The onset of Taylor-Görtler vortices in impulsively decelerating swirl flow

The onset of hydrodynamical instability induced by impulsive spin-down to rest in a cylinder containing a Newtonian fluid is analyzed by using propagation theory. It is well-known that the primary transient swirl flow is laminar, but with initial high velocities secondary motion sets in at a certain time. The dimensionless critical time Τ_c to mark the onset of instability is presented here as a function of the Reynolds number Re. Available experimental data indicate that for large Re deviation of the velocity profiles from their momentum diffusion occurs starting from a certain time Τ≈4Τ_c. This means that secondary motion is detected at this characteristic time. It seems evident that during Τ_c⪯Τ⪯4Τ_c, secondary motion is relatively very weak and the primary diffusive momentum transfer is dominant.     

Solid state interfacial reactions in electrodeposited Ni/Sn couples

Ni/Sn couples,prepared by sequentially electroplating Ni layers and Sn layers on metallized Si wafers,were employed to study the mierostructures and growth kinetics of Ni-Sn intermediate phases,when the Ni/Sn couples were aged at room temperature or annealed at temperatures from 150 to 225℃for various times.The results show that the NiSn phase and Ni_3Sn_4 phase are formed,respectively,in the aged couples and annealed couples.The Ni_3Sn_4 layer is continuously distributed between the Ni and Sn sides in t...     

实验动物在血液制品中的应用

目的：阐述实验动物在血液制品生产质量控制过程中应用的重要性。方法：按《中华人民共和国药典》2005年版三部要求及相关项目的技术规范进行血液制品质量控制。结果：血浆数量150吨,可同时生产以下品种的产品,人血白蛋白共30批次,总瓶数约40万瓶（折10g）;免疫球蛋白类：共30批次,总瓶数约30万瓶（折2.5g）;人纤维蛋白原：共30批次,总瓶数约15万瓶（折0.5g）;人凝血酶原复合物：共30批次,总瓶数约12万瓶（折300IU）;人凝血因子Ⅷ：共30批次,总瓶数约10万瓶（折200IU）。需使用家兔870只、豚鼠300只小鼠750只。结论：实验动物应用于血液制品生产质量控制发挥了非常重要的作用。     

Synthesis and luminescence properties of Pr3+ doped CaxBa1?xTiO3 (0.3?x<1) fine particles

Ca _x Ba_1−x TiO₃ (CBT) fine particles doped with red luminescence center of Pr³⁺ ions (Pr: CBT) were successfully synthesized by salt assisted spray pyrolysis (SASP) process. Scanning electronic microscope (SEM) and laser scattering analysis demonstrate that salt can be removed from the surface of particles by washing with Milli-Q water and the particles can be further separated by ball-milling to get well-dispersed Pr³⁺ ions doped CBT fine particles. The luminescence properties, such as photoluminescence (PL) and mechanoluminescence (ML), of as-synthesized Pr: CBT particles were investigated. For Pr: CBT fine particles with different Ca molar ratios, all the samples show one emission at 612 nm, with increasing Ca molar ratio, PL intensity of Pr: CBT fine particles become stronger and stronger. When pressure was loaded on the Pr: CBT pellet, mechanoluminescence(ML) emission was measured. The results show that the ML intensity is proportional to the applied pressure.     

Cycling hardening and serration yielding of Fe-Ni-Cr alloy at high temperature under out-phase TMF

Behaviour of hardening and serration yield of a Fe-Ni-Cr alloy under isothermal cycling (ISC) and out-phase TMF was studied on the basis of varied hysteresis loops. Cycling hardening and serrated yielding for ISC depend on the temperature and the total strain range, stronger hardening with serrated yielding at higher strain range under ISC at 600 °C, but no hardening and serrated yielding occurred under ISC at 800 °C. Stronger hardening with stress serration occurred at the thermal path going to the lowest temperature, no stress serration occurred at the highest temperature under the out-phase. The hardening also depends on the total strain range, higher total strain range with lower cycling temperature resulted in a stronger hardening and remarkable serration yielding behavior. Weaker hardening without serrated yielding occurred at near 800 °C may due to an obvious cycling stress drop under out-phase TMF. Change in the shape of the hysteresis loops also expresses the degree of the damage of the tested alloy under out-phase and ISC.     

考虑过程能力和成本的刀具策略研究

为了提高定期维修的刀具所加工的产品质量,减少停机时间和生产成本.考虑生产过程中工件尺寸的残差是时间的函数,利用Glejser检验方法,拟合工件尺寸残差符合的递增型异方差模型,提出了刀具磨损过程的过程能力指数计算方法;使用Bernstein概率密度函数描述刀具寿命和刀具磨损过程的一般特征,在每一个维修周期内均满足顾客要求的最小过程能力指数基础上,考虑质量损失、换刀成本、由刀具的突然失效引发的惩罚成本及维修刀具所需的成本,将过程能力与成本相结合,提出了用于确定最佳刀具初始状态和维修周期的模型.该模型为实际生产提供了一种离线的刀具管理方法.     

制造任务分解与制造单元级资源配置协同优化

针对网络化制造环境下制造任务分解与资源配置脱节的问题,提出了制造任务逐层分解与制造单元级资源配置协同优化的方法,建立了协同优化流程.在对制造任务特点进行分析的基础上,建立了制造任务模型和制造单元资源模型,建立了多目标优化模型和目标的综合评价体系,利用在遗传算法求解搜索过程中所获得的动态信息进行综合评价,并随着求解搜索过程的深入对变异幅度进行调整,以达到全局优化和加快收敛速度的目的.最后以实例验证了该方法的可行性与有效性.     

含给电子Z-N催化剂催化乙烯/1-丁烯共聚的研究

研究了两种含有给电子体分别为对硝基苯胺、乙二醇二甲醚的Ziegler-Natta催化剂催化乙烯与1-丁烯高压的共聚反应性能,主要考察了反应条件对聚合活性、聚合物物理性质的影响,同时采用红外光谱法测定了聚合物的支化度.研究表明,给电子体为乙二醇二甲醚的催化剂催化活性高于对硝基苯胺.反应条件如反应压力、温度、铝钛比对聚合活性、丁烯的插入率以及聚合物性质都有明显影响.高的反应压力有利于1-丁烯插入和聚合物堆密度的提高;反应温度在50℃时的聚合活性最大,聚合物的支化度较高,聚合物熔点较低;铝钛比为500时聚合活性高于低铝钛比的聚合活性.