Novel Fault Management Framework Using Markov Chain in Wireless Sensor Networks: FMMC

Wireless Personal Communications - Due to using wireless sensor nodes (WSNs) in inaccessible areas and applying limitations in making nodes to reduce costs, these networks are prone to faults. The...     

Hybrid solar parabolic dish power plant and high‐temperature phase change material energy storage system

In this study, a conventional steam power plant with two regenerative boilers is considered, and one of its boilers is replaced with parabolic solar dish collectors and storing the produced thermal energy by the phase change material (PCM) in a storage tank. The results show the necessity of the existence of an auxiliary fired‐gas boiler to provide constant load during the whole 24 hours. The performance of the proposed hybridized system is evaluated through energy and exergy analyses. It was demonstrated that substituting solar collectors with one of the boilers marginally lowers the energy efficiency but increases the exergy efficiency of the whole power plant up to 41.76%. Moreover, it is found out that this hybridization decreases the total irreversibility of the power plant in comparison with the base case, from 51.1 to 47.2 MW. The parametric analysis states that raising the mass flow rate of the heat transfer fluid in the solar collectors not only enhances the system performance but also increases the volume of the PCM tank.     

Describing a strategy to estimate the CO2-heavy oil minimum miscibility pressure based on the experimental methods

To measure MMP, slim tube method is time consuming, especially for heavy oils. In this study, a strategy is considered to measure the MMP in one of the Iranian heavy oil reservoirs. The strategy steps were done through; partial data of slim tube, coupling numerical model (CNM), full slim tube, and VIT test. The results showed that CNM technique with two experimental data obtains the MMP value faster than running a full slim tube with low error result. However, VIT determined MMP faster and its results illustrated that miscibility pressure for heavy oil occurs at zero IFT, unlike light oils.     

Development of a Robust Carrier Synchronizer for High Dynamic and Low Signal to Noise Ratio Signals in GPS Receivers

Wireless Personal Communications - In this paper, a robust carrier recovery loop for high dynamic and weak signals in GPS receivers is proposed. To achieve optimal tracking performance at...     

Rotational and axial flow of pseudoplastic fluids

Mechanics of Time-Dependent Materials - Effects of a controllable axial flow on the stability of rotational flow of pseudoplastic fluids in the gap between concentric cylinders are studied. It is...     

On the numerical solution of Fredholm integral equations utilizing the local radial basis function method

The current investigation describes a computational technique to solve one- and two-dimensional Fredholm integral equations of the second kind. The method estimates the solution using the discrete collocation method by combining locally supported radial basis functions (RBFs) constructed on a small set of nodes instead of all points over the analysed domain. In this work, we employ the Gauss–Legendre integration rule on the influence domains of shape functions to approximate the local integrals appearing in the method. In comparison with the globally supported RBFs for solving integral equations, the proposed method is stable and uses much less computer memory. The scheme does not require any cell structures, so it is meshless. We also obtain the error analysis of the proposed method and demonstrate that the convergence rate of the approach is high. Illustrative examples clearly show the reliability and efficiency of the new method.     

Effect of baking in different ovens on the quality and structural characteristics of saltine crackers

The aim of the study was to evaluate the physical and microstructural characteristics of crackers baked in four different industrial baking ovens (indirect radiation-cyclotherm, indirect convection, hybrid and industrial tunnel-ITO). Indirect convection and cyclotherm ovens provide the highest (5685.43 ± 51 W m⁻²) and the lowest (4860 ± 38.87 W m⁻²) amount of heat flux, respectively. Despite the amount of heat flux, indirect convection led to crackers with the highest moisture (7.86% vs. 4.82% in clyclotherm) and specific volume, but the lowest hardness. Cyclotherm resulted in crackers with lower specific volume, surface area, porosity, smooth and regular surface. Conversely, the hybrid and ITO ovens showed closer heat flux, leading to crackers with similar moisture content, texture parameters, specific volume, browning and inner porosity. Overall results show the potential of baking using different ovens for modifying the quality parameters of the crackers.     

Electrical and Mechanical Behavior of Aerosol Jet–Printed Gold on Alumina Substrate for High-Temperature Applications

There is a growing interest in the development of microelectronics that can perform reliably and robustly at temperatures above 300 °C. Such devices require stable thermal properties, low thermal drift, and thermal cycling resistance. Conventional hybrid circuit technology demonstrates high-temperature packages, but the high costs and lead time are significant drawbacks. In contrast, additive manufacturing processes, including aerosol jet printing (AJP), offer cost and time benefits, as well as 3D structures and embedded features. However, the properties and reliability of additive packaging materials at extreme temperatures are not well known. Herein, the reliability at temperatures up to 750 °C in terms of electrical performance and mechanical strength of aerosol jet printed gold thick films onto ceramic substrates are assessed. Thermal coefficient of resistance of printed gold films is measured. The electrical resistance stability and leakage current of printed gold structures are also characterized during over 100 h of aging at temperatures up to 750 °C. Finally, the mechanical adhesion strength of the printed gold films is evaluated after aging for 100 h at temperatures up to 750 °C. The adhesion of the printed gold to the ceramic substrates remains high after aging, very stable resistances and minimal leakage currents have been observed.     

ABSs系统模糊控制器优化设计

已经开发了的ABSs系统改善了突然制动和特别是滑动路面状况时车辆控制。这样的控制目标是在保持车辆合适稳定性及可操纵性和缩短车辆刹车距离情况下在要求的方向增大车轮的牵引力。本文提出了ABSs系统优化的模糊控制器。从保持其车轮滑动值为目标函数获得车轮最大的牵引力和车轮最大的减速度。采用遗传算法优化模糊系统的全部组件。采用误差数整体优化方法收敛接近最优点。仿真结果表明快速收敛和对不同路况的控制器的最好性能。