Unsteady extinction mechanism of nonpremixed flame interacting with a vortex

The extinction mechanism of a CH₄/N₂-air counterflow nonpremixed flame interacting with a single vortex was numerically studied. An augmented reduced mechanism was used to treat the CH₄ oxidation reactions. The contribution of each term in the energy and the OH species equations were evaluated to investigate the unsteady extinction mechanism of nonpremixed flame. The flame temperature began to decrease due to the convection heat loss when the flame interacted with a vortex. The investigation of the radical behavior during the flame-vortex interaction process also provided useful information on the unsteady extinction mechanism. The OH radical concentration could be used as a good tracer of the state of the unsteady extinction of nonpremixed flame. The reduction mechanism of OH concentration was confirmed by analyzing the contribution of each term in the OH species equation. At initial stage of flame-vortex interaction, the OH production and consumption rates increased gradually, while the OH concentration was kept nearly constant. Near the extinction limit, the OH production rate decreased rapidly due to the low flame temperature, and the balance between the OH production and OH consumption by diffusion could not be maintained. The unsteady nonpremixed flame interacting with a vortex under the conditions of regime (V) shown in the spectral combustion diagram [Thévenin, D., Renard, P.H., Fiechtner, G.J., Gord, J.R., Rolon, J.C., 2000. Regimes of non-premixed flame-vortex interactions. Proceedings of the Combustion Institute 28, 2101-2108.] was finally extinguished due to low reactivity, which was induced by the low flame temperature.     

Diffusion of additives and plasticizers in poly(vinyl chloride): 4. A programmed temperature technique for the determination of the diffusion parameters of three dialkylphthalates

A programmed temperature technique has been developed for the measurement of the self-diffusion coefficients of additives in polymers. This has been applied to the diffusion of three dialkylphthalate plasticizers in poly(vinyl chloride). Values of the self-diffusion coefficients and the calculated activation energies obtained in this way have been compared with values previously obtained from measurements at constant temperature. It has been shown that the programmed temperature technique gives a very rapid method for the estimation of the activation energy of self-diffusion.     

Process optimization of sweet potato pulp‐based biodegradable plastics using response surface methodology

Biodegradable plastics were produced from sweet potato pulp (SPP) and cationic starch (CS) or chitosan composite (CC) by compression molding and their mechanical properties were tested. A universal testing machine, Rockwell hardness tester, and Izod impact tester were used for testing the mechanical properties (flexural strength, Rockwell hardness, and Izod strength) of the plastics. A central composite second‐order design was used to study the effects of temperature, time, and moisture content on the flexural strength, Rockwell hardness, and Izod strength of SPP/CS and SPP/CC blended plastics. The flexural strength, Rockwell hardness, and Izod strength of SPP‐based plastics was 101.1–305.9 kg/cm², R29.0–R96.7, and 0.6–3.0 kg cm cm^?2, respectively. Regression analysis predicted the optimal mechanical properties (flexural strength, Rockwell hardness, and Izod strength) to be attained with a 150–160°C temperature, 15–20‐min reaction time, and 20–23% moisture content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 423–434, 2002     

Dispersion of flexible polymer chains in confined geometries

Molecular model approach has been used to predict the dispersion characteristics of flexible polymer chains in confined geometries. The analysis ranges from the early stage dispersion to the steady Taylor dispersion of the simple linear dumbbell model polymer chains. For the early stasje dispersion the ray method was applied; an Aris type moments rnothod was useful for the Taylor dispersion. Two parallel plates were chosen as a confining geometry and the specific initial condition of a point source in the midway of the gap was chosen for simplicity. It was found that the qualitative difference in dispersion properties of deformable polymer chains starts from the early stage compared with those of single Brownian particles. And it turns out that one parameter, which is similar to the relative spacing of the dumbbell to the gap of confining geometries, is useful to see the dispersion characteristics of the dumbbells.     

Processabilities and mechanical properties of surlyn-treated starch/LDPE blends

The esterification of the hydroxyl group of starch with DuPont Surlyn was considered as pretreatment method of starch before blending with polyolefins. In treating starch with Surlyn, two different raction conditions were taken to optimize reaction conditions. First, the esterification reaction was carried out in 110°C xylene with oleic acid as a catalyst. Second, the reaction out in a 90°C mixture of deionized water and xylene with ceric ammonium nitrate(CAN) as an initiator. Starch granules would be swollen above the gelatinization temperature in water. In both cases starch was midified by Surlyn to have good compatibility with low-density polyethylene (LDPE). The mechanical and theological properties were examined for blends of the treated starch and LDPE. This system may be one of the biodegradable polymer blends that sufficiently retain properties as a packaging film.     

SEQUENTIAL LOOP CLOSING IDENTIFICATION OF MULTIVARIABLE PROCESSES USING THE BIASED RELAY FEEDBACK METHOD

Each controller in multiloop control systems for multivariable processes can be tuned sequentially with the ultimate information for the paired input and output while former loops have been closed, and hence, single-input single-output autotuning methods can be applied. In this sequential autotuning for multiloop control systems, several iterations are usually required for better control performances. Especially when pairings are undesirable, the autotuning sequences should be repeated with correct pairings, which result in long field experiments. Here, to avoid this drawback, a simple method to identify process models while loops are being sequentially tuned is proposed. The identified models can be used to correct pairings of multiloop control systems and to improve tuning performances without several field iterations. In addition, they can be used to obtain model-based control systems such as decoupling control systems.     

Catalytic Combustion of Methane over Rare Earth Stannate Pyrochlore

Well-defined Ln₂Sn₂O₇ powders (Ln = La, Sm and Gd) with a phase-pure pyrochlore structure were synthesized by hydrothermal reaction. The catalytic activities of Ln₂Sn₂O₇ powders for methane combustion were measured. Methane oxidation started at 500 °C and increased with oxidation temperature. Catalytic methane combustion is strongly influenced by the presence of oxygen vacancies that form by breaking Sn–O lattice bonds as the temperature increases. Addition of manganese to the rare earth pyrochlores improved methane oxidation activity. Manganese-doped samarium stannate pyrochlore (Sm₂Sn_1.8Mn_0.2O₇) shows highest the catalytic activity. Light-off and complete oxidation temperatures were measured at about 400 and 650 °C, respectively.     

Sol-Gel Alumina Coating for Improved Cyclic Oxidation Resistance of Silicon Nitride

A 25 nm thick α-alumina layer was deposited on a turbine-grade silicon nitride by sol-gel dip coating and subsequent heat treatment in air at 1200°C. This layer had a nanometer grain structure. Silicon nitride protected by this thin layer showed a significant improvement in oxidation resistance over its uncoated counterpart after 200 cyclic exposures in air at 1250°C. The oxide layer grown on the coated silicon nitride also exhibited superior surface morphology, compared with the uncoated silicon nitride.     

Effect of solution properties on nanofibrous structure of electrospun poly(lactic‐co‐glycolic acid)

Electrospinning of poly(lactic‐co‐glycolic acid) (PLGA) in chloroform or 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP) was investigated, focusing on its solution parameters, to develop nonwoven biodegradable nanofibrous structures for tissue engineering. PLGA nanofibers were obtained by electrospinning of 15 wt % PLGA solution and the resulting average fiber diameters were varied with the range of 270–760 nm, depending on solution property. When small amounts of benzyl triethylammonium chloride (BTEAC) was added to the PLGA/chloroform solution, the average diameter was decreased from 760 to 450 nm and the fibers were densely amounted in a straight shape. In addition, the average fiber diameter (270 nm) of nanofibers electrospun from polar HFIP solvent was much smaller than that (760 nm) of nanofibers electrospun from nonpolar chloroform solvent. Therefore, it could be concluded that conductivity or dielectric constant of the PLGA solution was a major parameter affecting the morphology and diameter of the electrospun PLGA fibers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1214–1221, 2006     

Effects of Purified Persimmon Tannin and Tannic Acid on Survival and Reproduction of Bean Bug, Riptortus clavatus

We evaluated the effects of tannic acid and purified perrsimmon tannin on survival and reproduction of bean bugs, Riptortus clavatus.Feeding behavior of R. clavatus was also examined on sweet (cv. Fuyu) and astringent (cv. Chongdosi) persimmon fruits. Soluble tannin in sweet persimmon fruits decreased from 3% in early June to 0.5% in late September, but it increased from 2 to 8% during the same period in astringent persimmon fruits. More bugs visited sweet than astringent persimmon. Numbers of piercing/sucking spots were higher on sweet than on astringent persimmon. When fed 1 and 3% solutions of persimmon tannin, adult bugs ingested only 64.1 and 9.5% of the amount of water ingested by those offered the control (distilled water). Amounts of persimmon tannin ingested by the adult bugs were 6.5 and 2.8 times higher at 1 and 3% tannin solutions compared to a 0.1% solution. Persimmon tannin exerted negative effects on survival and reproduction of R. clavatus at higher concentrations (1 and 3% solutions). Feeding of R. clavatus adults decreased with increasing tannin concentrations. When results from both sexes were pooled, 50% mortality was achieved at 11 and 4 days after treatment with the 1 and 3% tannin solutions, respectively. Reproduction decreased with 1% tannin, and no eggs were produced with 3% tannin solution. Tannic acid was similar in its effects on R. clavatus. All nymphs died 14, 12, and 7 days after feeding on 0.1, 1, and 3% tannic acid, respectively. Adults were less sensitive than nymphs, and their survival was not affected by 0.1% tannic acid. However. 1 and 3% tannic acid solutions were fatal. Survivorship decreased to 50% at 11 and 6 days after supplying tannin solutions of 1 and 3% concentrations. Higher concentrations (1 and 3%) resulted in reduced reproduction, as was seen with persimmon tannin. Our data may explain why R. clavatus does not invade sweet persimmon orchards until late July, when concentrations of soluble tannin are low enough to allow them to feed.