Crystallization conditions effect on molecular weight of solid-state polymerized poly(ethylene terephthalate)

Number-average molecular weight ( $ \overline{M}_{n} $ ) variation of polyethylene terephthalate with respect to crystallization temperature and time, and solid-state polymerization (SSP) time were studied using response surface experimental design method. All experiments were conducted in a fluidized bed reactor. $ \overline{M}_{n} $ values were calculated by Mark?CHouwink equation upon determining intrinsic viscosity (IV) of samples. Two suitable models were proposed for $ \overline{M}_{n} $ and IV, based on the regression coefficient. It was observed that $ \overline{M}_{n} $ increases with decrease in crystallization temperature and increase in crystallization time and SSP time. It was shown that SSP time is the most important parameter based on statistical calculations. Crystallization time, crystallization temperature and SSP time were determined 60?min, 160?°C and 8?h, respectively, in order to achieve maximum $ \overline{M}_{n} $ . Density measurements were applied to study the overall crystallinity of samples. Based on density results it was revealed that percent of crystallinity is not the only factor that affects the $ \overline{M}_{n} $ of polymer. Differential scanning calorimeter was used to analyze thermal properties of the samples. All samples showed two melting peaks. It was observed that the lower melting temperature peak is related to the isothermal crystallization process temperature. Polarized light microscopy was used to study spherulitic structures of polymer films after crystallization process. It was shown that the sample with smallest spherulite size had the maximum $ \overline{M}_{n} $ equal to 26,000?g/mol.     

Thermal degradation behavior and kinetic studies of polyacrylamide gel in TiO2 nanoparticles synthesis

Polyacrylamide gel (PAMG) method is a simple, fast and cheap method used for the synthesis of a wide variety of nanopowders. However, no adequate results have been reported on the thermal degradation behavior of PAMG which can be very effective on the final product properties. In this work, thermal degradation behavior of PAMG in the presence of TiCl₄ as a precursor salt for synthesis of TiO₂ nanoparticles was examined in comparison with linear polyacrylamide (LPAM) and pure PAMG by thermogravimetry/differential thermal analysis. Their thermal degradation kinetics was investigated, as well. The results showed that thermal degradation of all samples occurred in two stages at different onset temperatures. Despite the high thermal stability of pure PAMG compared to LPAM, the presence of TiCl₄ as a mineral material in PAMG structure decreases the thermal degradation onset temperature, considerably. Furthermore for LPAM and PAMG, majority of weight loss occurs in the second stage, but in PAMG with TiCl₄ the weight loss occurs mainly at the first stage. For more detailed investigation, residual materials were characterized by Fourier transform infrared spectroscopy and X-ray diffraction (XRD) techniques, attributing this trend to the presence of mineral materials in PAMG structure. XRD and transmission electron microscopy were also applied to confirm anatase crystalline structure and nanoscale distribution of the TiO₂ particles synthesized via PAMG method.     

A study on the properties of PMMA/silica nanocomposites prepared via RAFT polymerization

A number of batch polymerizations were performed to study the effect of pristine nanoparticle loading on the properties of PMMA/silica nanocomposites prepared via RAFT polymerization. In order to improve the dispersion of silica nanoparticles in PMMA matrix, the silanol groups of the silica are functionalized with methyl methacrylate groups and modified nanoparticles were used to synthesize PMMA/modified silica nanocomposites via RAFT polymerization. Prepared samples were characterized by thermogravimetric analysis (TGA), dynamic light scattering (DLS), dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC) and gel permeation chromatography (GPC). According to results, introduction of modified nanoparticles results in better thermal and mechanical properties than those of pristine nanoparticles. Also, surface modification and increasing silica nanoparticles result in variation of thermal degradation behavior of nanocomposites. The best improvement of mechanical and thermophysical properties is achieved for nanocomposites containing 7 wt. % silica nanoparticles.     

Electrocatalytic oxidation of methanol on the nickel–cobalt modified glassy carbon electrode in alkaline medium

In this work, Ni–Co alloy coating on the surface of glassy carbon (GC) electrode was performed by cyclic voltammetry. The results showed that the deposition of Ni–Co is an anomalous process. The deposition bath was prepared according to the metal ion Ni/Co ratio of 4:1 using NiSO₄·7H₂O and CoSO₄·8H₂O, and the total concentration of all solutions was 40.0 mM. The pH of the bath solution was adjusted at 2.0 using boric acid at room temperature. The modified electrode was conditioned by potential recycling in a potential range of 100–700 mV (vs. Ag/AgCl) by cyclic voltammetric method in an alkaline solution. The Ni–Co modified electrode showed a higher activity towards methanol oxidation in the Ni (III) and Co (IV) oxidation states. Cyclic voltammetry was used for the electrochemical characterization of the Ni–Co modified electrode and the mechanism of methanol oxidation is proposed. The result of double steps chronoamperometry shows that the methanol electrooxidation is an irreversible reaction. Moreover, the effects of various parameters such as mole ratio of Ni–Co in the alloy in modification step, potential scan rate, methanol concentration and solution temperature on the electro-oxidation of methanol have also been investigated.     

Highly efficient supported AlCl3-based cationic catalysts to produce polyα-olefin oil base stocks

The main aim of this research is to decrease the amount of AlCl₃ content that is very corrosive and hazardous in the catalytic system, required for the α-olefin oligomerization without substantial change of final oil features. This was successfully achieved by supporting AlCl₃ on different carriers. More precisely, a series of supported bimetallic catalysts was synthesized by immobilization of AlCl₃ and TiCl₄ onto Al₂O₃, SiO₂, and mixed supports, that is, Al₂O₃/FeCl₃ and SiO₂/FeCl₃. It was found that silica and alumina-based catalysts had higher catalytic activities compared to support free AlCl₃; however, this enhancement for silica-based supports was more significant. According to gel permeation chromatography (GPC) results, the use of single supports, that is, Al₂O₃ and SiO₂, increased oligomer's molecular weight, while the application of mixed supports resulted in the decrease of molecular weight of the oligomers. Viscosity characteristics of the synthesized oligomers have also been studied at two different temperatures of 40 and 100°C (KV⁴⁰ and KV¹⁰⁰). The viscosity index (VI) values, derived from KV⁴⁰ and KV¹⁰⁰, of the prepared oligomers were in the range of 126–145. The molecular weight and termination mechanisms of the oligomers were studied by ¹H-NMR spectroscopy. The obtained results disclosed that the employed reaction conditions led to the production of oligomer chains with various structures including vinylidene (Vd), and di and three-substituted vinylene (2Vn, 3Vn) structures.     

Mechanical and high velocity impact performance of a hybrid long carbon/glass fiber/polypropylene thermoplastic composite

This research explores mechanical and high velocity impact response of hybrid long carbon/glass fiber-reinforced polypropylene thermoplastic composites (HLFT) with different fiber lengths. The work examines three hybrid long fiber thermoplastic composites, i.e., 5, 10 and 20 mm. The HLFTs were prepared by a combination of extrusion and pultrusion processes and using a cross-head die. Tensile and Izod impact tests were carried out to evaluate the mechanical performance of each HLFT compound. A gas gun with a spherical projectile was used to conduct high velocity impact tests at three velocities of 144, 205 and 240 m/s. The results showed that internal mixing operation caused extensive reduction in fiber length of all three LFT lengths. Tensile strength, modulus and Izod impact test results were the indications of higher values with increase in HLFT length. Comparison of these results for the HLFT with that of corresponding glass/PP LFTs, adopted from earlier work by Shayan Asenjan et al. (J Compos Mater 53:353–360, 2019), showed better performance of HLFT. The high velocity impact results showed a steady higher impact performance with the increase in HFLT fiber length for all impact velocities tested. Comparison of HLFT high velocity impact performance revealed better results for all impact velocities tested with that of the corresponding glass/PP LFT composite.     

Direct extraction of Mo(VI) from sulfate solution by synergistic extractants in the rotation column

Direct extraction of molybdenum from sulfate solution with synergistic extractants (mixture of D₂EHPA and TBP) was studied in the rotation column. The influence of extractant concentration and initial pH of aqueous phase was studied in the bench scale experiments. The outcomes demonstrated that the synergistic solvent extraction enhances the constancy of the extracted complexes for transfer into the organic phase. In the continuous experiments, the effect of different operating parameters such as speed of agitation, inlet solvent flow rate and inlet aqueous flow rate on the holdup, mean drop size, drop size distribution, slip and characteristic velocities and extraction percentage were examined. Modified correlations were proposed for prediction of hydrodynamic parameters with consideration of reaction extraction condition in the rotation column. Furthermore, these correlations were compared with the experimental data. According to the results, the direct extraction of Mo (VI) from aqueous solution and sulfuric media with extraction efficiency of 90.4% was obtained at higher rotor speed (240 r·min^-1 rpm) in this column.     

Effect of preparation and operation conditions on the catalytic performance of cobalt-based catalysts for light olefins production

Cobalt-based catalysts were prepared by precipitation method. This research investigated the effects of different supports cobalt loading, promoters, loading of promoters and calcination conditions on the catalytic performance of cobalt catalysts for Fisher-Tropsch synthesis (FTS). It was found that the catalyst containing 40 wt.% Co/TiO₂ promoted with 6 wt.% Zn was an optimal catalyst for the conversion of synthesis gas to hydrocarbons especially light olefins. The activity and selectivity of optimal catalyst were studied in different operational conditions. The results showed that the best operational conditions were the H₂/CO = 2/1 molar feed ratio at 240 °C and GHSV = 1100 h⁻¹ under atmospheric pressure. Characterization of catalysts were carried out by using X-ray diffraction (XRD), thermal gravimetric analysis (TGA), hydrogen temperature program reduction (H₂-TPR), N₂ physisorption measurements such as Brunauer-Emmett-Teller (BET) and Barrett-Joyner-Halenda (BJH) methods.     

Expression of Main Toll-Like Receptors in Patients with Different Types of Colorectal Polyps and Their Relationship with Gut Microbiota

Abnormal activation of Toll-like receptor (TLRs) signaling can result in colon cancer development. The aim of this study was to investigate the expression of important TLRs in different histological types of colorectal polyps and evaluate their relationship with intestinal microbiota. The expression levels of TLR2, 3, 4, and 5 were analyzed in intestinal biopsy specimens of 21 hyperplastic polyp (HP), 16 sessile serrated adenoma (SSA), 29 tubular adenoma (TA), 21 villous/tubulovillous (VP/TVP) cases, and 31 normal controls. In addition, selected gut bacteria including Streptococcus bovis, Enterococcus faecalis, Enterotoxigenic Bacteroides fragilis (ETBF), Fusobacterium nucleatum, Porphyromonas spp., Lactobacillus spp., Roseburia spp., and Bifidobacterium spp. were quantified in fecal samples using absolute qRT PCR, and, finally, the association between TLRs and these gut microbiota- was evaluated by Spearman’s correlation coefficient. Higher expression of TLR2 and TLR4 in VP/TVP and TA, and lower expression levels of TLR3 and TLR5 in all type of polyps were observed. The differences in TLR expression patterns was not only dependent on the histology, location, size, and dysplasia grade of polyps but also related to the intestinal microbiota patterns. TLR2 and TLR4 expression was directly associated with the F. nucleatum, E. faecalis, S. bovis, Porphyromonas, and inversely to Bifidobacterium, Lactobacillus, and Roseburia quantity. Furthermore, TLR3 and TLR5 expression was directly associated with Bifidobacterium, Roseburia, and Lactobacillus quantity. Our results suggest a possible critical role of TLRs during colorectal polyp progression. An abnormal regulation of TLRs in relation to gut microbial quantity may contribute to carcinogenesis.     

Photocatalytic degradation of diclofenac using hybrid MIL-53(Al)@TiO2 and MIL-53(Al)@ZnO catalysts

In this work, TiO₂ and ZnO were incorporated successfully into a MIL-53(Al) metal–organic framework (MOF) to form nanocomposites via a facile post-modification technique. The hybrid MIL-53(Al)@TiO₂ and MIL-53(Al)@ZnO were characterized by several characterization tests. The X-ray diffraction (XRD), Fourier-transform infrared (FTIR), and field-emission scanning electron microscopy (FE-SEM) analyses showed evidence of the successful incorporation of TiO₂ and ZnO within the MIL-53(Al) framework. The thermal gravimetric analysis (TGA) analysis demonstrated the excellent thermal stability of MIL-53(Al)@TiO₂ and MIL-53(Al)@ZnO, while diffuse reflectance spectroscopy (DRS) determined the direct optical band gaps of MIL-53(Al)@ZnO and MIL-53(Al)@TiO₂ to be 3.24 and 3.34 eV, respectively. The composites were also tested for the photocatalytic degradation of diclofenac (DCF) as a micropollutant. The DCF degradation efficiency of the photocatalysts was ranked in the following order: MIL-53(Al)@TiO₂ > MIL-53(Al) > TiO₂ > ZnO > MIL-53(Al)@ZnO. The incorporation of TiO₂ enhanced the optical properties of MIL-53 (Al), which was confirmed with the superior photodegradation efficiency of MIL-53(Al)@TiO₂ (>85% in 2 h) as compared to the pristine MIL-53(Al) (around 80% in 2 h). The improvement in the photodegradation of the hybrid-MOF is mostly associated with the possible dual function of the adsorption and photodegradation mechanisms. The reusability of MIL-53(Al) and its composites was inspected over 3 cycles of photodegradation experiments with DCF. The photocatalytic activity of MIL-53(Al)@TiO₂ remained unchanged (>90%), while for MIL-53(Al) and MIL-53(Al)@ZnO a slight drop was observed over three cyclic degradation experiments. Fluorescence measurements revealed that the hydroxyl radical is an important reactive oxygen species produced by all the photocatalysts that aid in the photodegradation of DCF. Furthermore, the kinetic modelling of the photoreaction identified a second-order kinetics for all catalysts. Experiments with scavengers showed that hydroxyl radicals played a major role in the photocatalytic process, and it was found that only 2 h of treatment was sufficient to obtain a considerable chemical oxygen demand (COD) reduction of 58%.