Changes in pore properties of phenol formaldehyde-based carbon with carbonization and oxidation conditions

Porous carbon beads were prepared by carbonizing at 700 and 1000 °C under N₂ (NN-series) or CO₂ atmospheres (CO-series) and a subsequent oxidization with boiling nitric acid solution (13%, v/v) for 3 h (ANN- and ACO-series). BET surface area of both CO- and NN-series samples tends to increase with increasing carbonization temperature, but CO-series samples show higher BET surface areas (700 °C: 610 m²/g, 1000 °C: 780 m²/g) compared with those of NN-series samples (700 °C: 380 m²/g, 1000 °C: 580 m²/g). After acid oxidation, BET surface areas of NN-series samples increased from 580 to 650 m²/g, whereas those of CO-series samples decreased from 780 to 600 m²/g. On subsequent acid oxidation, acidic surface functional groups increased in both CO- and NN-series samples, but the CO-series samples tend to have much more acidic surface functional groups. Adsorption of halogenated methanes, such as tetra-, tri- and dichloromethanes, onto the samples of CO-, NN-, ACO- and ANN-series was thought to be driven initially by the basicity, but the acidic functional groups that could attract adsorbates via dipole-dipole interaction might hinder the adsorption of subsequently incoming adsorbates.     

Heavy oil sorption and recovery by using carbon fiber felts

On fibrous carbon materials, including activated carbon fibers, sorption capacity for heavy oils, less viscous A-grade and more viscous C-grade, was determined. Sorption capacity depended strongly on their bulk density; the correlation was the same as that found previously on exfoliated graphite and carbonized fir fibers. On carbon fiber felts, excellent recycling performance was observed, though sorption capacity was not so high as on exfoliated graphite and carbonized fir fibers. By filtration under suction, about 90% of sorbed A-grade heavy oil could be recovered and no decrease in sorption capacity was detected even after eight cycles. By washing with solvents, n-hexane for A- and C-grade oils and A-grade oil for C-grade oil, almost 100% recovery with no marked reduction in sorption capacity was found for each cycle. For the felts of PAN-based carbon fibers, rather severe operations for oil recovery, centrifugation and squeezing with twisting, could be applied without pronounced decreases in sorption capacity and recovery ratio.     

Micrinite and exudatinite in some Australian coals,and their relation to the generation of petroleum

The occurrence and microscopic features of micrinite and exudatinite in some Australian coals are reported. The origin of these macerals and also the significance of their occurrence are discussed in connection with hydrocarbon genesis. In Australia, micrinite occurs in bituminous and sub-bituminous coals which are very rich in inertinite, and also in brown coal rich in inertinite. One of the possible progenitors of micrinite is oxidized porigelinite. There is little reason to conclude that micrinite was formed from resinite and other macerals at an early stage of coalification and that liquid hydrocarbons were formed during this process. Exudatinite occurs in sub-bituminous and high-volatile bituminous coals in the Gippsland Basin. There is no positive evidence of a genetic relation between liquid hydrocarbons, exudatinite, micrinite and liptinite macerals. The formation of liquid hydrocarbons from solid liptinite etc. may take place just before and during Teichmüller's so-called ‘2nd coalification jump’.     

A study on capacity fading of lithium-ion battery with manganese spinel positive electrode during cycling

The capacity fading mechanism of lithium-ion cell was studied by disassembling the charge-discharged cells and analyzing their electrodes using scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS), etc. Cu ion dissolved from current collector of anode and Mn ion dissolved from LiMn₂O₄ spinel (cathode) were all existing in solid electrolyte interface (SEI) layer on carbon anode as Cu₂O and MnO or MnO₂, respectively. These depositions of Cu and Mn oxides did not uniformly deposited on the anode side, and most of them were detected on the carbon surface nearby to the separator side. The SEI layer is hard and about 0.3 μm in thickness. Furthermore, the cycling performance of the cells can be improved by adding 1,2,3-benzotrazole (a corrosion inhibitor of Cu) before assembling the cell, it then coordinates strongly with Cu ions into the electrolyte. From the results, it is obvious that the existing of Cu oxide as well as Mn oxide in the SEI layer, which blocks the normal intercalation of the lithium ions, is one of the factors for the capacity fading of the cells.     

PIV and PTV measurements in hydro-sciences with focus on turbulent open-channel flows

PIV is one of the most popular measurement techniques in hydraulic engineering as well as in fluid sciences. It has been applied to study various turbulent phenomena in laboratory experiments related to natural rivers, e.g., bursting phenomena near the bed, mixing layers observed at confluences, wake turbulence around dikes and piers, and so on. In these studies, PIV plays important roles in revealing the space-time structure of velocity fluctuations and coherent vortices. This review article focuses particularly on the applications of PIV to turbulent open-channel flows, which have been conducted for the past decade in Hydraulics Laboratory of Kyoto University. In Section 2, we introduce our experimental setup and PIV/PTV algorithm. In Section 3, we apply the PIV measurements to reveal turbulence characteristics and coherent structures in open-channel flows as well as in vegetated canopy flows. For complex flow situations, various applications of PIV to compound open-channel flows and wind-induced water waves are considered to reveal coherent vortices. In Section 4, we discuss some advanced PIV measurements in open-channel flows. The free-surface-elevation fluctuations and velocity components were measured simultaneously with two sets of cameras to examine phase-averaged parameters of turbulence. A multi-layer scanning PIV was developed to reveal 3D turbulence structure in compound open-channel flows. Our discriminator PIV/PTV was applied successfully to sediment-laden open-channel flows and revealed the fluid/particle interaction and the relationship between coherent structures and sediment concentration. Finally, we conducted simultaneous measurements of velocity and dye concentration with a combination of PIV and LIF in vegetated open-channel flow, which enables us to examine turbulent scalar flux of a passive contaminant.     

High‐pixel‐rate grating‐light‐valve laser projector

Abstract— A high‐pixel‐rate, high‐contrast (30,000:1) wide‐color‐gamut grating‐light‐valve laser projector is reported. A new optical engine enabling high‐frame‐rate (240 Hz) scan projection is employed. Panoramic wide‐angle‐scan projection with a 64:9 aspect ratio was also developed. Speckle noise is eliminated using a simple but highly efficient technique. The optical throughput efficiency of the grating‐light‐valve laser projector is reviewed.     

Robust control method for the inverted pendulum system with structured uncertainty caused by measurement error

In this article, we propose a design method for an inverted pendulum system with a structured uncertainty. We consider that such an uncertainty is caused by a measurement error in the rotation angle of the pendulum and effects on the system structure that cannot be included in the nominal elements. For the uncertain system obtained, we apply an integral tracking control and the guaranteed cost control to design a robust, stable, tracking control system. Finally, we show the effectiveness of our method through a numerical example.     

The effect of small dose of topiroxostat on serum uric acid in patients receiving hemodialysis

Introduction : Topiroxostat, a recently developed xanthine oxidase inhibitor, is expected to have fewer adverse effects than allopurinol because it has different mechanism of action from alloprinol. However, its dosage, usage and safety have not been established in patients with impaired renal function or those undergoing dialysis at the development since no studies was conducted in these patients. Methods : Cross over clinical trial using 3 months of allopurinol and topiroxostat on 27 maintain Japanese HD patients were carried out. The effects on oxidative stress status of both drugs were also evaluated by measuring oxidation reduction potential. Findings : Twenty‐five of twenty‐seven patients completed study. The mean serum uric acid levels in the topiroxostat‐treated arm was significantly lower than it in the allopurinol‐treated arm time‐dependently (P < 0.0001). Corrected oxidative stress ratio defined as biological antioxidant potential/diacron reactive oxygen metabolites was significantly increased in topiroxostat‐arm (*P = 0.0035), but not in allopurinol‐arm (P = 0.1429). No significant difference was seen in diacron reactive oxygen metabolites, biological antioxidant potential, static oxidation‐reduction potential, and capacity oxidation‐reduction potential between pre and post treatment of both drugs. Discussion : It is suggested that a low dose of topiroxostat decreased serum uric acid sufficiently to maintain it below 7.0 mg/dL in patients receiving hemodialysis.     

Moiré‐reduction methods for integral videography autostereoscopic display with color‐filter LCD

Abstract— Moiré‐reduction methods for integral videography displays are proposed. Integral videography is based on the principles of integral photography and extended real‐time video processing. There are two moiré‐reduction methods that can be used for integral videography displays that have a lens array and a liquid‐crystal display. The first is color moiré, and the second is intensity moiré. To reduce color moiré, an optimized color‐filter layout in the liquid‐crystal display was used. To reduce intensity moiré, a defocusing method was used. Adesign of a viewing area for the integral videography display is also presented. To control the viewing area, the lens pitch and the shape of the integral videography elemental image was changed. A 5‐in. integral videography display was implemented by using the proposed methods, and an integral videography display was evaluated.     

Bottom-up pyramid cellular acceptors with three-dimensional layers

In 1997, C.R. Dyer and A. Rosenfeld introduced an acceptor on a two-dimensional pattern (or tape), called the pyramid cellular acceptor, and demonstrated that many useful recognition tasks are executed by pyramid cellular acceptors in time proportional to the logarithm of the diameter of the input. They also introduced a bottom-up pyramid cellular acceptor which is a restricted version of the pyramid cellular acceptor, and proposed some interesting open problems of the bottom-up pyramid cellular acceptors. On the other hand, we think that the study of threedimensional automata has been meaningful as the computational model of three-dimensional information processing such as computer vision, robotics, and so forth. In this paper, we investigate about bottom-up pyramid cellular acceptors with three-dimensional layers, and show their some accepting powers. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008