Enzyme‐catalyzed hydrolysis of poly(ethylene terephthalate) cyclic trimer

Oligoesters present in poly(ethylene terephthalate) fibers are commonly extracted from the fiber during processing, such as aqueous‐based dyeing. Aqueous, insoluble oligoesters, particularly cyclic trimers that precipitate on processing machinery and on the fiber surface are difficult to remove under benign conditions. Reported is a new method for the efficient removal of cyclic trimer by enzyme‐catalyzed hydrolysis. Almost complete hydrolysis of trimer was accomplished at pH 8 and 60°C. Effects of time, agitation, surfactant, and enzyme and trimer concentrations on the efficiency of hydrolysis are reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2545–2552, 2003     

High styrene–rubber ionomers,an alternative to thermoplastic elastomers

High styrene rubber ionomers were prepared by sulfonating styrene–butadiene rubber of high styrene content (high styrene rubber) in 1,2‐dichloroethane using acetyl sulfate reagent, followed by neutralization of the precursor acids using methanolic zinc acetate. The ionomers were characterized using X‐ray fluorescence spectroscopy, Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR), dynamic mechanical analysis (DMA), and also by the evaluation of mechanical properties. The FTIR studies of the ionomer reveal that the sulfonate groups are attached to the benzene ring. The NMR spectra give credence to this observation. Results of DMA show an ionic transition (T_i) in addition to glass–rubber transition (T_g). Incorporation of ionic groups results in improved mechanical properties as well as retention of properties after three cycles of processing. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2294–2300, 2002     

Rheology of oil in water emulsions with added solids

The effect of added solids on the rheology of oil in water emulsions was investigated. The range of the oil concentration, solids free basis, was (0-70%) and the solids volume fraction was (0-0.16). The solids mean diameter was 45 μm and it was about four times larger than the oil droplets. In the absence of added solids, non-Newtonian behaviour was observed for oil concentrations above 40%. The added solids increased the emulsion viscosity in a manner similar to the addition of solids to a homogeneous fluid. The rheological data of all the emulsion-solids mixtures investigated were correlated as relative viscosity versus solids volume fraction, where the relative viscosity is defined as the ratio of the emulsion-solids mixture viscosity to the solids-free emulsion viscosity. In the case of non-Newtonian systems, the emulsion-solids mixture viscosity and the solids-free emulsion viscosity were calculated at the same shear stress. The Barnea and Mizrahi viscosity correlation was found to fit the data well.     

Hydrogen and Oxygen Bubble Attachment to a Bitumen Drop

Air bubble – bitumen attachment is a critical step in the flotation of bitumen from mined oil sand. In this study, single bubble – bitumen drop attachment was observed directly using a novel experimental technique. Induction time is determined and used as an indication of bubble‐bitumen attachment potency for both hydrogen and oxygen bubbles. The attachment tests were conducted in deaerated municipal water (City of Edmonton tap water) at temperatures ranging from 22–50°C. Induction times measured for hydrogen bubble attachment were shorter than those for oxygen bubbles. Coalescence tests were also conducted in the absence of bitumen, and showed that hydrogen bubbles coalesced more rapidly than oxygen bubbles in both deaerated municipal water and clear (solids‐free) process water.     

An optimal usage of NO x in a combined Pt/ceramic foam and a wall-flow monolith filter for an effective NO x -assisted soot oxidation

Topics in Catalysis - An NO2-assisted soot oxidation based filter candidate consists of Pt-coated ceramic foam in combination with a wall-flow monolith is proposed to acquire for an optimal usage...     

Natural rubber composites reinforced with sisal/oil palm hybrid fibers: Tensile and cure characteristics

Natural rubber was reinforced with untreated sisal and oil palm fibers chopped to different fiber lengths. The influence of fiber length on the mechanical properties of the hybrid composites was determined. Increasing the fiber length resulted in a decrease in the properties. The effects of concentration on the rubber composites reinforced with sisal/oil palm hybrid fibers were studied. Increasing the concentration of fibers resulted in a reduction in the tensile strength properties and tear strength but an increase in the modulus of the composites. Fiber breakage analysis was evaluated. The vulcanization parameters, processability characteristics, and stress–strain properties of these composites were analyzed. The extent of fiber alignment and the strength of the fiber–rubber interface adhesion were analyzed from the anisotropic swelling measurements. Scanning electron microscopy studies were performed to analyze the fiber/matrix interactions. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2305–2312, 2004     

Highly potent germination inhibitors in aqueous eluate of fruits of Bishop's weed (Ammi majus L.) and avoidance of autoinhibition

The aqueous eluate from fruits ofAmmi majus (Bishop's weed, Umbelliferae) remarkably inhibited germination of adjacent seeds ofAnastatica hierochuntica, lettuce, or tomato but had no effect on intact fruits ofAmmi. Similar inhibition was found in dark or in light, except that seeds ofA. hierochuntica were significantly more inhibited in the dark than in the light. Xanthotoxin was isolated, identified, and found to account for about a sixth of the inhibitory activity of the eluate. After fruits ofAmmi were submerged in a large volume of water for 4 days, the fruits still exuded enough inhibitors to prevent germination ofA. hierochuntica, lettuce, or tomato. Data support also the proposal that the phytotoxins are compartmentalized between the inner and the outer fruit envelopes. The inner layer excludes inhibitors from the embryo and autotoxicity is thus avoided, whereas the outer one ensures a gradual liberation of the phytotoxic compounds. This, as well as the high reactivity of the eluate, the high densities ofAmmi fruits in nature, and their relatively limited annual germination, suggest chemical inhibition of neighboring plant species other thanAmmi. Hence, in addition to their chemical protection against predators of either lower or higher organisms, furanocoumarins in fruits ofAmmi majus may contribute to its success as a weed.     

Use of the Nasicon/Na2SO4 couple in a solid state sensor for SO x (x=2,3)

The e.m.f. of a concentration cell for SO _x (x=2,3)-O₂ incorporating Nasicon as the main solid electrolyte has been measured in the temperature range 720 to 1080 K. The cell arrangement can be represented as, $$Pt, O'_2 + SO'_2 + SO'_3 \left| {Na_2 SO_4 \left\| {\left. {Nasicon} \right\|} \right.} \right.\left. {Na_2 SO_4 } \right|SO''_3 + SO''_2 + O''_2 , Pt$$ The Na₂SO₄ acts both as an auxiliary electrode, converting chemical potentials of SO _x and O₂ to equivalent sodium potentials, and as an electrolyte. The presence of Na₂SO₄ provides partial protection of Nasicon from chemical reaction with gas mixtures containing SO _x . The open circuit e.m.f. of the cell is in close agreement with values given by the Nernst equation. For certain fixed inlet gas compositions of SO₂+O₂, the e.m.f. varies non-linearly with temperature. The intrinsic response time of the cell to step changes in gas composition is estimated to vary from ～2.0 ksec at 723K to ～ 0.2 ksec at 1077K. The cell functions well for large differences in partial pressures of SO₃(p″_{SO 3}/p′_{SO 3}≈10⁴) at the electrodes.     

Thermal analysis of styrene–alkyl methacrylate polymers. I. Glass transition temperatures

The glass transition temperatures (T_g's) of several polystyrenes and styrene–alkyl methacrylate copolymers and terpolymers were measured using thermomechanical analysis (TMA) and differential scanning calorimetry (DSC). The polymers studied had number-average molecular weights from 3000 to 250,000 g/mole. The results indicate that the composition dependence of the T_g's for the copolymers and terpolymers can be satisfactorily described by a general Fox equation. In general, the measured T_g's of the copolymer and terpolymer samples depend more on the steric effects of the constituent pendent groups than on their molecular weights. The chain flexibility rather than the size of the pendent group is the determining factor in the glass transition properties of the styrene polymers.