Separation of di- and tripeptides with solvent extraction and an emulsion liquid membrane

The extraction equilibria of various di- and tripeptides with di-2-ethylhexylphosphoric acid (D2EHPA) were studied at low pH values. The complex extracted to organic phase consisted of one molecule of peptide and two molecules of D2EHPA dimer. The extraction constants of the peptides correlated well with the distribution coefficients of peptides between 1-octanol and water, which is a measure of hydrophobicity. The permeation rates of peptides through an emulsion liquid membrane were examined by using D2EHPA as a carrier, Span 80 as an emulsifier and kerosene as a diluent. The rates varied considerably with peptide type, depending upon the hydrophobicity.     

Coupling ratio control of polymeric waveguide couplers by bending

Directional couplers are successfully fabricated on acrylic substrates using polymers synthesised from deuterated methacrylate and deuterated fluoromethacrylate monomers. The excess loss of a 50 mm long coupler is about 0.7 dB including waveguide and fibre coupling losses. A novel method is proposed for tuning the coupling ratio. By bending the coupler, high precision control of within 1% is attained without optical polarisation dependence.<>     

Transflective IPS‐LCD with improved reflective contrast ratio

Abstract— In order to improve the reflective contrast ratio of transflective IPS‐LCDs, a novel pixel design for a normally white reflective IPS has been proposed. In this design, the large‐inter‐electrode‐spacing layout using a novel driving method and a double‐layered electrode have effectively reduced the light leakage. By applying these two technologies, a transflective IPS‐LCD has been successfully demonstrated with a high contrast ratio (15:1) in the reflective mode and a wide‐viewing‐angle characteristic in the transmissive mode.     

Measurement of Flow Stress in Supercooled Austenite for High Hardenability Steel

In this article, the isothermal flow stress in supercooled austenite was measured for a high hardenability steel. Supercooled austenite forms at the nonequilibrium phase and changes into other phases within a short time. It was confirmed that conventional tensile tests, which require maintaining a constant temperature before stretching, cannot accurately measure the flow stress in supercooled austenite. Therefore, a new tensile test named “the continuous cooling tensile test” was developed. In this test, stretching is conducted during continuous cooling. In the continuous cooling tensile test, the flow stress between 673 K and 973 K (400 °C and 700 °C) was measured. Microscopic observations of the continuous cooling test results verified that the microstructures were supercooled austenite.     

First plasma experiment on spherical tokamak device UTST

The UTST (University of Tokyo Spherical Tokamak) device was constructed for the purpose of exploring the formation of ultrahigh‐beta ST (spherical tokamak) plasma using the double null plasma merging method. When two plasmas merge together to form a single plasma, magnetic field lines reconnect, and magnetic field energy is converted to plasma kinetic energy, increasing the plasma beta. Merging start‐up has been demonstrated in the TS‐3/4, START, and MAST devices using coils inside the vacuum vessel, and the TS‐3 plasma obtained a 50% beta. In order to demonstrate start‐up in a more reactor‐relevant situation, UTST has all poloidal field (PF) coils outside the vacuum vessel. The first plasma experiment on the UTST was begun in December 2007. In the results, the plasma obtained 10 kA by using only the outer PF coils and a single ST was generated in the lower area (z = –0.3 to –1.0 m) close to a washer gun. This result suggests that another washer gun on the top of the UTST can allow the generation of ST in the upper area and merging start‐up by using outer PF coils. © 2012 Wiley Periodicals, Inc. Electr Eng Jpn, 179(2): 20–26, 2012; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21216     

A straight-bladed vertical axis wind turbine with a directed guide vane row — Effect of guide vane geometry on the performance —

The objective of this study is to show the effect of guide vane geometry on the performance. In order to overcome the disadvantages of vertical axis wind turbine, a straight-bladed vertical axis wind turbine (S-VAWT) with a directed guide vane row has been proposed and tested by the authors. According to previous studies, it was clarified that the performance of the turbine can be improved by means of the directed guide vane row. However, the guide vane geometry of S-VAWT has not been optimized so far. In order to clarify the effect of guide vane geometry, the effects of setting angle and gap between rotor blade and guide vane on power coefficient and starting characteristic were investigated in the experiments. The experimental study of the proposed wind turbine was carried out by a wind tunnel. The wind tunnel with a diameter of 1.8m is open jet type. The wind velocity is 8 m/s in the experiments. The rotor has three straight blades with a profile of NACA0018 and a chord length of 100 mm, a diameter of 0.6 m and a blade height of 0.7 m. The guide vane row consists of 3 arc plates.     

Impact of the gate-drain overlapped device (GOLD) for deepsubmicrometer VLSI

The gate-drain overlapped device (GOLD) structure is proposed to achieve high reliability and high performance in deep submicrometer MOSFETs. The GOLD device concept is different from that of drain-engineering methods such as the double-diffused drain (DDD) and lightly doped drain (LDD). GOLD eliminates the tradeoff between transconductance and breakdown voltage (hot-carrier, drain sustaining). The overlap effect of the GOLD devices is discussed using simulation and experiment. GOLD has a gate structure using a native oxide film (5-10 A) to obtain an overlapped fine structure. The process is also compatible with conventional LDD processes and is suitable for 0.3-0.5-μm-design-rule devices at 5-V operation, and 3-V operation     

Acetaminophen-Induced Rat Hepatotoxicity Based on M1/M2-Macrophage Polarization,in Possible Relation to Damage-Associated Molecular Patterns and Autophagy

Overdose of acetaminophen (APAP), an antipyretic drug, is an important cause of liver injury. However, the mechanism in the rat model remains undetermined. We analyzed APAP-induced hepatotoxicity using rats based on M1/M2-macrophage functions in relation to damage-associated molecular patterns (DAMPs) and autophagy. Liver samples from six-week-old rats injected with APAP (1000 mg/kg BW, ip, once) after 15 h fasting were collected at hour 10, and on days 1, 2, 3, and 5. Liver lesions consisting of coagulation necrosis and inflammation were seen in the affected centrilobular area on days 1 and 2, and then, recovered with reparative fibrosis by day 5. Liver exudative enzymes increased transiently on day 1. CD68⁺ M1-macrophages increased significantly on days 1 and 2 with increased mRNAs of M1-related cytokines such as IFN-γ and TNF-α, whereas CD163⁺ M2-macrophages appeared later on days 2 and 3. Macrophages reacting to MHC class II and Iba1 showed M1-type polarization, and CD204⁺ macrophages tended to be polarized toward M2-type. At hour 10, interestingly, HMGB1 (representative DAMPs) and its related signals, TLR-9 and MyD88, as well as LC3B⁺ autophagosomes began to increase. Collectively, the pathogenesis of rat APAP hepatotoxicity, which is the first, detailed report for a rat model, might be influenced by macrophage functions of M1 type for tissue injury/inflammation and M2-type for anti-inflammatory/fibrosis; particularly, M1-type may function in relation to DAMPs and autophagy. Understanding the interplayed mechanisms would provide new insight into hepato-pathogenesis and contribute to the possible development of therapeutic strategies.