Optimization of Automated Synthesis of 2-[18F]Fluoro-2-deoxy-D-glucose Involving Base Hydrolysis

Synthesis of 2-[¹⁸F]fluoro-2-deoxy-D-glucose ([¹⁸F]FDG) involving base hydrolysis was optimized. Fluorine-18 was isolated from irradiated water to more than 90% by sorption of [^{1 8}F]fluoride on QMA anion-exchange resin, which was followed by elution with a 96 : 4 (by volume) acetonitrile-water mixture containing Kryptofix 2.2.2 and potassium carbonate (molar ratio 2 : 1). This composition is the best for preparing the complex [K/K2.2.2]^{+ 18}F^- used in nucleophilic fluorinations. No additional azeotropic drying is required. Base hydrolysis under optimized conditions (40-45°C), followed by neutralization with HCl, removal of traces of the solvent, and purification of the final product on a combined SCX/Alumina N column, yielded [^{1 8}F]FDG of high radiochemical (>99%) and chemical purity with minimal product loss. With an RB-86 robotic system (Anatech, Sweden), the synthesis time was 38 min. The procedure is used in the Institute of Human Brain, Russian Academy of Sciences for routine synthesis of FDG; the radiochemical yield of the product by the end of synthesis (EOS) is reproducibly high: 63±3% (n = 40).     

Top-Seeded Melt-Growth of YBa2Cus3Ox Crystals for Neutron Diffraction Studies

We have grown cubic centimeter-size crystals of YBa₂Cu₃O _x suitable for neutron studies, by a top-seeded melt-growth technique. Growth conditions were optimized with an eye toward maximizing phase purity. It was found that the addition of 2% Y₂BaCuO₅ and 0.5% Pt (by mass) were required to prevent melt loss and to obtain the highest crystallinity. A neutron diffraction study on a mosaic of six such crystals found that the final Y₂BaCuO₅ concentration was 5%, while other impurity phases comprised less than 1% by volume. The oxygen content was set to x = 6.5, the crystals were detwinned, and then carefully annealed to give the well-ordered ortho-II phase. The neutron study determined that 70% of the mosaic's volume was in the majority orthorhomic domain. The neutron (006) and (110) rocking curve widths were ～1° per crystal and ～2.2° for the mosaic, and the oxygen chain correlation lengths were >100 Å in the a- and b-directions and ～50 Å in the c-direction.     

Equal-channel angular extrusion of beryllium

The equal-channel angular extrusion (ECAE) technique has been applied to a powder metallurgy (P/M) source Be alloy. Extrusions have been successfully completed on Ni-canned billets of Be at approximately 425°C. No cracking was observed in the billets, and significant grain refinement was achieved. In this article, microstructural features and dislocation structures are discussed for a singlepass extrusion, including evidence of <c> and <c+a> dislocations. Significant crystallographic texture developed during ECAE, which is discussed in terms of this unique deformation processing technique and the underlying physical processes which sustain the deformation. S.R. AGNEW, formerly with the Oak Ridge National Laboratory, Oak Ridge, TN 37831-6115 This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Simulation of magnetic component models in electric circuitsincluding dynamic thermal effects

It is essential in the simulation of power electronics applications to model magnetic components accurately. In addition to modeling the nonlinear hysteresis behavior, eddy currents and winding losses must be included to provide a realistic model. In practice the losses in magnetic components give rise to significant temperature increases which can lead to major changes in the component behavior. In this paper a model of magnetic components is presented which integrates a nonlinear model of hysteresis, electro-magnetic windings and thermal behavior in a single model for use in circuit simulation of power electronics systems. Measurements and simulations are presented which demonstrate the accuracy of the approach for the electrical, magnetic and thermal domains across a variety of operating conditions, including static thermal conditions and dynamic self heating     

Front Cover

In this paper, the authors present the results of experiments which clearly demonstrate a technical basis confirming that the carrier frequency harmonics data can be used for diagnostics relative to motor stator insulation degradation.     

Determination of dislocation densities in HCP metals from X-ray diffraction line-broadening analysis

X-Ray diffraction (XRD) line-broadening analysis has been performed on highly textured Zr-2.5Nb specimens which had been deformed in tensile tests to produce well-controlled dislocation structures. An iterative deconvolution method has been applied to extract the broadening function for the material, using as standards, a Zr single crystal and a 0 pct deformed specimen. In both cases, for specific tensile tests, a significant contribution to the basal line braodening was observed, which was clearly not directly related to the dislocation structure generated by the deformation, i.e., so-called c-component dislocations having a component of their Burgers vectors perpendicular to the basal plane. Calculations showed that the extent of basal line broadening cannot be attributed to the secondary effect of strain from a-type dislocations, i.e., dislocations with Burgers vectors parallel with the basal plane. It is concluded that most of the line broadening observed was the result of intergranular strain distributions. These distributions are most prominent for grains oriented with their c-axes perpendicular to the tensile-deformation axis and resulted in basal-plane line broadening even when there were few, if any, c-component dislocations present. This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science and Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

Automatic conversion from lexical words to prosodic words for mandarin text-to-speech system

In real speech, not like lexical words (LWs), prosodic words (PWs) are basic rhythmic units. The naturalness of a Text-to-Speech (TTS) system is directly influenced by the segmentation of the PWs. Most of the PWs are the combination of several LWs. In this paper, three Lexical Combination Models are proposed to combine LWs into PWs, including a Directed Acyclic Graph Model, a Segmentation Model and a Markov Model (MM). To cope with the situation where some long LWs should be segmented into two or more PWs, a Lexical Split Model (LSM) is applied to the long LWs. Experimental results prove that relatively constant results with various training data can be obtained from a MM. The Transformation-Based Error Driven Learning (TBED) algorithm, for its high performance of individual property, is applied in combination with the MM to improve the precision of PW segmentation. Experiments show that among the three proposed models, the MM combined with TBED and LSM, leads to the best performance, in which a precision of 93.00% and a recall of 93.23% are achieved. The perception test indicates that by using PWs as the lowest prosodic units a speech sounds more natural and acceptable than by using LWs. This paper is supported by NSFC Project (60503071); 973 Natural Basic Research Program of China (2004CB318102); Postdoctor Science Foundation of P. R. China (20070420275).     

Critical Configurations for 1-View in Projections from ℙ<Superscript>k</Superscript> → ℙ<Superscript>2</Superscript>

In this paper we describe, from a theoretical point of view, critical configurations for the projective reconstruction of a set of points, for a single view, i.e. for calibration of a camera, in the case of projections from ℙ^k to ℙ² for k ≥ 4. We give first a general result describing these critical loci in ℙ^k, which, if irreducible, are algebraic varieties of dimension k−2 and degree 3. If k=4 they can be either a smooth ruled surface or a cone and if k = 5 they can be a smooth three dimensional variety, ruled in planes, or a cone. If k≥ 6, the variety is always a cone, the vertex of which has dimension at least k − 6. The reducible cases are studied in Appendix A. These results are then applied to determine explicitly the critical loci for the projections from ℙ^k which arise from the dynamic scenes in ℙ³ considered in [13]. Marina Bertolini is currently Associate Professor of Geometry at the Department of Mathematics at the Università degli Studi di Milano, Italy. Her main field of research is Complex Projective Algebraic Geometry, with particular interest for the classification of projective varieties and for the geometry of Grassmann varieties. On these topics M. Bertolini has published more than twenty reviewed papers on national and international journals. She has been for some years now interested also in applications of Algebraic Geometry to Computer Vision problems. Cristina Turrini is Associate Professor of Geometry at the Department of Mathematics of Università degli Studi di Milano, Italy. Her main research interest is Complex Projective Algebraic Geometry: subvarieties of Grassmannians, special varieties, automorphisms, classification. In the last two years she has started to work on applications of Algebraic Geometry to problems of Computer Vision. She is author or co-author of about thirty reviewed papers. She is also involved in popularization of Mathematics, and on this subject she is co-editor of some books.