化工重大技术装备工作"十五"的成绩与"十一五"的任务

重大技术装备的制造水平是一个国家综合实力的直接体现,因此从上个世纪八十年代初开始,历届国务院领导人均兼任国家重大技术装备领导小组组长,通过推进重大技术装备的发展,促进     

汉白玉废料制备球形纳米碳酸钙的研究

将汉白玉废料通过高温煅烧分解得到氧化钙,再用氯化铵循环液溶解氧化钙制得碱性氯化钙溶液,除去其中的Mg、Fe等杂质得到氯化钙精制溶液,利用化学方法合成得到碳酸钙粉体.用X射线衍射(XRD)、扫描电镜(SEM)及激光粒度分析仪、白度仪对碳酸钙产品的晶相组成、形貌、粒度分布、白度及化学组成进行了分析,所得产品为纯度达98.5%以上、白度达97%以上、平均粒度为80nm左右的球形纳米级碳酸钙.并对碳化反应速率及合成球形纳米碳酸钙的影响因素进行了分析.实验中循环使用NH4Cl,氨的排放量小,减少了环境污染.     

厌氧胶快速渗补技术在汽车发动机上的应用

将金属铜易与过氧化物发生氧化还原反应生成游离基的原理应用于厌氧胶，开发了针时金属零件表面微孔进行局部渗补的实用技术。在相关技术可靠性和工艺可行性得以论证的前提下。将局部渗补技术成功地应用于渗补发动机泄漏缸盖，减少了废品损失，取得了良好的经济效益。     

YAG：Ce Phosphors for WLED via Nano-Pesudoboehmite Sol-Gel Route

The sub-micron sized YAG ： Ce phosphors were synthesized via a modified sol-gel method by peptizing nano-pesudoboehmite particulate. It is found that YAG phase from the dried gel powders appears at 1000 ℃ then the pure YAG phase exists at a relatively lower sintering temperature of 1400 ℃. The smaller sizes of phosphors in the ranges of 1 - 3 μm are obtained due to the contribution of seeding effects of nano-sized alumina particles to strengthen each step of the processes. Both the excitation and emission spectra of photoluminescence of the phosphor obtained at 1400 ℃ meet well with the spectroscopic requirements of the WLED phosphors.     

A hexane solution deposition of SnS2 films from tetrabutyltin via a solvothermal route at moderate temperature

SnS₂ films have been deposited on glass and alumina plate substrates by the reactions between an organotin precursor [tetrabuyltin, (CH₂CH₂CH₂CH₃)₄Sn] and carbon disulfide in n-hexane at the temperature range 180-200 °C for 10-40 h. The reaction system was oxygen free and applied at a moderate temperature. The films so prepared were characterized by techniques of X-ray diffraction, Scanning electron microscopy, Raman and Mössbauer spectroscopies. The films deposited on glass as well as on alumina plate have an average thickness of 30 μm, but have different rose-like morphologies, which are influenced by both the anisotropic growths of crystals and the different substrate structures. Photoluminescence measurements show that the films have an emission peak at approximately 590 nm.     

Bioprocess applications of model-based estimation techniques

The last decade has seen the development of a number of approaches for estimating those variables which are difficult to measure on-line in industrial process situations. Whilst a range of techniques is available, a common element is the use of process knowledge in the form of a system model. In the case of bioprocess systems, although a large range of models has been presented in the literature, their use in estimation schemes on an industrial scale has been limited. A number of reasons can be identified for their low level of utilisation. Of particular significance is the uncertainty which exists in quantifying system performance and the process-model mismatch which inevitably results. The level of ‘pre-defined model’ uncertainty, together with the knowledge gained during the course of the fermentation, serves to dictate estimator structure. The paper considers a range of estimation strategies and contrasts, through industrial applications, their performance characteristics and utility.     

Using thermally stimulated currents to find defective capacitors

BaTiO₃ multilayer capacitors with a nominal capacitance of 3.5nF have been carefully measured using the thermally stimulated current (TSC) technique. When a 300V polarization voltage is applied at room temperature, a new TSC peak appeared in defective sample A after it has been immersed in water. No new peak was found in good-quality sample B after a similar treatment. The accelerated life test shows that sample A hasa much shorter life than sample B in terms of insulation resistance.     

精馏塔静态仿真：Ⅰ.静动态混合数学模型的应用

本文为了克服精馏塔静态仿真不易收敛和初值难以给定等难题，巧妙地利用隐含数值积分方法的特点，将稳态与动态数学模型耦合起来，用以求解高难度的非理想精馏塔静态仿真问题。所得静动态混俣模型大大提高了精馏塔静态仿真的鲁棒性，对于高度非理想精馏塔的仿真尤为有效。通过对某丙烯腈萃取精馏塔的静态仿真，充分证明了这种混合模型化方法的可行性。     

^125I,^131I诱发小鼠精子畸形发生率比较

本文选用 ICR 雄性小鼠,经腹腔分别注射不同剂量的~(125)I 及~(131)I,观察并比较它们对小鼠精子畸形发生率的影响及染毒后睾丸中放射性活度的变化。实验结果表明:(1)~(125)I 染毒后4—5周,0、185、370和555 kBq 各组精子畸形发生率分别为9.00‰、9.57‰、11.6‰及13.9‰;~(131)I 染毒后4—5周,上述各组精子畸形发生率分别为8.50‰、12.5‰、14.7‰和15.5‰;在相同注入量下,~(125)I 与~(131)I 诱发小鼠精子畸形发生率的差异各组均不显著(X~2检验,p>0.05)。(2)~(125)I、~(131)I 染毒后2h 至7天内,两者在睾丸中的放射性活度及变化规律相似,即在染毒后2h 达最高值,每克睾丸中~(125)I 和~(131)I 的放射性活度分别占初始注入量(370 kBq)的0.72％和0.50％,然后迅速下降,至一周时,仅分别占初始注入量的0.035％和0.011％。     

Designing circuits with partial scan

In this scan design methodology, only selected faults are targeted for detection. These faults are those not detected by the designer's functional vectors. The test generator decides exactly which flip-flops should be scanned using one of two methods. In the first method, all possible tests are generated for each target fault, and the set of tests requiring the fewest flip-flops is selected. In the second method, only one test is generated for each fault, and the use of flip-flops is avoided as much as possible during test generation. Examples of actual VLSI circuits show a savings of at least a 40% in full-scan overhead