Precise analysis of H, C, N, and O as dominant impurities in Cu films: complementary use of SIMS and GDMS

Secondary ion mass spectrometry (SIMS) and glow discharge mass spectrometry (GDMS) were used to determine the impurity concentrations of hydrogen, carbon, nitrogen, and oxygen elements in Cu films, and the results of SIMS and GDMS were carefully interpreted. The Cu films were deposited on Si (100) substrates at substrate bias voltages ranging from 0 V to −150 V using a non-mass separated ion beam deposition method. From the results of SIMS using a Cs⁻ ion beam, as a whole, many high intensity peaks were observed in the Cu films deposited without substrate bias voltage. From the quantitative GDMS results, these peaks were determined to be signals detected as a cluster state such as C_xH_x, O_xH_x, C_xO_xH_x. Therefore, using a combination of these dominant impurities, all the unknown peaks observed in the SIMS results could be interpreted. Moreover, it was found that the dominant impurities having a great influence on the film purity were hydrogen, carbon, nitrogen, and oxygen.     

Laser brazing of a dissimilar joint of austenitic stainless steel and pure copper

In many industries, there are applications that require the joining of stainless steel and copper components; therefore, the welding of dissimilar stainless steel/copper joints is a common process. For this investigation, the optimal brazing conditions and suitable filler metals for laser brazing of stainless steel/copper lap joints were studied. Tensile shear force increases with increases in the laser spot diameter or in the laser irradiation angle, which is associated with increased bonding width; however, as bonding width approaches 2 mm, tensile shear force reaches a saturated value due to fracturing at the HAZ of the Cu base plate. In order to obtain joints with high tensile shear strength, laser brazing was optimized by using Cu–Si-based filler metal under the following conditions: laser power, 4 kW; spot diameter, 3 mm; laser irradiation angle, 80°; irradiation position shift, 0.6 mm; brazing speed, 0.30 m/min; and filler metal feed speed, 0.30 min. Concerning filler metals, it was found that the Ni–Cu type showed relatively large tensile shear force even at high welding speeds in comparison with those of the Cu–Si, Cu, Cu–Ni, Ni–Cu and Ni types, respectively.     

Comparison Study on Additive Manufacturing (AM) and Powder Metallurgy (PM) AlSi10Mg Alloys

The microstructural and mechanical properties of AlSi10Mg alloys fabricated by additive manufacturing (AM) and powder metallurgy (PM) routes were investigated and compared. The microstructures were examined by scanning electron microscopy assisted with electron-dispersive spectroscopy. The crystalline features were studied by x-ray diffraction and electron backscatter diffraction. Room-temperature tensile tests and Vickers hardness measurements were performed to characterize the mechanical properties. It was found that the AM alloy had coarser Al grains but much finer Si precipitates compared with the PM alloy. Consequently, the AM alloy showed more than 100% increment in strength and hardness compared with the PM alloy due to the presence of ultrafine forms of Si, while exhibiting moderate ductility.     

Precipitation Characteristics and Mechanism of Vanadium Carbides in a V-Microalloyed Medium-Carbon Steel

The precipitation characteristics and mechanism of vanadium carbides during isothermal transformation at 650 ℃ in a V-microalloyed medium-carbon steel were investigated through scanning electron microscopy and transmission electron microscopy as well as dilatometry test. Five morphologies of vanadium carbides were found to precipitate at different nucleation sites during the transformation. Two kinds of interphase precipitation form simultaneously in both pro-eutectoid and pearlitic ferrites. The linear arrays of fine interphase precipitates are parallel to the c/a interface, and the fine needles of interphase precipitates are perpendicular to the c/a interface. The vanadium carbides of long or short fibers, coarse particles and fine particles form in both pro-eutectoid and pearlitic ferrites, displaying different precipitation distributions and orientation relationships with ferrite. The precipitation mechanisms of vanadium carbide precipitates with different modes were proposed, and the precipitation sequence of various vanadium carbide precipitates was finally ascertained.     

Molecular dynamics model structures for the molten globule state of {alpha}-lactalbumin: aromatic residue clusters I and II

To model the molten globule structure of -lactalbumin, moleculardynamics (MD) simulations were carried out for the protein inexplicit water at high temperature. In these simulations, long-rangeCoulomb interactions were evaluated explicitly with an originalmethod (particle–particle and particle–cell: PPPC)to avoid artifacts caused by the cut-off. The MD simulationswere started from two initial conditions to verify that similarresults would be obtained. From the last 150 ps trajectoriesof the two MD simulations, two partially unfolded average structureswere obtained. These structures had the following common structuralfeatures which are characteristic of the molten globule state.The radii of gyration for these conformations were 7.4 and 9.6%larger than that of the native state. These values were almostthe same as the experimental value (9.6%) observed recentlyby small-angle X-ray scattering (Kataoka,M., Kuwajima,K., Tokunaga,F.and Goto,Y., 1997, Protein Sci., 6, 422–430). Furthermore,aromatic residues of clusters I and II in these structures werefar apart from each other except for Try103–Trp104. Thisresult is in good agreement with NMR experimental results forthe acid-denatured molten globule state (Alexandrescu et al.,1992, 1993); that is, NOE signals between the aromatic residueswere not observed, except for that of Try103–Trp104 inthe molten globule state. Other structural features of thesemodels for the molten globule state are discussed with referenceto native state structures.     

Determination of residual avoparcin in chicken muscle by HPLC with ultraviolet and amperometric detection

An analytical method was developed for determination of residual avoparcin in chicken muscle by measuring alpha- and beta-avoparcin, major components of the pharmaceutical preparation avoparcin, using HPLC with UV and amperometric detectors. The analytical HPLC was run on a Cosmosil 5C18-AR column (4.6 mm x 25 cm) with a gradient formed from A: 2.5% acetic acid, 0.01 mol/L sodium heptane sulfonic acid-acetonitrile (88.5:11.5) (pH 4.0) and B: 2.5% acetic acid-acetonitrile (10:90), using UV and amperometric detection (AMD) with glassy-carbon electrode (+900 mV). Avoparcin was extracted from chicken muscle by homogenization with methanol-0.2 mol/L sulfuric acid (6:4) followed by centrifugation after pH adjustment to 4 with 1 mol/L sodium hydroxide. The supernatant was evaporated to dryness, and the residue was dissolved in water. The aqueous layer was adjusted to pH 4 by adding 1 mol/L sodium hydroxide. Then it was purified on a Sep-Pak tC18 plus ENV cartridge. The cartridge was washed with water, and retained substances were eluted with 50% methanol. The eluate was evaporated to dryness under reduced pressure. The residue was dissolved in water and determined by HPLC. Recoveries of avoparcin spiked in chicken muscle were 73.1-88.1% at levels of 2-10 micrograms/g. The detection limits were 0.5 microgram/g (UV) and 0.2 microgram/g (AMD).     

Electromagnetic Design Techniques for Liquid Crystal Display Driver ICs

A simple method of verifying electromagnetic interference (EMI) reduction effects for liquid crystal display (LCD) driver integrated circuits (ICs) is proposed. In this paper, we discuss correlations between radiated emissions and high-frequency currents of power system at three different levels: print circuit board (PCB) level, chip level, and functional circuit level. The EMI design points for LCD driver ICs are presented too. Simulated and measured results prove that our EMI design effectively reduces LCD EMI noise.     

Scaling prospect of optically differential reconfigurable gate array VLSIs

Dynamic reconfigurable devices present new computational paradigms because programmable devices’ activity and performance can be improved dramatically by increasing its reconfiguration frequency. Therefore, this paper presents designs of optically differential reconfigurable gate array (ODRGA) VLSIs using 0.18 μm and 0.35 μm CMOS process technologies. Although they are a type of programmable gate array, they can be reconfigured optically in nanoseconds. This paper also discusses future scaling prospects of ODRGA-VLSIs.     

Kinetic and morphological study of a magnesium ethoxide‐based Ziegler–Natta catalyst for propylene polymerization

BACKGROUND: Kinetic and morphological aspects of slurry propylene polymerization using a MgCl₂‐supported Ziegler–Natta catalyst synthesized from a Mg(OEt)₂ precursor are investigated in comparison with a ball‐milled Ziegler–Natta catalyst. RESULTS: The two types of catalyst show completely different polymerization profiles: mild activation and long‐standing activity with good replication of the catalyst particles for the Mg(OEt)₂‐based catalyst, and rapid activation and deactivation with severe fragmentation of the catalyst particles for the ball‐milled catalyst. The observed differences are discussed in relation to spatial distribution of TiCl₄ on the outermost part and inside of the catalyst particles. CONCLUSION: The Mg(OEt)₂‐based Ziegler–Natta catalyst is believed to show highly stable polymerization activity and good replication because of the uniform titanium distribution all over the catalyst particles. Copyright © 2008 Society of Chemical Industry     

High-speed digital-signal transmission experiments by optical wavelength-division multiplexing

The letter reports results obtained with laboratory transmission experiments on high-speed digital signals by optical wavelength-division multiplexing, using a newly developed optical multiplexer and demultiplexer, as well as other high-performance optical devices and fibres.