频谱分析仪现行检定规程与校准规范的对比研究

本文对比介绍了JJF1396-2013《频谱分析仪校准规范》与GJB/J 5859-2006《宽频带频谱分析仪检定规程》的检定校准项目、方法及相关要求,为频谱分析仪的检定校准工作开展提供参考借鉴。     

快/慢烤试验中复合推进剂内部温度场的分布

为了研究不同烤燃条件下复合推进剂(PBT/HMX/Al/AP/BU)的响应特性,采用DSC研究了复合推进剂及单组分的热分解特性。复合推进剂的初始分解温度为187.27℃,单组分中BU初始分解温度最低,为192.95℃,表明复合推进剂的热分解过程是从BU开始;分别测量了在快/慢烤试验中,复合推进剂内部温度的变化。结果表明:1)快烤试验中,样品内部温度分布极不均匀。点火90 s后,样品发生反应,此时样品中心的温度为85℃,钢管端盖破裂,样品发生燃烧反应。2)慢烤试验中,样品内部温度分布均匀,几乎无温度差,样品发生反应时,样品内部温度与环境温度均为133℃,试验后样品钢管完全破碎,样品发生了爆轰。由此可见,慢烤试验中,由于样品内部温度分布均匀,发生反应时,大部分样品都处于临界反应温度,一旦激发,破坏效应比快烤试验更严重。     

气相色谱仪新旧检定规程的解读

本文主要从规程适用范围、计量器具控制、计量性能要求及检定方法等方面入手,全面的解读了气相色谱仪新旧检定规程的差异,为仪器检定及期间核查提供了参考。     

液相色谱法测定水中苯丙[a]芘的不确定度评估

对液相色谱法测定生活饮用水中苯丙[a]芘含量测量不确定度进行分析,为评价检测数据的准确性提供科学依据。测样量为1m L时,测定生活饮用水中苯丙[a]芘含量为ρ=(0.856+0.025)μg·m L-1。通过对不确定度来源的量化分析,得出标准物质引入的不确定度分量和线性误差引入的不确定度分量是测定结果不确定度的重要来源。     

Mechanical Properties and Interlaminar Fracture Toughness of Glass‐Fiber‐Reinforced Epoxy Composites Embedded with Shape Memory Alloy Wires

The effects of the content and position of shape memory alloy (SMA) wires on the mechanical properties and interlaminar fracture toughness of glass‐fiber‐reinforced epoxy (GF/epoxy) composite laminates are investigated. For this purpose, varying numbers of SMA wires are embedded in GF/epoxy composite laminates in different stacking sequences. The specimens are prepared by vacuum‐assisted resin infusion (VARI) processing and are subjected to static tensile and three‐point‐bending tests. The results show that specimens with two SMA wires in the stacking sequence of [GF₂/SMA/GF₁/SMA/GF₂] and four SMA wires in the stacking sequence of [GF₄/SMA/GF₂/SMA/GF₄] exhibit optimal performance. The flexural strength of the optimal four‐SMA‐wire composite is lower than that of the pure GF/epoxy composite by 5.76% on average, and the flexural modulus is improved by 5.19%. Mode‐I and II interlaminar fracture toughness tests using the SMA/GF/epoxy composite laminates in the stacking sequence of [GF₄/SMA/GF₂/SMA/GF₄] are conducted to evaluate the mechanism responsible for decreasing the mechanical properties. Scanning electron microscopy (SEM) observations reveal that the main damage modes are matrix delamination, interfacial debonding, and fiber pullout.