IF钢冷轧及再结晶初期微观组织的TEM研究

采用透射电子显微镜对不同压下量和再结晶初期的IF钢样品进行了研究．结果表明：无论是在较小形变量下还是在较大形变量下，形变不均匀性是普遍存在的；冷变形程度不同，织构组分不同，TEM形貌也不同；在再结晶的最初期，冷轧的形变组织演变为近乎等轴的亚晶，优先形成{111}〈uvw〉取向的晶核，晶核逐渐吞并周围的形变基体而长大，最终形成再结晶γ-纤维织构．     

一种高精度的CMOS带隙基准电压源

设计了一种采用0.25 μm CMOS工艺的高精度带隙基准电压源.该电路结构新颖,性能优异,其温度系数可达3×10-6/℃,电源抑制比可达75 dB.还增加了提高电源抑制比电路、启动电路和省功耗电路,以保证电路工作点正常、性能优良,并使电路的静态功耗较小.     

Electrochemical C-V Characteristics and Photoluminescence of a-C∶N Films

Amorphous carbon (a-C) films and amorphous carbon films incorporating with the nitrogen (a-C∶N) were deposited on silicon substrates in a radio-frequency driven plasma enhanced chemical vapour deposition system, while the surface electrical properties of films were investigated by electrochemical capacitance-voltage measurements. It was examined the effect of the interface defects on the properties and deduced that the conducting type of a-C∶N films was n-type. Subsequently, a comparative studies of a-C and a-C∶N films were performed by photoluminescence spectra depending on the temperature. With the decrease of the temperature, the main band with peak energy of 2.48 eV in the a-C∶N films was more intense compared with the other three bands caused by amorphous C in the a-C films.     

石化企业分配制度改革初探

在明确中国石化集团公司收入分配制度改革的目标模式下,从健全和完善企业激励机制的角度,对炼化企业职工收入分配制度中工资和奖金的分配设计提出改进措施和建议。     

Optimal Layout of Displacement Measurements for Parameter Identification Process in Geomechanics

This paper focuses on designing the optimal layout of measurements for parameter identification problems in geomechanics, which are usually based on in situ displacements. The existence, uniqueness, and stability of the solution from the parameter identification process are thoroughly discussed. Based on these understandings of the problem, two algorithms are proposed as a means of automatically generating the optimal measurements. The validity of these algorithms is first proved by some academic examples, then these algorithms are applied to the Munich subway tunnel project. Good results are observed there.     

高碳铬铁电炉炉衬的损坏及维护

叙述了重钢公司几个高碳铬铁电炉使用全印度粉矿在冶炼过程中炉衬的损坏情况及其原因，提出了炉衬维护中应注意的几个方面。     

电接点压力表补水泵定压系统的应用

阐述了电接点压力表补水泵定压系统的一些应用问题 ,给出了电接点压力表定压点的上、下限计算公式 ,并提出了该系统补给水泵、补给水箱及安全阀的设计选型方法     

OSI参考模型与B—ISDN协议参考模型的比较

分析了ＯＳＩ参考模型和Ｂ－ＩＳＤＮ协议参考模型之间的关系，为Ｂ－ＩＳＤＮ与以ＯＳＩ为标准的数据网的互联打下了基础。     

悬沙中D〉0．06mm粗粒的粒析级配组成及其改正方法

本文首先简述Ｄ＞０．０６ｍｍ泥沙的粒析沉降特性及其粒径偏粗的原因。继之对悬沙中粒径大于０．０６ｍｍ的粒析级配组成机理，及级配组成不同对标准粒径Ｄｂ与粒析粒径ＤＬ关系的影响进行了详细研究。在以上研究工作的基础上，开展了Ｄｂ与ＤＬ的比较试验，得出了粗、中、细型悬沙的Ｄｂ～ＤＬ关系和对ＤＬ的改正方法。     

GLOBAL: A Design for Random Testability Algorithm

1MotivationsIncreasingdensityofVLSIchipsmakesthecostoftestingveryexpensive.Designfortestabilitycantemperthisproblemdrastically.Therearetwokindsofsolutions:(i)localsolutionl3'2]withlowcomputingcomplexity,whichcannotalwaysgetsatisfactoryresults;(ii)globa.lsolutionwithprohibitivecomputingcomplekityl1'5].T.H.Chen'andM.A.Breuer[1lpresentedanILPmodeltoplacetestpointsglobally.Becauseofitscomputingcomplealty,[1lcanonlydealwithsmallormediumscalecircuits.SCOAPisusedin[1],whichisnotaveryaccuratet…