Fabrication and characterization of magnetic cotton yarns for textile applications

Cotton yarns covered with hard (barium hexaferrite – BaFe), and soft (Black Toner 6745 CP-313) magnetic particles are investigated for their application in the field of functional textile. Our results reveal a rather consistent dependence of the magnetic yarn properties on the fabrication parameters (nature of the magnetic powder, composition of the coating solution, etc.). The magnetic properties (residual magnetism and coercive field intensity) of the yarns are increasing with the magnetic powder content in the coating solution. However, this is at some point leading to the degradation of some yarn properties, e.g. elasticity. Bending tests revealed that several factors improve the bending behavior of the yarns and reduce cracks. For example, a higher number of cracks were exhibited by the hard magnetic yarns compared to the soft ones. The presence of polyurethane in the coating solution leads to no cracks on the surface of hard magnetic yarns or a small number in case of soft magnetic yarns. The tensile properties of the magnetic yarns are increasing with increasing magnetic powder content. Over a certain mass percentage (45% for BaFe and 30% for CP-313), the magnetic yarns tensile strength and elongation become lower than those of the support yarn.     

Three-Body Excitations in Fock-Space Coupled-Cluster: Fourth Order Perturbation Correction to Electron Affinity and Its Relation to Bondonic Formalism

In this paper, we present a formulation of highly correlated Fock-space multi-reference coupled-cluster (FSMRCC) methods, including approximate triples on top of the FSMRCC with singles and doubles, which correct the electron affinities by at least at third and up to the fourth order in perturbation. We discuss various partial fourth-order schemes, which are reliable and yet computationally more efficient than the full fourth-order triples scheme. The third-order scheme is called MRCCSD+T^*(3). We present two approximate fourth-order schemes, MRCCSD+T^*−a(4) and MRCCSD+T^*(4). The results that are presented allow one to choose an appropriate fourth-order scheme, which is less expensive and right for the problem. All these schemes are based on the effective Hamiltonian scheme, and provide a direct calculation of the vertical electron affinities. We apply these schemes to a prototype Li₂ molecule, using four different basis sets, as well as BeO and CH⁺. We have calculated the vertical electron affinities of Li₂ at the geometry of the neutral Li₂ molecule. We also present the vertical ionization potentials of the Li₂ anion at the geometry of the anion ground state. We have also shown how to calculate adiabatic electron affinity, though in that case we lose the advantages of direct calculation. BeO has been examined in two basis sets. For CH⁺, four different basis sets have been used. We have presented the partial fourth-order schemes to the EA in all the basis sets. The results are analyzed to illustrate the importance of triples, as well as highlight computationally efficient partial fourth-order schemes. The choice of the basis set on the electron affinity calculation is also emphasized. Comparisons with available experimental and theoretical results are presented. The general fourth-order schemes, which are conceptually equivalent with the Fock-space multi-reference coupled-cluster singles, doubles, and triplets (MRCCSD+T) methods, based on bondonic formalism, are also presented here in a composed way, for quantum electronic affinity.     

Oscillatory behavior of the magnetic properties of Nd–Fe–B films with Mo and Mo–Cu additions

A series of Ta/NdFeB/Ta thin films with Mo and Mo–Cu additions embedded by alloying and by stratification have been prepared by r.f. sputtering. The influence of additions, their embedding mode, and annealing temperature on the structural and magnetic behavior of Ta/NdFeB/Ta thin films is presented. The use of additions of Mo and Mo–Cu leads to refined grain structure and improvement in the hard magnetic characteristics of Ta/NdFeB/Ta thin films. The Ta/[NdFeBMo(540 nm)/Ta films and Ta/[NdFeB(180 nm)/MoCu(dnm)] × n/Ta multilayer films present enhanced coercivities and M_r/M_s ratios in comparison with the Ta/NdFeB(540 nm)/Ta films. The stratification of Ta/NdFeB/Ta thin films with Mo–Cu interlayers leads to an oscillatory behavior of hard magnetic characteristics of the Ta/[NdFeB(180 nm)/MoCu(dnm)] × n/Ta multilayer films, when the thickness, d, of Mo–Cu interlayers varies by increments of 1 nm. When the thickness of Mo–Cu interlayers varies by increments of 2 nm the oscillatory behavior of the magnetic characteristics is not revealed. For a thickness of the Mo–Cu interlayer of 3 nm in the Ta/[NdFeB(180 nm)/MoCu(3 nm)] × 3/Ta thin films annealed at 650 °C, the c-axis of part of the hard magnetic Nd₂Fe₁₄B grains is oriented out-of-plane.     

Structural properties of silver doped hydroxyapatite and their biocompatibility

The aim of this study was to obtain a novel hydroxyapatite-based material with high biocompatibility. The structural properties of the samples were well characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray Photoelectron Spectroscopy (XPS). The X-ray diffraction studies revealed the characteristic peaks of hydroxyapatite in each sample. Other phases or impurities were not observed. The scanning electron microscopy observations suggest that the doping components have no influence on the surface morphology of the samples, which reveals a homogeneous aspect of the synthesized particles for all samples. The presence of calcium (Ca), phosphor (P), oxygen (O) and silver (Ag) in the Ag:HAp is confirmed by energy dispersive X-ray (EDAX) and X-ray Photoelectron Spectroscopy analyses. Nanocrystalline silver doped HAp stimulated viability and potentiated the activation of murine macrophages.     

Thermoelectric La-doped SrTiO3 epitaxial layers with single-crystal quality: from nano to micrometers

Abstract

High-quality thermoelectric La_0.2Sr_0.8TiO₃ (LSTO) films, with thicknesses ranging from 20 nm to 0.7 μm, have been epitaxially grown on SrTiO₃(001) substrates by enhanced solid-source oxide molecular-beam epitaxy. All films are atomically flat (with rms roughness < 0.2 nm), with low mosaicity (<0.1°), and present very low electrical resistivity (<5 × 10^?4 Ω cm at room temperature), one order of magnitude lower than standard commercial Nb-doped SrTiO₃ single-crystalline substrate. The conservation of transport properties within this thickness range has been confirmed by thermoelectric measurements where Seebeck coefficients of approximately –60 μV/K have been recorded for all films. These LSTO films can be integrated on Si for non-volatile memory structures or opto-microelectronic devices, functioning as transparent conductors or thermoelectric elements.     

Investigation of Electrochemical Properties of Carbon Nanofibers Prepared by CCVD Method

Carbon nanofibers, with diameters between 80 and 290 nm and specific area of 242 m²g^?1, have been prepared by the catalytic chemical vapor deposition method. After preparation, the powder was mixed with silicon oil in order to create a paste electrode. The electrochemical behavior of this type of electrode was investigated by cyclic voltammetry, using a solution of 10^?3 M ferrocenecarboxylic acid as mediator. The redox process is quasi-reversible, and it involves the transfer of electrons between Fe(II) and Fe(III).

The same mediator was used for the construction of a second-generation glucose biosensor. The mediator was co-immobilized with the enzyme in the carbon nanofibers paste. The sensor linearly responded to glucose, in the concentration range of 1.7 to 7 mM. A time of around 30 seconds was required to reach 95% of the maximum steady-state current.

Also, the oxidation of calf thymus DNA at the carbon nanofiber paste electrode was investigated by differential pulse voltammetry (DPV). A clear signal, due to guanine oxidation, was obtained in the case of single-stranded DNA.     

Vacuum-processed polyethylene as a dielectric for low operating voltage organic field effect transistors

We report on the fabrication and performance of vacuum-processed organic field effect transistors utilizing evaporated low-density polyethylene (LD-PE) as a dielectric layer. With C₆₀ as the organic semiconductor, we demonstrate low operating voltage transistors with field effect mobilities in excess of 4 cm²/Vs. Devices with pentacene showed a mobility of 0.16 cm²/Vs. Devices using tyrian Purple as semiconductor show low-voltage ambipolar operation with equal electron and hole mobilities of ～0.3 cm²/Vs. These devices demonstrate low hysteresis and operational stability over at least several months. Grazing-angle infrared spectroscopy of evaporated thin films shows that the structure of the polyethylene is similar to solution-cast films. We report also on the morphological and dielectric properties of these films. Our experiments demonstrate that polyethylene is a stable dielectric supporting both hole and electron channels.     

Intrinsically Ductile Failure in a Nanocrystalline Beta Titanium Alloy

A nanocrystalline bcc Ti_67.4Nb_24.6Zr₅Sn₃ alloy is shown to fracture in an intrinsically ductile manner with exceptionally large dimples (up to 10 µm) which are two orders of magnitude greater than the grain size (≈ 40 nm). This large plasticity length scale is attributed to a combination of low shear modulus (≈ 27 GPa), high Poisson's ratio (≈ 0.4) and ultrahigh strength (UTS ≈ 1.1 GPa), close to the ideal shear stress, which facilitates ideal shear deformation to promote transgranular shear.     

Influence of the Carbo-Chromization Process on the Microstructural,Hardness, and Corrosion Properties of 316L Sintered Stainless Steel

We report on the changes on the microstructural, hardness, and corrosion properties induced by carbo-chromization of 316L stainless steel prepared by Spark Plasma Sintering technique. The thermo-chemical treatments have been performed using pack cementation. The carburizing and chromization were carried out between 1153 K (880 °C)/4 h to 1253 K (980 °C)/12 h and 1223 K (950 °C)/6 h to 1273 K (1000 °C)/12 h in a solid powder mixture of charcoal/BaCO₃ and ferrochromium/alumina/NH₄Cl, respectively. The obtained layers were investigated using X-ray and electron diffraction, optical and scanning electron microscopies, Vickers micro-hardness, and potentiodynamic measurements. The thickness of the carbo-chromized layer ranges between 300 and 500 μm. Besides the host γ-phase, the layers are mainly constituted of carbides (Fe₇C₃, Cr₂₃C₆, Cr₇C₃, and Fe₃C) and traces of α′-martensite. The average hardness values decrease smoothly from 650 HV at the sample surface down to 200 HV at the center of the sample. The potentiodynamic tests revealed that the carbo-chromized samples have smaller corrosion resistance with respect to the untreated material. For strong chromization regimes, the corrosion rate is increased by a factor of four with respect to that of the untreated material, while the micro-hardness of the layer is three times larger. Such materials are suited to be used in environments where good corrosion resistance and wear properties are required.