Power management unit chip design for automobile active-matrix organic light-emitting diode display module

A power management unit (PMU) chip supplying dual panel supply voltage, which has a low electro-magnetic interference (EMI) characteristic and is favorable for miniaturization, is designed. A two-phase charge pump circuit using external pumping capacitor increases its pumping current and works out the charge-loss problem by using bulk-potential biasing circuit. A low-power start-up circuit is also proposed to reduce the power consumption of the band-gap reference voltage generator. And the ring oscillator used in the ELVSS power circuit is designed with logic devices by supplying the logic power supply to reduce the layout area. The PMU chip is designed with MagnaChip’s 0.25 μm high-voltage process. The driving currents of ELVDD and ELVSS are more than 50 mA when a SPICE simulation is done.     

Design of small-area multi-bit antifuse-type 1 kbit OTP memory

A multi-bit antifuse-type one-time programmable (OTP) memory is designed, which has a smaller area and a shorter programming time compared with the conventional single-bit antifuse-type OTP memory. While the conventional antifuse-type OTP memory can store a bit per cell, a proposed OTP memory can store two consecutive bits per cell through a data compression technique. The 1 kbit OTP memory designed with Magnachip 0.18 μm CMOS (complementary metal-oxide semiconductor) process is 34% smaller than the conventional single-bit antifuse-type OTP memory since the sizes of cell array and row decoder are reduced. And the programming time of the proposed OTP memory is nearly 50% smaller than that of the conventional counterpart since two consecutive bytes can be compressed and programmed into eight OTP cells at once. The layout area is 214 μm × 327 μm, and the read current is simulated to be 30.4 μA. Foundation item: Project supported by the 2nd Stage of Brain Korea; Project supported by the Korea Research Foundation     

Fabrication of a gradient refractive index preform using laminar shear mixing

A gradient refractive index rod was successfully prepared by a new fabrication method using laminar shear mixing, and a graded index polymer optical fiber that satisfied IEEE1394b was obtained from the method. To fabricate the gradient refractive index rod, a liquid monomer mixture with a relatively low refractive index was placed in a prepared cylindrical glass reactor and a transparent polymer rod with a higher refractive index was introduced at the center of the reactor. The reactor and the polymer rod were then rotated concurrently with a small rotating speed difference to generate a Couette flow in the liquid phase. The centrifugal force generated by rotation and the polymer diffusion into the liquid monomer mixture developed a graded concentration profile in a radial direction. The Couette flow could reduce the concentration fluctuation in a tangential direction. In addition, the graded index profile could be controlled by the copolymer composition of the rod and its diameter. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1100–1104, 2005     

Biodegradability of cellulose fabrics

Biodegradability of cellulose fabrics was evaluated by use of a soil burial test, an activated sewage sludge test, and an enzyme hydrolysis. Surface changes after biodegradation were observed by optical microscopy. From X‐ray diffraction analysis (XRD), changes in the crystallinities and the internal structures as a result of degradation were also investigated. It was shown that biodegradability decreased in the following order: rayon > cotton ? acetate. Rayon fibers, which have a low crystallinity and a low degree of orientation, showed the highest biodegradability in most cases. However, in spite of its low crystallinity, acetate fibers exhibited very low biodegradability, probably because of the presence of hydrophobic groups in its structure. On the other hand, linen showed an inconsistent behavior in that it had the highest biodegradability in the soil burial test, but a lower biodegradability than that of cotton in the activated sewage sludge test. XRD analysis revealed that there was a slight increase in the crystallinity of linen, cotton, and rayon fabrics at the initial stage, but a continuous decrease thereafter. From the correlation analysis, it was revealed that the biodegradability of cellulose fabrics was closely related to the moisture regain of the fibers, which reflects the hydrophilicity and internal structure of the fibers at the same time. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 248–253, 2004     

Professional colour communicator-the definitive colour selector

There are several systems available for the communication and selection of colours. A new system, allying precise colour differences to dye recipes, is the Professional Colour Communicator. James and Kevin Park tell us more.     

Preparation of alginate/poly(N‐isopropylacrylamide) semi‐interpenetrating and fully interpenetrating polymer network hydrogels with γ‐ray irradiation and their swelling behaviors

Semi‐interpenetrating polymer network (semi‐IPN) and fully interpenetrating polymer network (full‐IPN) hydrogels composed of alginate and poly(N‐isopropylacrylamide) were prepared with γ‐ray irradiation. The semi‐IPN hydrogels were prepared through the irradiation of a mixed solution composed of alginate and N‐isopropylacrylamide (NIPAAm) monomer to simultaneously achieve the polymerization and self‐crosslinking of NIPAAm. The full‐IPN hydrogels were formed through the immersion of the semi‐IPN film in a calcium‐ion solution. The results for the swelling and deswelling behaviors showed that the swelling ratio of semi‐IPN hydrogels was higher than that of full‐IPN hydrogels. A semi‐IPN hydrogel containing more alginate exhibited relatively rapid swelling and deswelling rates, whereas a full‐IPN hydrogel showed an adverse tendency. All the hydrogels with NIPAAm exhibited a change in the swelling ratio around 30–40°C, and full‐IPN hydrogels showed more sensitive and reversible behavior than semi‐IPN hydrogels under a stepwise stimulus. In addition, the swelling ratio of the hydrogels continuously increased with the pH values, and the swelling processes were proven to be repeatable with pH changes. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4439–4446, 2006     

Dissipative structures of autocatalytic reactions in tubular flow reactors

Dissipative structures of autocatalytic reactions with initially uniform concentrations are studied in tubular flow reactors. A unique steady state exists in a continuous stirred tank reactor. Linear stability analysis predicts either a stable node, a focus or an unstable saddle-focus. Sustained oscillations around the unstable focus can occur for high values of Damköhler number. In distributed parameter systems, travelling, standing or complex oscillatory waves are detected. For low values of Damköhler number, travelling waves with pseudo-constant patterns are observed. With intermediate values of Damköhler number, single or multiple standing waves are obtained. The temporal behavior indicates also the appearance of retriggering or echo waves. For high values of Damköhler number, both single peak and complex multipeak oscillations are found. In the cell model, both regular oscillations near the inlet and chaotic behavior downstream are observed. In the dispersion model, higher Peclet numbers eliminate the oscillations. The spatial profile shows a train of pulsating waves for the discret model and a single pulsating or solitary wave for the continuous model.     

Continuous ethanol production from wood hydrolysate by chemostat and total cell retention culture

Chemostat and total cell retention cultures with internal filter system ofSaecharomyc.es cerevisiae H1-7 were carried out to produce ethanol from wood hydrolysate. Maximum ethanol productivity obtained in a chemostat with the aeration rate of 1 vvm was 3.79 g/(L·h). This was 20% higher than that in a chemostat without aeration. However, the substrate was not completely consumed at the dilution rate with the maximum productivity. The realistic productivity, which has higher than 99% conversion rate of substrate, was. 2.95 g/(L·h). The maximum productivity in the total cell retention culture was 6.65 g/(L·h) at the dilution rate of 0.19 h¹ and the residual glucose concentration was negligible.     

Fundamental foaming mechanisms governing the volume expansion of extruded polypropylene foams

This article describes the fundamental foaming mechanisms that governed the volume expansion behavior of extruded polypropylene (PP) foams. A careful analysis of extended experimental results indicated that the final volume expansion ratio of the extruded PP foams blown with butane was governed by either the loss of the blowing agent or the crystallization of the polymer matrix. A charge coupling device (CCD) camera was installed at the die exit to carefully monitor the shape of the extruded PP foams. The CCD images were analyzed to illustrate both mechanisms, gas loss and crystallization, during foaming at various temperatures, and the maximum expansion ratio was achieved when the governing mechanism was changed from one to the other. In general, the gas loss mode was dominant at high temperatures and the crystallization mode was dominant at low temperatures. When the gas loss mode was dominant, the volume expansion ratio increased with decreasing temperature because of the reduced amount of gas lost. By contrast, when the crystallization mode was dominant, the expansion ratio increased with increasing temperature because of the delayed solidification of the polymer. The processing window variation with the butane concentration, the change in the temperature ranges for the two governing modes, and the sensitivity of melt temperature variations to the volume expansion ratio are discussed in detail on the basis of the obtained experimental results for both branched and linear PP materials. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2661–2668, 2004     

Energetic surface heterogeneity of nanocrystalline TiO<Subscript>2</Subscript> films for dye-sensitized solar cells

Dye sensitized solar cells (DSSCs) have been receiving significant attention because they have many advantages compared to conventional organic solar cells. It has been known that the photovoltaic characteristics of DSSC are highly dependent on the adsorption properties of dyes on TiO₂ films. To analyze the surface heterogeneity of TiO₂ surfaces, single-phase anatase nanocrystallite titanium films were prepared by sol-gel method using the hydrolysis reaction of titanium tetraisopropoxide under acidic condition and characterized by XRD, FE-SEM and BET analysis. The adsorption energy distribution functions were calculated by the generalized nonlinear regularization method. It was found that the shape and the intensity of the adsorption energy distribution curve determined were highly related with the physical properties (i.e., geometrical heterogeneity) and chemical characteristics (i.e., energetic heterogeneity) of nanocrystalline TiO₂ for DSSC.