomposite coatings with a TiO₂ content of 0–40% were fabricated by simple blending of a PDMS dispersion with an aqueous TiO₂ nanoparticle dispersion. Their long-term hydrophobicity and self-cleaning performance were investigated both in laboratory and real-world outdoor testing. As expected, TiO₂ nanoparticle-based coatings exhibited better self-cleaning relative to the TiO₂-free PDMS control coating as measured by methylene blue degradation testing. Excellent long-term hydrophobicity was observed in accelerated weathering testing when they contained the appropriate levels of TiO₂ nanoparticles (i.e., 0–30%). However, the same PDMS/TiO₂ coatings did not show self-cleaning performance, and instead, exhibited improved dirt pickup resistance, in outdoor exposure testing. Sustained hydrophobicity was observed in outdoor exposure testing for the clear films except when TiO₂ levels were at 40%. The hysteresis of water contact angle (HWCA) significantly increased for the PDMS control coating, and water beading was lost as the film surface picked up dirt. In contrast, the TiO₂-based coatings with appropriate TiO₂ levels maintained a relatively low HWCA after outdoor exposure and no water sheeting on rainy days was observed. This result demonstrates that while photocatalytic TiO₂ nanoparticles can maintain coating hydrophobicity upon outdoor exposure, long-term self-cleaning performance in polluted environments has not yet been achieved with this type of coating under real-world conditions.     

Numerical Study of Solid-Liquid Two-Phase Flow in Stirred Tanks with Rushton Impeller (Ⅰ) Formulation and Simulation of Flow Field

Three-dimensional solid-liquid flow is mathematically formulated by means of the "two-fluid" approach and the two-phase k-ε-Ap turbulence model. The turbulent fluctuation correlations appearing in the Reynolds time averaged governing equations are fully incorporated. The solid-liquid flow field and solid concentration distribution in baffled stirred tanks with a standard Rushton impeller are numerically simulated using an improved "inner-outer" iterative procedure. The flow pattern is identified via the velocity vector plots and a recirculation loop with higher solid concentration is observed in the central vicinity beneath the impeller. Comparison of     

Effective parameters on diameter of carbon nanotubes by plasma enhanced chemical vapor deposition

The effective parameters on the diameter of carbon nanotubes (CNTs) by plasma enhanced chemical vapor deposition (PECVD) were presented.Among lots of influential parameters,the effects of the catalytic film thickness and the pretreatment plasma power on the growth of CNTs were investigated.The results show that the size of catalytic islands increases by increasing the thickness of catalytic layer,but the density of CNTs decreases.The pretreatment duration time of 30 s is the optimal condition for growing CNTs with about 50 nm in diameter.By increasing the pretreatment plasma power,the diameter of CNTs decreases gradually.However,the diameter of CNTs does not change drastically from 80 to 120 W.The uniformly grown CNTs with the diameter of 50 nm are obtained at the pretreatment plasma power of 100 W.     

空冷发电厂的热力设计与分析

本文对热力发电厂的汽轮机排汽冷却系统进行了评估。作者编制了计算机程序,并对海勒式空冷系统做了计算,结果显示了塔高、水流速与空气流量、冷却塔与散热器投资以及经济效益的关系。     

单耗分析的理论和实施

《单耗分析》是在(火用)和(火用)经济学的基础上所设计的能量系统分析的理论和方法,以产品单耗做为降耗节能的主要指标,分析单耗的构成及其分布和变化,为节能降耗技术提供实用的理论依据。     

Effects of Zirconia on Microstructure and Dielectric Properties of Barium Titanate Ceramics

Dielectric properties and structural characteristics of BaTiO₃ ceramics are significantly influenced by small addition (2 wt%) of ZrO₂. SEM and TEM observations revealed enhanced microstructural uniformity and retarded grain growth depending on sintering temperature. Above 1320°C, Zr diffusion into the BaTiO₃ lattice resulted in a chemical modification of the tetragonal structure and the development of core–shell grains. Below 1320°C, TEM analysis showed ZrO₂ at the grain boundaries as discrete particles (∼0.03μm). X-ray diffraction analysis revealed a decrease in the axial (c/a) ratio with decreasing grain size. A corresponding decrease in the spontaneous polarization, and twinned domain structures, were also observed in the fine-grained ceramics. These samples also showed a flattened permittivity response with temperature and significantly lower losses.