Effect of Ti Addition and Microstructural Evolution on Toughening and Strengthening Behavior of as Cast or Annealed Nb–Si–Mo Based Hypoeutectic and Hypereutectic Alloys

Room temperature fracture toughness along with compressive deformation behavior at both room and high temperatures (900 °C, 1000 °C and 1100 °C) has been evaluated for ternary or quaternary hypoeutectic (Nb–12Si–5Mo and Nb–12Si–5Mo–20Ti) and hypereutectic (Nb–19Si–5Mo and Nb–19Si–5Mo–20Ti) Nb-silicide based intermetallic alloys to examine the effects of composition, microstructure, and annealing (100 hours at 1500 °C). On Ti-addition and annealing, the fracture toughness has increased by up to ~ 75 and ~ 63 pct, respectively with ~ 14 MPa√m being recorded for the annealed Nb–12Si–5Mo–20Ti alloy. Toughening is ascribed to formation of non-lamellar eutectic with coarse Nb_ss, which contributes to crack path tortuosity by bridging, arrest, branching and deflection of cracks. The room temperature compressive strengths are found as ~ 2200 to 2400 MPa for as-cast alloys, and ~ 1700 to 2000 MPa after annealing with the strength reduction being higher for the hypoeutectic compositions due to larger Nb_ss content. Further, the compressive ductility has varied from 5.7 to 6.5 pct. The fracture surfaces obtained from room temperature compression tests have revealed evidence of brittle failure with cleavage facets and river patterns in Nb_ss along with its decohesion at non-lamellar eutectic. The compressive yield stress decreases with increase in test temperature, with the hypoeutectic alloys exhibiting higher strength retention indicating the predominant role of solid solution strengthening of Nb_ss. The flow curves obtained from high temperature compression tests show initial work hardening, followed by a steady state regime indicating dynamic recovery involving the formation of low angle grain boundaries in the Nb_ss, as confirmed by electron backscattered diffraction of the annealed Nb–12Si–5Mo alloy compression tested at 1100 °C.

     

Synthesis and structural characterization of an alternating double aquo-bridged and single cyano-bridged polymeric barium–iron complex: {[Ba2(phen)4(H2O)6Fe(CN)6]·Cl·2(phen)·3H2O}n

A new alternating double aquo-bridged and single cyano-bridged polymeric complex {[Ba₂(phen)₄(H₂O)₆Fe(CN)₆]·Cl·2(phen)·3H₂O}_n (1) (phen = 1,10-phenanthroline) has been synthesized and structurally characterized. In the crystal structure the two centrosymmetric [Ba₂(phen)₄(H₂O)₆] units are bridged through two trans CN groups of [Fe(CN)₆]³⁻ ion, which results in the formation of a zig-zag polymeric chain. In each [Ba₂(phen)₄(H₂O)₆] unit, the two Ba centers are joined by double aquo bridges. Both the Ba atoms are 9-coordinated with distorted mono-capped square antiprismatic geometry. An elaborate hydrogen bonding system holds the parallel polymeric chains together.     

Microstructure and mechanical properties of mechanically alloyed and spark plasma sintered amorphous–nanocrystalline Al65Cu20Ti15 intermetallic matrix composite reinforced with TiO2 nanoparticles

Multiphase Al₆₅Cu₂₀Ti₁₅ intermetallic alloy matrix composite, dispersed with 10 wt.% of TiO₂ nanoparticles, has been processed by mechanical alloying, followed by spark plasma sintering under pressure in the temperature range of 623–873 K. Differential scanning calorimetry and X-ray diffraction suggest that equilibrium crystalline phases evolve from the amorphous or intermediate crystalline phases. Transmission electron microscopy shows that the composite sintered at 873 K has partially amorphous microstructure, with dispersion of equilibrium, crystalline, intermetallic precipitates of Al₅CuTi₂, Al₃Ti, and Al₂Cu of 25–50 nm size, besides the TiO₂. The composite sintered at 873 K exhibits little porosity, hardness of 5.6 GPa, indentation fracture toughness in the range of 3.1–4.2 MPa√m, and compressive strength of 1.1 GPa. Indentation crack deflection by TiO₂ particle aggregates causes increase in fracture resistance with crack length, and suggests R-curve type behaviour. The study provides guidelines for processing high strength amorphous–nanocrystalline intermetallic composites based on the Al–Cu–Ti ternary system.     

Modeling the oxidative coupling of methane using artificial neural network and optimizing of its operational conditions using genetic algorithm

The effect of some operating conditions such as temperature, gas hourly space velocity (GHSV), CH₄/O₂ ratio and diluents gas (mol% N₂) on ethylene production by oxidative coupling of methane (OCM) in a fixed bed reactor at atmospheric pressure was studied over Mn/Na₂WO₄/SiO₂ catalyst. Based on the properties of neural networks, an artificial neural network was used for model developing from experimental data. To prevent network complexity and effective data input to the network, principal component analysis method was used and the number of output parameters was reduced from 4 to 2. A feed-forward back-propagation network was used for simulating the relations between process operating conditions and those aspects of catalytic performance including conversion of methane, C₂ products selectivity, C2 yielding and C₂H₄/C₂H₆ ratio. Levenberg-Marquardt method is presented to train the network. For the first output, an optimum network with 4-9-1 topology and for the second output, an optimum network with 4-6-1 topology was prepared. After simulating the process as well as using ANNs, the operating conditions were optimized and a genetic algorithm based on maximum yield of C₂ was used. The average error in comparing the experimental and simulated values for methane conversion, C₂ products selectivity, yield of C₂ and C₂H₄/C₂H₆ ratio, was estimated as 2.73%, 10.66%, 5.48% and 10.28%, respectively.     

Contribution of water and cooked rice to an estimation of the dietary intake of inorganic arsenic in a rural village of West Bengal,India

Arsenic contamination of rice plants by arsenic-polluted irrigation groundwater could result in high arsenic concentrations in cooked rice. The main objective of the study was to estimate the total and inorganic arsenic intakes in a rural population of West Bengal, India, through both drinking water and cooked rice. Simulated cooking of rice with different levels of arsenic species in the cooking water was carried out. The presence of arsenic in the cooking water was provided by four arsenic species (arsenite, arsenate, methylarsonate or dimethylarsinate) and at three total arsenic concentrations (50,?250 or 500?µg?l^?1). The results show that the arsenic concentration in cooked rice is always higher than that in raw rice and range from 227 to 1642?µg?kg^?1. The cooking process did not change the arsenic speciation in rice. Cooked rice contributed a mean of 41% to the daily intake of inorganic arsenic. The daily inorganic arsenic intakes for water plus rice were 229, 1024 and 2000?µg?day^?1 for initial arsenic concentrations in the cooking water of 50, 250 and 500?µg?arsenic?l^?1, respectively, compared with the tolerable daily intake which is 150?µg?day^?1.     

Performance and Modeling of the MWIR HgCdTe Electron Avalanche Photodiode

The operation of the mid-wave infrared (MWIR) HgCdTe cylindrical electron injection avalanche photodiode (e-APD) is described. The measured gain and excess noise factor are related to the collection region fill factor. A two-dimensional diffusion model calculates the time-dependent response and steady-state pixel point spread function for cylindrical diodes, and predicts bandwidths near 1 GHz for small geometries. A 2 μm diameter spot scan system was developed for point spread function and crosstalk measurements at 80 K. An electron diffusion length of 13.4 μm was extracted from spot scan data. Bandwidth data are shown that indicate bandwidths in excess of 300 MHz for small unit cells geometries. Dark current data, at high gain levels, indicate an effective gain normalized dark density count as low as 1000 counts/μs/cm² at an APD gain of 444. A junction doping profile was determined from capacitance–voltage data. Spectral response data shows a gain-independent characteristic.     

Improved arsenic doping in metalorganic chemical vapor deposition of HgCdTe andin situ growth of high performance long wavelength infrared photodiodes

Controlled and effective p-type doping is a key ingredient forin situ growth of high performance HgCdTe photodiode detectors. In this paper, we present a detailed study of p-type doping with two arsenic precursors in metalorganic chemical vapor deposition (MOCVD) of HgCdTe. Doping results from a new precursortris-dimethylaminoarsenic (DMAAs), are reported and compared to those obtained from tertiarybutylarsine (TBAs). Excellent doping control has been achieved using both precursors in the concentration range of 3 × 1015-5 × 10¹⁷ cm⁻³ which is sufficient for a wide variety of devices. Arsenic incorporation efficiency for the same growth temperature and partial pressure is found to be higher with DMAAs than with TBAs. For doping levels up to 1 × 10₁₇ cm⁻³, the alloy composition is not significantly affected by DMAAs. However, at higher doping levels, an increase in the x-value is observed, possibly as a result of surface adduct formation of DMAAs dissociative products with dimethylcadmium. The activation of the arsenic as acceptors is found to be in the 152–50% range for films grown with DMAAs following a stoichiometric anneal. However, a site transfer anneal increases the acceptor activation to near 100%. Detailed temperature dependent Hall measurements and modeling calculations show that two shallow acceptor levels are involved with ionization energies of 11.9 and 3.2 meV. Overall, the data indicate that DMAAs results in more classically behaved acceptor doping. This is most likely because DMAAs has a more favorable surface dissociation chemistry than TBAs. Long wavelength infrared photodiode arrays were fabricated on P-on-n heterojunctions, grownin situ with iodine doping from ethyl iodide and arsenic from DMAAs on near lattice matched CdZnTe (100) substrates. At 77K, for photodiodes with 10.1 and 11.1 (im cutoff wavelengths, the average (for 100 elements 60 × 60 μm² in size) zero-bias resistance-area product, R₀A are 434 and 130 ohm-cm², respectively. Quantum efficiencies are ≥50% at 77K. These are the highest R₀A data reported for MOCVDin situ grown photodiodes and are comparable to state-of-the-art LPE grown photodiodes processed and tested under identical conditions.     

Microstructural evolution and hardness of in situ Al-4.5Cu-5TiB2 composite processed by multiple roll passes in mushy state

In situ Al-4.5Cu-5TiB₂ composite has been processed through stir casting method, in which, the TiB₂ particles have been precipitated in situ by mixed salt route involving reactions between K₂TiF₆ and KBF₄.The as-cast specimens containing 20 volume percent liquid content have been subjected to three mushy state roll passes, each leading to 5 percent reduction in thickness. The grain structure has been found to be globular in the mushy state rolled composites. Measurements along the cross-section have shown decrease in average grain size and increase in hardness, as one proceeds along the direction of rolling. On the other hand, grain size and hardness have been found to be more or less similar, when compared for sections perpendicular to the rolling direction.     

Logistics cost analysis of rice straw for biomass power generation in Thailand

The logistics of the fuel supply have a large impact on the economy of a biomass power generation facility, especially for low density biomass fuels like straw. A detailed cost analysis of a typical rice straw logistics process for two baling options in three regions of Thailand shows that the costs for all logistics operations vary from a minimum of 18.75 USD/t for small rectangular bales in the Northern region of Thailand to maximum 19.89 USD/t for large rectangular bales in the North-eastern region. The difference in costs is not very significant due to the higher ownership and operating costs of the equipment for using large rectangular bales; however, the specific fuel consumption cost is substantially lower by around 17.5% and a total transport cost reduction is about 31.5%. Analysis of the logistics economies of scale for projected power plant capacities of 2-35 MW_e showed that each doubling the capacity of the energy facility increases the specific costs of the logistics operations only by around 4% in all regions.